Question about Sony KP-46WT510 46" Rear Projection HDTV

5 Answers

Standby Light Flashing

It flashes 9 times...then pauses...9 times...then pauses...

Posted by on

  • jkrnlr Dec 26, 2008

    The problem is not intermittent.

×

5 Answers

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that has over 10 points.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Expert
  • 100 Answers

Its confirm problem of the switching regulator.replace the regulator to solve this problem 100%.

Posted on Dec 26, 2008

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 15,935 Answers

I replaced the 6301 diode and put the G board back in and now the TV isn't giving me the 9 blink error code anymore and I think it starts up just fine.

Posted on Dec 26, 2008

  • blueextc3221
    blueextc3221 Dec 26, 2008

    replacing the G-board or the D6116 & D6301 diodes will fix the issue

×

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 10,594 Answers

If it is Sony KP-46WT510 model then 9 times blink shows error is sound section.

Possible causes are as follows...

+19 and -19 volts missing on A & B boards.
IC708 is defective on A board.
PS701 & PS702 (pico fuses) are open in A board.

Let me know if problem doesn't solve.

Posted on Dec 26, 2008

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 2,110 Answers

It has to be power supply most likely stand by supply. I would check the regulator transistors first along with the horizontal out put transistor. Your set isnt going into protective shutdown so it has to be something in stand by or the start up circuits.

Posted on Dec 26, 2008

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Sony Master
  • 13,433 Answers

The diagnosis of Nine blinks - Replace D 6116 and D 6301 on the "G" board, do not resolder as this will fix the problem temporary. Or Panel Module Error or Thermal Error. If it is intermittent 9 blinks, meaning sometimes the TV comes on and other times you get flashing, then change the switching regulator on the "G" board or check connections. Make sure the regulator is -12 or -13 (negitive).

If this is hebrew for you, I suggest you take the television to a repair professional, if you are going to repair this yourself do at your own risk I suggest you get your hands on a service manual for help in the repair process.

Posted on Dec 26, 2008

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Lg60pn6500 sound comes on no picture after three seconds totally shuts off the Light blinks 3 times and clicks when I turn it on


Those blinks [flashes] are fault indication (Error Codes). From the number of blinks occur at one time switch ON, you can get an idea about the faulty circuit section inside it. This will make repair easy. These are called blinking codes. Make sure about the exact number of blinking of the standby/power LED, by switching On & OFF the set, for at least two times. Count it carefully. If you wish to get some details, check the site linked here. It has details about blinking codes, and fault locating procedure, to many popular brand TVs and other devices.
http://homenol.blogspot.com/
http://electronicshelponline.blogspot.com/
If blinks continue without any pause, the main board is faulty.
Search the site by type in the "brand name" to your device, in the "Search box at the top right of the display window of the Homepage" to get gathered related posts.

Jan 14, 2017 | Televison & Video

2 Answers

Blinking green power light on WD65737 for a minute or so then shut down, Will also go to welcome screen and then shut down


Those blinks [flashes] are fault indication (Error Codes). From the number of blinks occur at one time switch ON, you can get an idea about the faulty circuit section inside it. This will make repair easy. These are called blinking codes. Make sure about the exact number of blinking of the standby/power LED, by switching On & OFF the set, for at least two times. Count it carefully. If you wish to get some details, check the site linked here. It has details about blinking codes, and fault locating procedure, to many popular brand TVs and other devices.
http://homenol.blogspot.com/
http://electronicshelponline.blogspot.com/
If blinks continue without any pause, the main board is faulty.

Jan 13, 2017 | Mitsubishi WD65737 65 inch DLP 1080p HDTV

2 Answers

Bush tv flashes between standby and on red light then blue but will not turn on


Those blinks [flashes] are fault indication (Error Codes). From the number of blinks occur at one time switch ON, you can get an idea about the faulty circuit section inside it. This will make repair easy. These are called blinking codes. Make sure about the exact number of blinking of the standby/power LED, by switching On & OFF the set, for at least two times. Count it carefully. If you wish to get some details, check the site linked here. It has details about blinking codes, and fault locating procedure, to many popular brand TVs and other devices.
http://electronicshelponline.blogspot.com/
If blinks continue without any pause, the main board is faulty.
Search the site by type in the "brand name" to your device, in the "Search box at the top right of the display window of the Homepage" to get gathered related posts.

Jan 13, 2017 | Bush Televison & Video

2 Answers

Panasonic TC-P46C2 Plasma TV. When you turn it on makes a clicking noise then red light stays blinking all the time. What part is likely to be defective?


Those blinks [flashes] are fault indication (Error Codes). From the number of blinks occur at one time switch ON, you can get an idea about the faulty circuit section inside it. This will make repair easy. These are called blinking codes. Make sure about the exact number of blinking of the standby/power LED, by switching On & OFF the set, for at least two times. Count it carefully. If you wish to get some details, check the site linked here. It has details about blinking codes, and fault locating procedure, to many popular brand TVs and other devices.
http://homenol.blogspot.com/
http://electro-medical.blogspot.com/
http://electronicshelponline.blogspot.com/
If blinks continue without any pause, the main board is faulty.
Search the site by type in the "brand name" to your device, in the "Search box at the top right of the display window of the Homepage" to get gathered related posts..

