Question about Electrolux EWDW6505GS Fully Integrated Dishwasher with 9 Wash Cycles, Nylon Racks, Wave-Touch Contro... 24 in. Built-in Dishwasher

3 Answers

Error code 01 appears

I cannot restart the machine and cancel the error 01 code. There appears to be no leaking from tub. Model # EWDW6505GSO. Thanks!

Posted by on

  • dentureguy Dec 27, 2008

    My electrolux dishwasher Model# EWDW6505GSO has an error 01 code however we cannot find any moisture under the tub. How can the dishwasher be re-set to get rid of the code? The manual does not explain. Thanks!

  • dentureguy Dec 27, 2008

    Thanks guy! You're the man! We followed your steps and used a hair dryer with the breaker shut off and the code disappeared and it works again! The best thing is that tonight we have 20 people over and we did not want to have to do dishes by hand!

×

3 Answers

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Brigadier General:

    An expert that has over 10,000 points.

  • Master
  • 6,966 Answers

Hi and welcome to FixYa,

Initially, the error code "01" indicates a leak or overflow has been detected and flooding is possible. This would refer to the drain area below the tub of the dishwasher. In most occasions, cleaning the filter, strainer, mesh, grid, sump, impeller, pump and hose should address the error code. There are however instances where the error code is persistently displayed even if the aforementioned areas/components have been cleaned and dried. One method of correcting this is to force dry the bottom/under the tub with the use of a can of compressed air, an air compressor, a reversible vacuum cleaner, hair dryer or even a ventilator/electric fan. There have been reports of successful tricks like laying the dishwasher on its side. Thereafter pressing on the STOP, PAUSE or CANCEL for more than 5 seconds should clear the code or unplugging the unit for an extended period of time.

Good luck and Thank you for using FixYa.

Posted on Dec 27, 2008

  • Louie  Role
    Louie Role Dec 28, 2008

    Glad to be of assistance and appreciate the rating too.

  • John Aug 11, 2013

    instead of taking mine appart by pulling it out and flipping it over i just sucked all the water out with a turkey baster, let it stand for an hour then flipped my breaker for 10 mins , and it was good to go.

×

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 15,935 Answers

Leak Detector - When water is detected under the tub.

Posted on Dec 27, 2008

  • blueextc3221
    blueextc3221 Dec 27, 2008
  • blueextc3221
    blueextc3221 Dec 27, 2008


    In certain situations which are critical to the machine

    function and safe operation, the control shall

    shut down and indicate an error code ‘Er’ (See Error

    Codes on page 21). On units without a display, all

    indicator lights will flash.

    If one of these codes are displayed contact the

    Electrolux Customer Care Center at 1-877-435-

    3287
    . They will be able to provide assistance in

    troubleshooting the problem and/or locating an

    authorized service technician, if needed.

×

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Sergeant:

    An expert that has over 500 points.

  • Expert
  • 306 Answers

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Sears Electric Dryer is flashing F01 What is wrong?


The F01 indicates a failed electronic machine control board. This error code can sometimes be caused by a glitch or power surge through the electrical lines. You may be able to clear this code by unplugging the washer for 5 minutes. If the code returns after plugging the washer back in, then the electronic machine control board will need to be replaced.
You can order a new control board from the Sears PartsDirect website.
http://www.searspartsdirect.com/partsdir...
Here's how to do it: http://media.fotki.com/1_p,wkwdftgtbkdgf...


Error code on dryer F01 - Kenmore Elite HE3 Dryer - iFixit

https://www.ifixit.com/.../Error+code+on+dryer+F01 Traduire cette page The F01 indicates a failed electronic machine control board. This error code can ... The Kenmore Elite HE3 is 7.2 cu. ft. capacity electric dryer by Kenmore.

Dryer Sears / Kenmore HE3 - F01 Error Code Main Circuit ...

2q==? 7:35 https://www.youtube.com/watch?v=eWqrn5klxm0 20 avr. 2015 - Ajout? par Jim Dandy Sears Kenmore Dryer Model HE3 - F01 Error Code. Main Circuit Board Repair - Electronic Control Board ...

Error code F1 on Kenmore HE2 electric dryer appeared ...

www.shopyourway.com > ... > Questions Traduire cette page Sears Kenmore HE2 electric dryer; model #11087571601. F1 error message appeared ... Power it back up and see if you still get the F01 error code. If not, then I ...

