Question about Reddy Heater RH125T Kerosene Forced Air Heater - 125,000BTU

Open Question

I need a wiring diagram for a Reddy Kerosene Heater Series 125T

All the wires from the wiring diagram were pulled off and we need a diagram to connect them back.

Thank you,
Jill Cargill

Posted by on

  • jmbiringer Dec 27, 2008

    I still need the wiring diagram for the Reddy Heater. I am not interested in the Premium Assistance plan but would appreciate the info.



    Thanks, Jill

×

1 Suggested Answer

  • 188 Answers

SOURCE: I need a wiring diagram

Here is a link to a owner's manual for a RL125T ... http://12.153.20.74/manuals/110429-01C.pdf. You can find a wiring diagram on page 19. I hope this helps you.

Posted on Apr 13, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Need to find pump pressure & nozzle part # for reddy heater 125T


Hi,
Here are a couple of tips that I wrote that tell you how to troubleshoot aTorpedo or Reddy heater...

Reddy Heater - Troubleshooting Torpedo Heaters Torpedo Heater Pump Pressure Adjustment
heatman101

/././

Feb 05, 2011 | Reddy Heater-170,000 BTU Kerosene Deluxe

1 Answer

I have a Reddy heater 125T and the transistor for the ignition is burned into, i was wondering if it is possible to solder a new transistor to the board, and if so what would be the part number for the...


Yes, I have done it and got transistor from a electroic story. took old one to them and they match it. When soldering it on use very little heat not meld the other solder tracks. Ken'Repair

Jan 22, 2011 | Reddy HEATER RH125T 125,000-BTU...

1 Answer

Where can I find a manual for a Reddy Heater 125T?


Pretty sure this is the manual as i think DESA make them.

http://www.fncuthbert.com/pdfs/masman1.pdf

Just cut and paste this link

Aug 29, 2010 | Reddy Heater RH125T Kerosene Forced Air...

1 Answer

170T will not kick on when I plug it in and turn the switch on. I have power the the switch and the thermostat but no power past the board.


I have a 125t that would do a similar thing, found out that on the board a micro resistor or diode whatever would short and fry the board. Check your board carefully following the lead from the igniter wires. Hopefully that is not the problem because then its a new $$$$$ board!

Jan 07, 2010 | Reddy Heater-170,000 BTU Kerosene Deluxe

1 Answer

IGNITER SWITCH


If you have one of these 125T Models- RH125AT, RHD125AT, RL125AT, RM125AT, RE125AT, M125AT, PKHD125T, TKU125T, UKU125T, RD125T
The web address is:
http://www.reddyparts.com/
There are 3 ways to order your part.

Dec 21, 2009 | Reddy Heater-170,000 BTU Kerosene Deluxe

1 Answer

Fuel filter


take the side cover of and you will see where the fuel line goes into the tank. typicall the cap turns clockwise to remove and the filter is hooked right to the cap.

Jan 26, 2009 | Reddy Heater-170,000 BTU Kerosene Deluxe

1 Answer

RH125T won't fire


Not much to check. The element comes out and makes a square loop back to the ceramic portion. This element is extremely brittle and will break if touched or wiped off.

You can check the 2 wires with a voltage tester set on continuity. The needle should swap sides if the ignitor is intact. I don't ever remember an ignitor failing, except for breakage.

View this page. Be sure you get the correct ignitor. 2 different ones have been used on the RH125T.
http://www.reddyparts.com/125T%20ignitors.htm

Dec 28, 2008 | Reddy HEATER RH125T 125,000-BTU...

1 Answer

I need a wiring diagram for a Reddy Kerosene Heater Series 125T


Here is a link to a owner's manual for a RL125T ... http://12.153.20.74/manuals/110429-01C.pdf. You can find a wiring diagram on page 19. I hope this helps you.

Dec 26, 2008 | Reddy Heater RH125T Kerosene Forced Air...

2 Answers

Won't light


Are the ignitors intact? In other words, does the element make a loop back to the ceramic portion. The purpose of the LED is to notify the user of a defective ignitor. The other possibility is a bad control board.

If the ignitor is intact, but no power coming from the board (ignitor only glows for 5 seconds), then the board is bad or the fuse is blown. You might want to test the photocell while you are at it.

You will need to locate the correct model numbers to order the correct parts. "170T" & "125T" are only part of the correct model designation.

Post back if you have further questions.

Oct 23, 2008 | Reddy Heater-170,000 BTU Kerosene Deluxe

Not finding what you are looking for?
Heaters Logo

Related Topics:

351 people viewed this question

Ask a Question

Usually answered in minutes!

Top Reddy Heaters Experts

Mack Baxter

Level 3 Expert

377 Answers

paulcarew

Level 3 Expert

1862 Answers

Superior Maintenance

Level 2 Expert

63 Answers

Are you a Reddy Heater Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...