Question about HP LaserJet 1020 Printer

2 Answers

How to refill toner cartridges HP Q6000 black? (printer HP 2600n)

Can anyone help me to teach where to pierce a hole(s) to remove residual toner powder, where to put fresh toner powder, how much quantity to inject inside the cartridge and how to reset the toner cartridge after refilling?

Posted by on

  • 240cpa May 11, 2010

    I usually take mine to a local store and have them refilled, but I do know that I've never heard of anyone pulling toner out, only putting toner in the cartridge.

×

2 Answers

  • Level 1:

    An expert who has achieved level 1.

    MVP:

    An expert that got 5 achievements.

    Governor:

    An expert whose answer got voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Contributor
  • 27 Answers

No holes are need it
check this video it is very easy with no special equipment
http://www.youtube.com/watch?v=iMiTopIVMxM

Posted on Sep 30, 2010

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Novelist:

    An expert who has written 50 answers of more than 400 characters.

    Governor:

    An expert whose answer got voted for 20 times.

  • Expert
  • 91 Answers

How to refill toner cartridges HP Q6000 black? (pr - 7c02b24.jpg HERE ON THE RED POINT you must to open a hole of 5mm, and with and vaccum, aspire all the residual toner.
HERE THE INSTRUCTIONS FOR OPEN THE CARTRIDGE http://www.uninetimaging.com/newsletter/HP_2600_Reman_Eng.pdf
WHEN you separate the cartridge in two parts, PAGE 10, fig 9 lOOK the right part, in there, you must open a hole for put fresh toner, the hole must be around 2 cm, and the quiantity is 80GR of toner.
Unlock after recharged cartridges for the printer to stop printing without changing the chip

For that we must go to the printer control panel

1 Main Page (Press the green button)
2 × SET SYSTEM (Das to the arrows until you see and then press the green button)
3 • Print quality (Das to the arrows until you see and then press the green button)
4 · replace consumables (Das to the arrows until you see and then press the green button)
5 · IGNORE SOLD, confirmed and ready, with the green button

Now the printer will begin to recognize your chips calibrated and spent.

Posted on Apr 07, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How kyocera works


developer and toner are two drifernt things you have to check to see if the developing unit is installed correctly

Jul 27, 2014 | Kyocera Km-3060 Mfp Copier Copy Machine...

Tip

Why i get black streaks on paper in laser printer prints?


there are some possibilities for this problem. i will explain it. 1) First of all check out if the toner is full ,half or near to empty. There is no exact procedure to check the powder left in the toner without opening the toner.but in one toner there comes about near to 1500 copies.if you have got about 1200 to 1300 copies.then its quite possible that the power left is near to empty so the streaks comes on the paper due to less powder left.many times in this case removing and shaking the toner then reinserting the toner again and checking the printout helps. 2) But if you are sure that toner is not empty then other possibility is.in the toner cartridge there is a aluminium drum.its easily seen in the cartridge.once you remove the cartridge. if that drum is got very much used then due to that drum the streaks appear.fox example.if the drum is new the print is very dark.if the drum gets old the print gets very light or with streaks or faded print. 3) Now if drum and toner powder both are proper and still the problem then its the fault in the printer.in your printer there is some toner powder got spilled out on the inner parts from where the printing paper passes.so when the paper passes from the part where the powder is fallen or got collected then the streaks comes.in this case the printer needs internal cleaning and servicing. 4) but in some cases it has been noticed that internal powder of the toner becomes moist and very hard to come out from the toner for printing.in this case either toner needs to be refilled or toner needs to be replaced.you can get the toner refilled from local cartridge refilling store or local stationery shops dealing in cartridge refillings.The cartridge refilling shops also have the same printer for checking the cartridge.so at the refilling shop it will be confirmed whether the fault is in cartridge or printer.
This will help. Thanks .

on Mar 18, 2010 | Office Equipment & Supplies

3 Answers

My problem is that after refilling the tonner it is giving me low quality of xerox and putting contrast at high initially it was working very nicely please give me right suggession


Please use good quality toner and then try it, it will best to use genuine cartridges, rather than refiiled ones, because that will save your money for a long run.

