Question about Quintum Tenor D3000

1 Answer

Dear I am Getting FAS problem in my GATEWAY Axt 2400

Posted by on

  • Maximous2009 May 05, 2009

    Can you please tell me How to remove FAS from Quintum Tenor AF. I'm in deep trouble please help me to set the right settings so I dont get FAS.

    Thank you

×

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

Hi,
the CAS Signaling Line should to be checked, and make sure following parameter set correctly

Signaling Type=3
Tone Based Supervision=3
Answer Delay=120


Posted on Feb 05, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Now my comp.in the shack will not connect to my internet after installing swithch can connect with others fine


Make sure the comp in the shack is using the same gateway the others are using. It may be hard coded for a different gateway.

Open a command window, type "ipconfig /all" (without the quotes), then hit Enter. Look for the gateway line. Make sure it reads the same as the gateway on the computers that can connect. If it does, then look at the DNS lines, and make sure they're the same.

If you need more help, reply with the contents of this computer's ipconfig return, and one of the ones that can connect.

Jul 06, 2011 | SMC 5 x 10/100/1000Base-T LAN - Ethernet...

1 Answer

Pleased i need to download the remote management software (rmt) for cnet csh 2400 switch. where can i do this


Don't know about a special program, but you can try to use Centrastage (www.centrastage.com)
It's a remote management software and it seems like it can be useful for you.

Jun 29, 2011 | Cnet CSH-2400 (csh2400) 24x10/100 Mbps...

2 Answers

Dynex 4 port Hub


Try to assign an IP address to the second computer like 192.168.0.101 Subnet 255.255.255.0 and Default gateway 192.168.0.1

Note: This one is an example of IP address, the IP address that you need to assign is in range to the router that you have or with in range to the modem.

Mar 08, 2009 | Networking Hubs & Switches

2 Answers

IP Addressing by dhcp for vlans


tell each vlan about DHCP server using

ip helper <DHCP servers ip adddress>.

in config mode.

Mar 03, 2009 | Cisco Catalyst 2950 24x10/100 Mbps...

1 Answer

Hi, i need the gateway number for the d-link DES1008D can sombody tell me please how to find out the gateway number.


Hi,

The D-Link DES1008D is an unmanaged switch. Hence it does not have any gateway address and none can be set on it.

If you are looking for the gateway address of your computer, here's how to find it.

In Windows 2000 / XP / Vista / 7, Open command prompt and type in ipconfig

Look for the IP address of the default gateway.

eg:

C:\>ipconfig

Windows IP Configuration

Ethernet adapter Local Area Connection:
Connection-specific DNS Suffix . :
IPv4 Address. . . . . . . . . . . : 192.168.1.100
Subnet Mask . . . . . . . . . . . : 255.255.255.0
Default Gateway . . . . . . . . . : 192.168.1.1

Hope this helps.

Regards.

Jan 09, 2009 | D-Link DES-1008D 8-Port Ethernet Switch...

2 Answers

Dear I am Getting FAS problem in my GATEWAY Axt 2400 . Any Body solve this.


sorry.. quintum cannot solve the FAS problem..

only thing you can do is check the box were in it says less filtering

Dec 26, 2008 | Quintum Tenor D3000

1 Answer

Getting my acer on the internet.??


This maybe related to how your router is configured. Please try the following.

Click Start then All Programs then Accessories then Command Prompt. A new window will open. In that window enter the following (contains 1 space before /)--

ipconfig /all

In the response you should see for one adapter possibly of multiple adapters an

IP Address
Subnet Mask
Default Gateway
DNS Address(es) (one or more)

To work the following must be true

If the subnet mask is 255.255.255.0 then the first three numbers in the IP address and the Default Gateway should match (possibly 192.168.0 or something close). The last number should be different. There should be one or more non 0.0.0.0 DNS addresses. If this is not true please tell me what is wrong in a comment to this problem, I will respond with a solution. please provide your internet service providers name this may help me find his DNS servers for you.

One problem may be no DNS addresses -- this can either be configured into the router or the computer and should have been assigned by your internet service provider.

Assuming the above appears to be right then enter the following commands into the same window as before.
replace (default gateway) including parens with the address from above
may be like 192.168.0.1 with slightly different numbers

ping (default gateway)

It will either time out 4 times or respond with elapsed times.
If this does not time out you are connected to the other device successfully.

then try this command

ping www.google.com

if this comes back with an error like address not resolved or timeout we have other issues.

If it does not timeout or have an error you should be successfully accessing the internet and there may be a configuration issue with your browser and a proxy entered to work elsewhere.

Please respond to this request with additional information to allow us to find a final solution to your issue.

Dec 23, 2007 | Networking Hubs & Switches

1 Answer

How can I reset it back to original configration


Hey Eric, I do use same Avaya switch at my lab at office. To me what you have to do is quite simple, first of all you have to get from your network administrator the following info: - Free IP to assign to the switch - Subnet - Gateway (If you ping such IP from a machine of same subnet, there will not be an answer). Then log as superuser (#) and do this: 1. Type set interface inband Replacing , and with the VLAN, IP address and netmask provided by your network administrator and press Enter. (for VLAN you can list them and decide which one to use, but normally you should use 1) 2. Type reset and press Enter to reset the stack. 3. After the Reset, perform login again as superuser.  4. Type set ip route , replacing and with the destination and gateway IP addresses. (If you want all packets not from your subnet to be send to the gateway, then use 0.0.0.0 as destination, list routes set on device for more info) 5. Press Enter to save the destination and gateway IP addresses. That's all. Your switch will be rechable from your same subnet and from other networks if your gateway is working properly and there's no other element blocking you the access. Good Luck!

Oct 23, 2006 | Lucent Cajun P333T Networking Switch

Not finding what you are looking for?
Quintum Tenor D3000 Logo

Related Topics:

384 people viewed this question

Ask a Question

Usually answered in minutes!

Top Quintum Networking Hubs & Switches Experts

Mike

Level 3 Expert

4331 Answers

Les Dickinson
Les Dickinson

Level 3 Expert

18298 Answers

Brian Sullivan
Brian Sullivan

Level 3 Expert

27725 Answers

Are you a Quintum Networking Hub and Switch Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...