Jan 13, 2017 | Panasonic Televison & Video

1 Answer

The light on my TV is blinking in a 1-2-2-2-1 pattern but nothing happens when I try to turn it on


Those blinks [flashes] are fault indication (Error Codes). From the number of blinks occur at one time switch ON, you can get an idea about the faulty circuit section inside it. This will make repair easy. These are called blinking codes. Make sure about the exact number of blinking of the standby/power LED, by switching On & OFF the set, for at least two times. Count it carefully. If you wish to get some details, check the site linked here. It has details about blinking codes, and fault locating procedure, to many popular brand TVs and other devices.
http://electronicshelponline.blogspot.com/
If blinks continue without any pause, the main board is faulty.
Search the site by type in the "brand name" to your device, in the "Search box at the top right of the display window of the Homepage" to get gathered related posts.

Jan 12, 2017 | Televison & Video

1 Answer

MY dstv DSDD 1132 decoder is flashing red and green lights but yellow light is steady. tv is black and remote not responding


Those blinks [flashes] are fault indication (Error Codes). From the number of blinks occur at one time switch ON, you can get an idea about the faulty circuit section inside it. This will make repair easy. These are called blinking codes. Make sure about the exact number of blinking of the standby/power LED, by switching On & OFF the set, for at least two times. Count it carefully. If you wish to get some details, check the site linked here. It has details about blinking codes, and fault locating procedure, to many popular brand TVs and other devices.
http://electronicshelponline.blogspot.com/
If blinks continue without any pause, the main board is faulty.
Search the site by type in the "brand name" to your device, in the "Search box at the top right of the display window of the Homepage" to get gathered related posts.

Jan 12, 2017 | Televison & Video

2 Answers

I have a sharp aquos tv model lc-32m400x. When i turn the power on via button at the back the green light comes on for about 10secs then turns to red and flashes about every 11/2 - 2secs. Any ideas.


Those blinks [flashes] are fault indication (Error Codes). From the number of blinks occur at one time switch ON, you can get an idea about the faulty circuit section inside it. This will make repair easy. These are called blinking codes. Make sure about the exact number of blinking of the standby/power LED, by switching On & OFF the set, for at least two times. Count it carefully. If you wish to get some details, check the site linked here. It has details about blinking codes, and fault locating procedure, to many popular brand TVs and other devices.
http://electronicshelponline.blogspot.com/
If blinks continue without any pause, the main board is faulty.
Search the site by type in the "brand name" to your device, in the "Search box at the top right of the display window of the Homepage" to get gathered related posts.

Jan 11, 2017 | Sharp Televison & Video

1 Answer

I have a 60 inch sony tv that have a red flashing on the lower left side,no picture when I turn it on and there is ringing sound.


Those blinks [flashes] are fault indication (Error Codes). From the number of blinks occur at one time switch ON, you can get an idea about the faulty circuit section inside it. This will make repair easy. These are called blinking codes. Make sure about the exact number of blinking of the standby/power LED, by switching On & OFF the set, for at least two times. Count it carefully. If you wish to get some details, check the site linked here. It has details about blinking codes, and fault locating procedure, to many popular brand TVs and other devices.
http://electronicshelponline.blogspot.com/
If blinks continue without any pause, the main board is faulty.
Search the site by type in the "brand name" to your device, in the "Search box at the top right of the display window of the Homepage" to get gathered related posts.

Jan 09, 2017 | Sony Televison & Video

1 Answer

Insignia NS-51P680A12 TV won't turn on. I have a blinking light that I am sure is a trouble code, but I can't find the codes anywhere online.


Those blinks [flashes] are fault indication (Error Codes). From the number of blinks occur at one time switch ON, you can get an idea about the faulty circuit section inside it. This will make repair easy. These are called blinking codes. Make sure about the exact number of blinking of the standby/power LED, by switching On & OFF the set, for at least two times. Count it carefully. If you wish to get some details, check the site linked here. It has details about blinking codes, and fault locating procedure, to many popular brand TVs and other devices.
http://electro-medical.blogspot.com/

Jan 09, 2017 | Insignia Televison & Video

1 Answer

I have a HL67A750 Samsung no picture no sound blue light luminated on front 3 LEDs flashing


Those blinks [flashes] are fault indication (Error Codes). From the number of blinks occur at one time switch ON, you can get an idea about the faulty circuit section inside it. This will make repair easy. These are called blinking codes. Make sure about the exact number of blinking of the standby/power LED, by switching On & OFF the set, for at least two times. Count it carefully. If you wish to get some details, check the site linked here. It has details about blinking codes, and fault locating procedure, to many popular brand TVs and other devices.
http://electro-medical.blogspot.com/

Jan 05, 2017 | Samsung Televison & Video

Not finding what you are looking for?
Sony KP-46WT510 46" Rear Projection HDTV Logo

Related Topics:

45 people viewed this question

Ask a Question

Usually answered in minutes!

Top Sony Televison & Video Experts

kakima

Level 3 Expert

101516 Answers

The Knight
The Knight

Level 3 Expert

71611 Answers

Jerry Greenberg
Jerry Greenberg

Level 3 Expert

1646 Answers

Are you a Sony Televison and Video Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...