Question about HP LaserJet 1320 Printer

1 Answer

How do I "right clk explain. point icon" to open it up?

I have flashing middle icon; but it did print one page after I hit the green button. Other times it was acting like it was pulling a piece of paper out of the tray, but it didn't, the yellow mid ico lite came on again

Posted by on

×

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 14 Answers

Hi  check your pickup roller under the tray. pull out the tray and see just above it if the pickup roller is not broken or warn that can be your problem most likely. the light flashing jams it is like a jam occur because no paper was picked up by the feed assembly of the printer and there is a flagto tell it if a page came through.

Posted on Jan 10, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Why does my printer only print half of a page?


Let's start by trying this:
Unplug the printer power cord from the printer and the wall.
Turn off the PC.
Disconnect the USB cable from both ends.
Plug the printer back in and turn it on.
Now, can you print a self-test page from the printer?
Make sure there is unused, plain white paper loaded in the input tray.
On the product control panel, press and hold the Power button and the Cancel (X) button at the same time.
Release both buttons. The diagnostic page prints.
If that does not work, are there any blinking lights on the printer? This document might explain them: Blinking lights.
If the self-test page does print normally, reconnect the USB cable, turn the PC back on and try to print a Windows test page:
Click the Windows icon and then click Control Panel . The Control Panel opens in a new window.
Click Hardware and Sounds .
Click Printers . The Printers folder opens.
Right-click the printer icon in the Printers folder.
Click Properties . The printer Properties window opens.
In the General tab, click Print Test Page . The Windows Printer Test Page prints.
If you have problems printing from Windows, you can try some of the troubleshooting steps in this document:
Printer Prints Blank Paper.
Finally, you may have to uninstall and reinstall the print driver.

Jun 03, 2015 | Office Equipment & Supplies

1 Answer

My printer is not working... on screen it displays error 5200? the orange light flashes eight times. what will i do?


Before doing Resett ,Printer must be Ready (Service mode) , How to service mode;

  • Turn off Printer ( POWER + USB cable attached).
  • Press and hold RESUME button? .
  • Press and hold POWER button then free RESUME button But hold POWER button .
  • Press RESUME button five times (5x). not 4xprinter will turn off, but temporary.
  • Free both of button , the lamp indicator will ready in green /ready (printer will Found new hardware = canon device) Annoy it
  • Service tool v_1074.exe
  • Pairs of paper in the printer.
  • Find CLEAR INK COUNTER colom then click MAIN .
  • Printer will print
  • Turn off printer.
  • Turn on printer .
  • Printer is ready for use.

Reset Canon iP2770 error 5200

1. Turn the printer, and printer will look normal.
2. Run the printer for printing documents or print test, then the 5200 error will appear.
3. Jump unplug the power cord without pressing the on-off
4. Open it and slide it into the middle catridgenya manually (press the white penguncinya hook behind the head, for cartridge can be pulled into the middle)
5. Unplug all cartridges and leave the lid remains open
6. Turn the printer, hit the head will move left and right because the lid was still open and will stop in the middle.
7. Replace the cartridge, and close the correct
8. Your printer will return to normal

download: http://www.ziddu.com/download/14828683/ServiceTool_V1074.rar

Aug 29, 2011 | Canon Pixma iP2700 InkJet Photo Printer

2 Answers

TLP 2844-Z is faded on the right half when it prints


It probably needs a print head adjustment or calibration.
Here is a link for the user guide,(it takes a minute to load and display) you will find cleaning and diagnosing tips :
http://www.systemsprintmedia.co.uk/downloads/ZEBRA%20TLP%202844Z%20MANUAL.pdf

If your zebra label printer is not feeding to the next label correctly it may need to be calibrated. Follow these steps to calibrate the printer:
  1. Turn off printer and have media loaded (on older Transports, with no ON/OFF switch, remove battery).
  2. Hold feed button down, and turn printer back on (on older Transports, re-insert battery) while holding down the feed button.
  3. When the light starts flashing, release the feed button.
  4. Printer light will turn green and advance a few blanks.
  5. After printer stops advancing and prints the internal information, press the feed button one time.
  6. You will get another label with the “Out of Dump” message on it.
  7. Printer is now ready for use.
Click on this link or copy and paste the complete link into your browser.
If I could be of further assistance, let me know. If this helps or solves the issue, please rate it.
Thanks, Joe

-->

Apr 21, 2009 | Zebra TLP 2844-Z Thermal Label Printer

1 Answer

I have a HP LaserJet 1320n printer and it will not print. An orange light keeps flashing by the triangle with an exclamation point in it. I printed a test page and it was okay. It will not print...


Possible Solution to your issue!