Aug 28, 2012 | Brother DCP-7030 Digital All-in-One Laser...

1 Answer

How to refill ink in it


The printer doesn't use ink, it uses toner, a black powder. The toner is then pushed onto the page using magnetic force and fused to the paper using a laser. Which replaces the traditional "ink injection" method.

The toner cartridge is a black unit that pulls out located behind the top access panel in the front. This unit contains a glass drum and behind it a well of toner powder. Usually you have to replace the entire unit.

There are toner cartridges with plastic caps which can be removed and then refilled with the powder. However, this powder is messy, difficult to manage, and eventually the drum will become scratched and worn since it is not really designed for prolonged use. So I recommend just replacing it.

While the toner cartridge will run more than ink. The frequency with which you have to replace it is significantly less. So while ink can run you as much as $0.25 a page when you factor in the wear and tear on the printer. Laser printers are more along the lines of $0.04 a page.

If you replace the toner, read the directions carefully and be sure to remove the plastic shipping strip from the side of the cartridge. This strip is used to hold the toner in the cartridge while it ships and will keep it from working properly.

May 12, 2010 | Canon LASER SHOT LBP-2900 Printer

1 Answer

The pages come out with a grey tint. Can I clean


Remove the toner - using a can of air blow the printer out. I would really suggest after that trying a fresh toner.

Jun 18, 2009 | Lexmark C530dn Laser Printer

1 Answer

We need local repair person


I don't understand your website. I was charged 14.99 or so yesterday on my visa, but after your company accepted my payment, I learnedno one was available to help me. So I waited and this morning I have an email that is asking me to pay again or tell me how I fixed the problem.

It really is a simple problem that should be handled by you with a phone call rather than a lengthy internet procedure. I pulled out the toner tray and the bottom tray remained while the top came off and the powder spilled everywhere. I don't want to use a household vacuum on it. It is a mess. I need an approach to unhook the stuck bottom toner tray of the Mita DC 1455 (an old but serviceable copier) and replace the spilled toner with a new module. And how do I clean up spilled fine toner powder which is everywhere?

Jul 24, 2008 | Kyocera Mita FS 3800 Laser Printer

3 Answers

LEXMARK C500


If you open your printer front and pull out all the toner cartridges, on the left, you will see 4 LED lights vertically in a column that match up with 4 matching red light receptor sensors on the right side. Each toner cartridge has a tiny window on each side. When the toner powder level drops below the window level, a light passes all the way through the cartridge from the LED light to the light receptor and trips the printer to display the low toner warning.

The goal is to BLOCK THE LIGHT. The easiest way is to put electrical tape over the window on the right side of each cartridge window. To ensure you have the proper hole, just shine a flashlight in the hole and you will see the reflection from the tiny plastic window.

Jun 14, 2008 | Lexmark C500n Laser Printer

3 Answers

What is waste toner.


We've printed for years using gallon jugs of waste toner nabbed from Quick Print Shop* dumpsters. We just pop the white plug on our cartriges, fold a paper plate into 4ths, snip the tip to make a funnel, and dump it in a half cup at a time!

*Names changed, LOL

May 14, 2008 | Office Equipment & Supplies

Not finding what you are looking for?
HP LaserJet 1020 Printer Logo

2,026 people viewed this question

Ask a Question

Usually answered in minutes!

Top HP Office Equipment & Supplies Experts

Vinaya Kumar...
Vinaya Kumar...

Level 3 Expert

1121 Answers

Seeker5211
Seeker5211

Level 3 Expert

1088 Answers

kakima

Level 3 Expert

98816 Answers

Are you a HP Office Equipment and Supply Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...