Question about RCA Universal Remote 3 Device Remote Control

1 Answer

RCR3273 can't switch input/tv botton on remote to watch dvd

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Contributor
  • 22 Answers

It may be you have the wrong code assuming everything else works fine.

Go to:

http://66.77.167.109/rcaaccessories/RcaaccessoriesController.do?ACTION_TYPE_ID=ACTION_TYPE_CATEGORY&ACTION_CATEGORY_ID=STR_CATEGORY_UNIVERSAL_REMOTES

and on the left of the nav towards the bottom you'll see the remote code finder.

Click the link and select your model number from the dropdown, in this case, RCR3273 and then select your device from the dropdown. The codes are listed by manufacturer alphabetically. Find the codes for your brand of TV and try all of them.

Good luck.

Posted on Feb 04, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

The input control button not working


Usually there is a input button on the TV itself.

Oct 16, 2012 | Toshiba Ct-90302 Remote Control

1 Answer

Not connecting proper audio input


Try:

Learning the input commands for the audio device.

Increasing the inter-device delay and power-on delay for the audio device.

Mar 02, 2010 | Logitech Harmony 550 LCD Remote Control

1 Answer

My remote control is broken. How do I watch DVD's


Hello Boye4522,

If you connect your Dvd player up via a scart lead directly to the back of your Tv when you turn on the DVD player this will send a voltage to the tv telling it to change to the input that your Dvd player is on.

Job done.

Cheers Little Dish Fitter.

Nov 15, 2009 | RCA RCU300WBL Remote Control

1 Answer

I cant find the paper to program my remote to my tv i need the istructions and the code my tv is a panosonic


I cant find the paper to program my remotecontrol the tv.vcr.dvd and is ha rca rcr3273

Oct 29, 2009 | RCA Universal Remote Control

1 Answer

Auxillary channel for dvd


You need to determine what output options your DVD player has. Take a look at the rear of the player. It will certainly have RCA jacks for video and audio outputs (yellow for video, red and white for right and left channel audio). It may also have RCA jacks for component video (marked Y, Pb and Pr). Finally, it may have a threaded connector marked "out to TV" or "antenna out" or something similar. This is called RF output.

Most players today don't offer RF output because nearly every TV has direct AV inputs available. If your DVD player has RF output, connect the output connector to the TVs antenna input. You need a coaxial cable with F-connectors on the ends. One may have been supplied with the player. RF output is on channel 3 or 4, set by a switch on the back of the player or by its on-screen setup. Just set the TV to that channel to watch a DVD.

If your player doesn't have RF output, you connect it to the TV using the AV jacks. You need cables with RCA plugs to to connect the video and audio from the player to the TV. Then you switch the TV to its video input to watch the DVD.

This is where you might run into problems. Many TVs need the original remote control to switch inputs. (Some older RCA sets used channels 90, 91 and 92 to switch to their video inputs so any remote would work, but these sets were made before 125-channel tuning became standard. If your set is one of those models, those are the auxiliary channels you heard about.) If you can't switch the set to video input with front panel buttons and you don't have the right remote, you're not completely out of luck.

If you can't use your set's AV inputs or it just doesn't have any, you need an RF converter. These cost around $15. They take the audio and video from the DVD player and convert it to channel 3 or 4. Then you hook that output to your TV as described above.

May 17, 2009 | RCA Universal Remote Control

2 Answers

Rca universal remote rcr3273


I have the Durabrand TV and I need the directions on how to set up the DVD?

Jul 22, 2008 | RCA Universal Remote 3 Device Remote...

1 Answer

My new universal remote


Jo have you plugged in the Audio and Video cable in correctly. You need to check that the Video cable is in the corresponding input on the TV

Jun 08, 2008 | RCA Universal Remote Control

Not finding what you are looking for?
Remote Controls Logo

Related Topics:

89 people viewed this question

Ask a Question

Usually answered in minutes!

Top RCA Remote Controls Experts

The Knight
The Knight

Level 3 Expert

68368 Answers

andy williard
andy williard

Level 2 Expert

226 Answers

Cindy Wells

Level 3 Expert

4761 Answers

Are you a RCA Remote Control Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...