What does the error code F-01 mean on my Kenmore front ...

www.shopyourway.com > ... > Questions Traduire cette page By unplugging and plugging in the electrical cord, I got the dryer to work again. ... What does the error code F-01 mean on my Kenmore front loaded HE2 dryer? ... My kenmore washing machine 110.46462500 is flashing an error code F.01 ...

Error code on dryer F01 - Kenmore Elite HE3 Dryer - iFixit

https://www.ifixit.com/.../Error+code+on+dryer+F01 Traduire cette page The F01 indicates a failed electronic machine control board. This error code can ... The Kenmore Elite HE3 is 7.2 cu. ft. capacity electric dryer by Kenmore.

Dryer Sears / Kenmore HE3 - F01 Error Code Main Circuit ...

2q==? 7:35 https://www.youtube.com/watch?v=eWqrn5klxm0 20 avr. 2015 - Ajout? par Jim Dandy Sears Kenmore Dryer Model HE3 - F01 Error Code. Main Circuit Board Repair - Electronic Control Board ...

Error code F1 on Kenmore HE2 electric dryer appeared ...

www.shopyourway.com > ... > Questions Traduire cette page Sears Kenmore HE2 electric dryer; model #11087571601. F1 error message appeared ... Power it back up and see if you still get the F01 error code. If not, then I ...

What does the error code F-01 mean on my Kenmore front ...

www.shopyourway.com > ... > Questions Traduire cette page By unplugging and plugging in the electrical cord, I got the dryer to work again. ... What does the error code F-01 mean on my Kenmore front loaded HE2 dryer? ... My kenmore washing machine 110.46462500 is flashing an error code F.01 ...

Feb 04, 2016 | Sears Kenmore Elite Electric Dryer 69278

1 Answer

Error code 01 keeps coming up and will not let dishwasher complete its cycle. My dishwasher no. is ewdw6505gso and it is only 3 years old. I have 2 other appliances that are Electrolux. Please help.


Mine was only a few months old when error 01 arrived - it is a leak. The Electrolux dishwashers have a leak detector at the bottom inside the plastic pan, that when water appears it sets off the code and you cannot restart the dishwasher until you dry the pan out (tip the unit forward and water will come out) but it will keep on doing it unless you repair it - mine was covered under warranty and they replaced a lot of parts at the bottom. Not even a year later it leaked again, but not as bad. I took it apart and removed a fabric pad that sits in the bottom of the pan, it does not go off that much any more since the water evaporates before it does any damage. I think this feature is completely useless - I would rather see a wet spot on the floor than not be able to do dishes... If you got 3 years you are doing well. I will just replace my appliances as they die and never buy Electrolux ever again! PS if a refrigerator is one of your other units, be aware that their main boards can fail and are very expensive to replace. You will know it is blown when your food freezes in the lower compartment and your lights come on instantly instead of glowing up slowly.

Nov 15, 2013 | Electrolux Dishwashers

1 Answer

Electrolux dishwasher DF code after an er 01 code. how to fix at home


Hello Shirley - Typically error code ER01 indicates that a water leak is detected under the tub. Unit will possibly need a hydraulic kit. Try unplugging the unit or flipping the household circuit breaker off. Wait approximately ten minutes and turn the unit back on. Could the error code DF possibly be PF? If so, PF means power failure and you should be able to start a cycle. If the error code continues to display on dishwasher then I suggest contacting a professional to accurately diagnose and repair it.

Sep 30, 2012 | Electrolux EIDW6305GB 24 in. Built-in...

1 Answer

I have a Kenmore Elite He3. It won't complete any wash cycle without stopping and displaying HF. I can restart it but it continues restarts the wash cycle again. Therefore a Heavy Duty wash cycle of...


Hi

Error code FH appears when No water is detected entering machine or Pressure switch trip is not detected. If after 30 seconds the control does not detect water entering machine and then valves will be turned off and the error code will be displayed. Press PAUSE/CANCEL twice to clear the display. If there is no water entering the unit then make sure that the inlet valves are working fine. You may need to check the continuity at the inlet valves. If the valves are fine then check whether inlet water hoses as they might be plugged. Also check for inlet water screen at the valve. However, if the water is entering into the washer then the Drain pump might not be working. Also inspect the Pressure Switch hose whether it is in good condition and properly connected to Tub and Pressure switch. Also check hoses for leak and inspect the flow meter. Hope this helps...

Daniel

Aug 31, 2011 | Kenmore HE2 Plus Front Load Washer

1 Answer

Our Kenmore elite HE3 model 11044921 stops between cycles and flashes an F and then flashes a H continuously. have to cancel and run rinse/drain cycle


Hi


Error code FH appears when No water is detected entering machine or Pressure switch trip is not detected. If after 30 seconds the control does not detect water entering machine and then valves will be turned off and the error code will be displayed.
Press PAUSE/CANCEL twice to clear the display. If there is no water entering the unit then make sure that the inlet valves are working fine. You may need to check the continuity at the inlet valves. If the valves are fine then check whether inlet water hose, it may be plugged. Also check for inlet water screen at the valve. However, if the water is entering into the washer then the Drain pump might not be working. Also inspect the Pressure Switch hose whether it is in good condition and properly connected to Tub and Pressure switch. Also check hoses for leak and inspect the flow meter. Hope this helps...

Daniel

Jan 10, 2011 | Kenmore Washing Machines

2 Answers

The FH error keeps coming up.


Hi


Thanks for using FixYa. Error code F/H means no water was detected entering machine or Pressure switch trip not detected. If after 30 seconds the control does not detect water entering machine and then valves will be turned off and the error code will be displayed. It can also happen if the control has turned the water valves on and after 8 minutes the flow meter has detected 10.5 gallons of water passing through it, but has not detected the pressure switch trip, the valves will be turned off and the error code will flash. You’ll need to Press PAUSE/CANCEL twice to clear the display and then check:

• If there is no water in the unit:
• Make sure that both valves at the water source(s) are turned on all the way.
• Check for plugged or kinked inlet hoses or plugged screens in the inlet valves
• Verify inlet valve operation
• If there is water in the unit:
• Verify Drain pump operation
• Pressure Switch Hose is in good condition and properly connected to Tub and
Pressure switch
• Verify there is not a siphon problem
• Verify wire harness connections to; Inlet Valves, Pressure Switch, Drain Pump,
Flow Meter and Central Control Unit (CCU)
• Check all hoses for possible leaks
• Verify pressure switch operation
• Verify flow meter operation
• Verify CCU operation


Please do rate the solution if the issue is resolved or else revert for further assistance.


Thanks
Rylee

Aug 29, 2010 | Whirlpool Duet GHW9150P Front Load Washer

1 Answer

Ewdw6505gso electrolux. error 1. have turned off


the water will have leaked into the drip pan underneath, which is installed to protect your floors. Unfortunately, only way to get at it is to pull out dishwasher and remove 3 phillips screws that hold it on. In order to repair leaks, Electrolux came out with a "leak kit", which is part number 154769101. Comes with all parts that they had leak issues with

Mar 14, 2010 | Electrolux EWDW6505GS Fully Integrated...

2 Answers

Error code H5-01 sharp MX2300N


pascale_algu

Its a cause by continuous misfeeding. You better find the cause of that problem.

to cancel the code press program key(P), asterisks, clear key, program key . when the stand by for simulation code appears type 14 to cancel the trouble code.

Good Luck

Aug 13, 2009 | Sharp MX-2300N Color Copier

1 Answer

Kenmore Washer 464625 error codes


do they appear right when you start the washer or does it take a few minutes

Jan 11, 2008 | Washing Machines

3 Answers

THE MODEL # IS WFW8300S WHIRLPOOL DUET SPORTS WASHING MACHINE


a power glitch can cause this promblem first push pause cancel twice to clear this error code then try the washer on drain spin and listen for the pump to come on if it does then clear the machine by pause cancle twice then try to start again if code resets then the promblem is most likely the ccu or the board but try clearing the error first if that dont work get back with me and we will run diagnostic mode

Dec 28, 2007 | Whirlpool Duet GHW9150P Front Load Washer

Not finding what you are looking for?
Electrolux EWDW6505GS Fully Integrated Dishwasher with 9 Wash Cycles, Nylon Racks, Wave-Touch Contro... 24 in. Built-in Dishwasher Logo

Related Topics:

946 people viewed this question

Ask a Question

Usually answered in minutes!

Top Electrolux Dishwashers Experts

Mike Cairns
Mike Cairns

Level 3 Expert

3053 Answers

Mike

Level 3 Expert

4334 Answers

kakima

Level 3 Expert

102366 Answers

Are you an Electrolux Dishwasher Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...