Blinking Attention Light HP LaserJet 1320 Series Printer - The printer displays an orange blinking attention light which will not clear. This usually indicates one of the following issues have occurred. Perform the following in the order provided to troubleshoot and resolve the issue.
1. Insufficient power. Disconnect the power cord from any surge protectors or power strips and plug the unit directly into an electrical wall outlet.
2. There is a paper jam in the printer.
3. The top cover is open. Open the top cover, reseat the print cartridge, and close the top cover, making certain it is shut properly.
4. No paper was loaded in tray 2 or the tray was not loaded properly causing a mispick. Perform the following steps to load tray 2.
A. Pull the tray out of the printer and remove any paper.
B. Move the blue side width guide outward to match the paper size that is being loaded. Locate the blue guide pointer on the left side of the tray. If using a letter-size (8.5 by 11 inch) paper, match the guide point with the LTR/LGL engraving located on the bottom, left-side of the lift plate.
C. Locate the blue tab on the rear paper-length guide. Locate the triangle-shaped pointer in the middle-right on the bottom of the tray. Press on the blue tab and adjust it so that the triangle-shaped pointer matches the paper size that is being loaded. If using letter-size (8.5 by 11 inch) paper, match the triangle-shaped pointer with the LTR engraving on the bottom of the tray.
D. Place the paper in the tray and make sure that it is flat at all four corners. Keep the paper below the height down arrows on the paper-length guide in the rear of the tray.
E. Slide the tray back in the printer.
5. The tray 2 paper level indicator is stuck.
6. If the printer comes back to a Ready state, print a Self-Test/Configuration page. If the printer is not in a Ready state, proceed to step 7.
A. Verify the printer is in a Ready state. (The green LED next to the U-shaped icon is on steady and no other lights are on.)
B. Press down on the green GO button until the orange Attention light comes on (approximately 5 seconds), and then immediately release the GO button. The green GO button will begin to blink and a Self-Test/Configuration page will print.
7. If the attention light is still on, perform a cold reset. A cold reset, sets most, but not all, default variables stored in NVRAM back to the factory default values. It typically does not reset the page count, paper tray sizes, localization language, or formatter number. Complete the following to perform a cold reset.
A. Turn the printer off.
B. Press and hold down the green GO button.
C. Turn the printer on and continue to hold the green GO button for at least 5 seconds, but not longer than 15 seconds. During the process, the Attention LED will turn on.
D. Release the GO button.
NOTE: If both the Attention light and the Ready LEDs turn on before the GO button is released, the cold reset procedure must be started over at step 1.
E. The printer LEDs begin cycling. The cold reset process runs until completion and the printer returns to the Ready state

Feb 23, 2009 | HP LaserJet 1320n Printer

2 Answers

The icon with the exclamation in the middle is flashing, and


Put your mouse pointer on the Icon, the with your middle finger only, press down on the right side of the mouse. This will bring up a menu on the Icon.

Dec 27, 2008 | HP LaserJet 1320 Printer

1 Answer

Print Problem Go Light Flashing wont print till pushed


Sounds like its waiting for a manual feed. Check the paper you have in the tray and that the selectors on the tray are properly positioned. Once that os done, on the computer side hit the start ICON on your desktop, then control panel, then printers and faxes. Double click on your 2100 print driver to open it. Go into properties and make sure it says "automatic" for tray select. Hit the advanced key and check that it says letter or whatever paper size you have in the tray.

Verify the other settings and then save it.

That should solve your issue.

Aug 07, 2008 | HP LaserJet 2100 Printer

1 Answer

HP 3030 printer


Nobody likes giving bad news, but removing power from the printer while in operation has a very good chance of damaging the cirucitry of the printer.

Next time, simply open the paper tray, which will cause an error light to come on and the print job will stop. Or hit the cancel button on top of the printer. Either way, after that you can turn the power switch off, unplug the power, and then cancel the print job from your computer if the print icon is still present on the bottom right corner of your screen.

You may be able to bring the printer to a service technician to repair the problem, but it might not be fixable at this point.

Jul 11, 2008 | HP LaserJet 3030 All-In-One Printer

2 Answers

Incorrect Paper Size Canon super G3 fax


Sometimes turning it off and on again fixes it. However, we started having a problem where it would print out one page after you powered it back on again and then give the "incorrect paper size" message. I've found that by either holding down the green button or repeatedly pressing it while it powers back on (and held until the first page prints) fixes the problem.

Jun 02, 2008 | Canon - SUPER G3 FAX BOARD-T1 (0450B002AA)

1 Answer

Prints Faint green horizontal lines


Go to control panel and printers and faxes and right click on printer icon then hit printing preferences, go to maintenance and do head cleaning cyles and print nozzle check. if it comes out fine trash and reinstall driver
download driver from support.epson.com site after selecting the printer mdel on the lists

Apr 12, 2008 | Office Equipment & Supplies

1 Answer

Green print


Try cleaning your ink nozzles or ink jets. It sounds like you have a plugged nozzle or two. Your printer program should have maintenance options that allow you to test for plugged nozzles and clean them.

In control panel, open the printing/fax icon, right click on your printers icon, left click properties, then on the bottom of the page the panel that opens you will see a button that says printing preferences, and that should open your print program.

This will work for all printers, not just hp.

Nov 26, 2007 | HP DeskJet F380 All-In-One Printer

Not finding what you are looking for?
HP LaserJet 1320 Printer Logo

55 people viewed this question

Ask a Question

Usually answered in minutes!

Top HP Office Equipment & Supplies Experts

Seeker5211
Seeker5211

Level 3 Expert

1089 Answers

kakima

Level 3 Expert

102366 Answers

mukhtar21 shaikh
mukhtar21 shaikh

Level 3 Expert

2017 Answers

Are you a HP Office Equipment and Supply Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...