Question about Proxim HOT-STANDBY PROTECTION SWITCH

1 Answer

I have a sony trinitron Model kv27v65 that will not turn on. The standby/timer light blinks four times. It was working fine earlier today and we don't know what caused the problem.

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 6 Answers

Internally the 4 blinks means that the vertical deflection circuitry has Stopped.
This requires repair or replacement depending on your preference.

Sorry for the bad news.

Posted on Dec 27, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I need a password containing 6 to 12 characters and containing a number


1-With the unit on, place a paper clip into the hole on the back of the unit labeled Reset.
2-Hold paper clip down for 10 seconds and release.
3-The unit will reboot on its own. Once the WLAN light stops blinking, the unit is reset.
Resetting the router does not reset the firmware to an earlier version. It will change all settings back to factory defaults

Jul 07, 2013 | Networking Hubs & Switches

1 Answer

Reset linksys SLM224G4S switch


1-With the unit on, place a paper clip into the hole on the back of the unit labeled Reset.
2-Hold paper clip down for 10 seconds and release.
3-The unit will reboot on its own. Once the WLAN light stops blinking, the unit is reset.
Resetting the router does not reset the firmware to an earlier version. It will change all settings back to factory defaults

Jul 04, 2013 | Linksys (SLM224G4S) 24-Port Ethernet...

1 Answer

D-Link DES-1008A Some ports are not connected, how the solution???


D-link 8 ports switch (modle no:DES-1008A,H/W Ver:D1,S/N:Q90K1C6008005) is not working. Pwr led is not blink. how can I trace its? Please.

Jun 16, 2012 | D-Link DES Networking Hubs & Switches

1 Answer

Computer not recognising mp4..


if in Windows, can you go to system restore and choose to restore to an earlier date like yesterday's date. Be sure to copy off any thing saved between then and today.

Jun 15, 2009 | Network Computing Devices (NSH800S/A)...

1 Answer

Sony Trinitron KV-27EXR25


Just this week I had the same problem. If you are hearing a click responding to your pushing on the power button then it is more than likely a short that is preventing the problem. In my case it was a matter of dust.
I fixed the problem by opening up the back of the set and blowing all the dust out. There was a ton of dust accumulated on the circuit boards over the years. Once the dust was cleared I check to make sure the power fuse was not blown and it was fine. I then closed it up and it turned on without a problem.
My Sony is over fifteen years old and it still works like a charm. Its not HDTV, but it works great. When it finally goes; then I will buy a much bigger flat screen HDTV.
Good luck.

Jul 21, 2008 | D-Link DE 805TP (DE-805TP)5x10 Mbps...

5 Answers

D-Link Ethernet Switch Lights Flashing and No Internet


You seem to have a problem with the switch or its power supply. If you have another D-Link device with the same power supply (see the volts and amps on the sticker), we may try switching them.

I one had a problem very similar to yours and changing the power supply solved the problem.

Apr 16, 2008 | D-Link Express EtherNetwork DSS-5+...

3 Answers

Dell Powerconnect 2016 All leds are on, solid no blinking.


Had same problem with my Dell Pwoerconnect 2016, power it on and all LEDs light up but nothing works.
The problem was traced to one or both output capacitors ( 10v 680uf ) on the ( tiny ) power supply.
Capacitor symptoms include bulging or rounded tops instead of flat like new one and the rubber plug in base of capacitor protruding.
Capacitors need to be replaced.
I have successfully replaced with 10v 1000uf and 10v 1200uf, both Rubycon and Sanyo brands.
Power to the switch board is now restored and the switch is able to function just fine.
Give it a go and see if it works for your Powerconnect.
BigAl

Jan 24, 2008 | Dell PowerConnect 2016 (pct2016)...

1 Answer

Network Lockup and all indicator lights ON after popo


If the ports still glow without any device plugged in , there is a hardware problem

Nov 02, 2007 | Linksys EtherFast EF4124 24-Port Ethernet...

1 Answer

Internet down when give gateway


yes, it will work fine. But there is no need to formate. You do one thing try once more. Check modem which is provided by your vender. Switch off & on your modem. Right click on internet explorer -> properties->Delete cookies , delete history-> go to advance -> restore default. Switch off and switch on of your modem. Check four light should be blink. If it is glowing definitely it will work. Good Luck

Sep 06, 2007 | Quintum Tenor DX2060 (501-0122-00)...

Not finding what you are looking for?
Proxim HOT-STANDBY PROTECTION SWITCH Logo

Related Topics:

121 people viewed this question

Ask a Question

Usually answered in minutes!

Top Proxim Networking Hubs & Switches Experts

Mike

Level 3 Expert

4331 Answers

Les Dickinson
Les Dickinson

Level 3 Expert

18298 Answers

Brian Sullivan
Brian Sullivan

Level 3 Expert

27725 Answers

Are you a Proxim Networking Hub and Switch Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...