Question about Frigidaire FTF530E Extra Large 3.1 Cu. Ft. I.E.C. Capacity Washer ENERGY STAR Qualified

1 Answer

Stuck on rinse

Washer runs through first wash cycle then goes to rinse and stalls. I can see water entering chamber but slowly. Makes strange, humming noise at that point too.

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 10 achievements.


    An expert that got 5 achievements.


    An expert whose answer got voted for 500 times.

  • Master
  • 1,294 Answers
Re: stuck on rinse

Check drain hose under the tub by unscrewing clamps to see if there is any blockage in this pipe; also clean out filter in this area. Disconnect from mains before doing so.

Posted on Apr 20, 2007

Add Your Answer

0 characters

Uploading: 0%


Complete. Click "Add" to insert your video. Add


3 Points

Related Questions:

1 Answer

WI815 Intuitive Eco - no cold water

IW Intuitive Eco.
Water valves have a rubber diaphragm that wares out
after some time,
So yes you are right water valves need replacing.

Apr 21, 2014 | Fisher and Paykel Washing Machines

1 Answer

SM 8525492A whirlpool washer rinse cycle no water comes out, just hums

when the washer goes into rinse cycle it only uses cold water so clothes don't rinkle,so most likey you have a problem with your cold water,do this,shut down the water to the washer,remove the water lines from the back of washer and mark them so you know how they came off,stick the hoses into the washer if they reach or a bucket,turn on the cold water to see if water is coming out of hose,if water does come out of hose good then stick the cold water hose back on the washer and run it only on cold,if it doesn't fill then you know you have a problem with the water valve on the washer and it's not the house water valve that's bad,and usually if you have a problem with the washer water valve it will just hum and no water will enter the washer so if you hear a humming sound it will be the water valve.tried looking up the model number you sent but it doesn't come up on the parts lookup

Apr 25, 2013 | Washing Machines

2 Answers

Water for intial fill works fine . when it goes to rinse cycle the water just dribbles in making wash time go on for ever ! whats the solution?

when you start the washer set it just on cold and see if it fills slowly,when the washer goes to rinse it just uses cold water,you could have a problem with the washer or in the house,when you run it on just cold and if it dribbles in,stop it shut down the water going to the washer,remove the cold water hose from the back of the washer,stick it in the sink or inside the washer and turn it on,if it comes out strong then you have a bad water valve on the washer,if it comes out slowly you have a bad water valve in the house and it's not the washer.hope this helps

Sep 12, 2011 | Washing Machines

1 Answer

My whirlpool washer periodically gets stuck on rinse.. the water continues to run but its only about half full so it must be draining. My water bill was over $100 last month, please help.

check the lid switch, if it isn't working right the machine will not enter the spin cycle, also the timer may be going bad, it could stay stuck in between the rinse fill and rinse cycle

Jun 21, 2011 | Whirlpool Washing Machines

1 Answer

My LG front loading washer makes a train noise during the rinse cycle. What could be the cause?

if it is right after the drain cycle; it then goes into a spin. It then starts to fill with water for the rinse while the tub is still turning. The water entering the tub while the tub is spinning, cleans the tub of soap and the water going through the holes in the tub are causing the noise. It is normal if only in the rinse cycle.

Aug 29, 2010 | Frigidaire GLTF1670A Front Load Washer

1 Answer

Water will not stay filled in tub on rinse cycle

It sounds like a siphon issue.
Check that the drain hose does a high loop before it goes into the drain pipe. (ie. drain hose loops above the water level inside the tub). Make sure the drain hose is not pushed too far down into the drain pipe. Also if the drain hose is sealed to the drain pipe this will create an airlock and a siphon will occur, allow air to enter between drain hose and drain pipe connection.
This should help you but if there is still a problem let me know and I'll try to assist you further.
Good luck!

Mar 21, 2009 | Maytag Washing Machines

1 Answer

Kenmore front-load washer stops at rinse cycle

When the washer initially fills for the wash, is it only hot water entering the drum? Try switching the water temperature between hot and cold as it fills. If any of them show little or no water getting through, it sounds too easy but check to make sure water supply taps are on, and that the cold/hot fill hoses aren't reversed. Remove the fill hoses and check any of the screen filters for blockage (in the hoses and in the inlet water valve). When the machine stops and waits to fill but all you hear is a hum, it sounds like there is power going to the valve but water is not able to get through it.
Good luck!

Mar 03, 2009 | Kenmore 43142 Front Load Washer

4 Answers

Water Softner Dispense wont empty - Kenmore Elite Quiet Pak 4 HE3t

I'm sure you heard a small motor running from time to time during a cycle. That moves an "arm" which sends water to the different chambers during a cycle. Fabric softener is dispensed when water goes to that chamber and dilutes the fabric softener. That chamber then empties by a siphoning action.
If you want to narrow down the problem a little to help trouble shoot -- put some wet rags in and run the Rinse and Spin cycle with some fabric softener. If the softener is not dispensed, then you know that the water isn't being sent to that chamber properly.
If you are intrepid enough to take the top off your washer, do that and see if the arm appears to be moving during a normal cycle. Maybe the arm got dislodged or broken during the move.
If water isn't being diverted properly, I think this calls for a real repair person.

Jan 27, 2008 | Kenmore Elite 45986 Front Load Washer

1 Answer

Rinse cycle doesnt work

the humming noise is probably the cold valve operating but no water. check tap not turned off. slowly loosen cold water feed and check if water present

May 02, 2007 | Kenmore 3.2 cu. ft. Plus Top Load Washer

Not finding what you are looking for?
Frigidaire FTF530E Extra Large 3.1 Cu. Ft. I.E.C. Capacity Washer ENERGY STAR Qualified Logo

Related Topics:

122 people viewed this question

Ask a Question

Usually answered in minutes!

Top Frigidaire Washing Machines Experts


Level 3 Expert

4342 Answers

Richard Roth
Richard Roth

Level 3 Expert

9472 Answers

Dan Webster
Dan Webster

Level 3 Expert

8147 Answers

Are you a Frigidaire Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides