Question about Pioneer VSX-815-K Receiver

1 Answer

Pioneer vsx5700s a/v reciever display doesn't show

After turn it on, it works normally but the display doesn't show any thing [ doesn't have any light on the display ], it shows only LED in red on the volume control knob. please, send me cercuit diagram about this.
Thanks,
Chirasak,
26 Dec 2008

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Sergeant:

    An expert that hasĀ over 500 points.

    Champion:

    An expert who has answered 200 questions.

  • Expert
  • 247 Answers

You can buy the manual that you need from this websit:

http://www.user-manuals.com/advanced_search_result.php?keywords=vsx5700s+schematic&forward=plist&osCsid=be69c15232940a3899a73af57ea95f8a

please don't forget to rate this.

thanks

tom

Posted on Dec 26, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Hello - Our Pioneer vsx-305 display screen doesn't light up anymore and we are unable to get it to work even though the on/off button appears to operating correctly (red standby light comes on). T


It is likely failing due to age.Cold solders fail, corrosion can cut a connection, a capacitor can harden and fail... a myriad of things can happen in time. Repairing it will cost more than an inexpensive replacement. The same receiver can be had on ebay from $60 up (with shipping). It is a cost benefit issue at this point.

Jan 10, 2013 | Pioneer VSX-305 Receiver

1 Answer

My pioneer AV reciever last shows in the display a "amplifier error" then suddenly the power shut-off. aftr that i power on again but the reciever do not power on again. I remove all the...


The real problem is already informed you by the unit itself.
For us technician it was obvious that you have a faulty output I.C.
Your unit automatically shuts off to avoid further damaged most especially to the speakers.

I've advice you to look for a qualified technician/service center to replaced the output I.C.
After that your unit will back to normal again........

Jan 03, 2011 | Pioneer Audio & Video Receivers

1 Answer

Display shows overload and receiver shuts down


This means that one (or maybe more) of the amplifiers is shorted. Remove all speakers cables and try again. If you get the same message that means that one (or more) amplifiers is fried. To find which and why you will have to open the unit and test the amplifiers.

Jul 31, 2010 | Pioneer VSX-D412 Receiver

1 Answer

I have a vsx-52tx pioneer elite reciever with a light that keeps blinking. It keeps tripping while watching movies. should i get another one or is there something like resetting the reciever


I am assuming the light that is flashig is the "MCCAC" light on the front display. Supposing this is correct you have either a blown amplifier (one or mor channels) is the protection circuitry is not operating correctly. In either case the receiver has locked up to prevent any additional damage. There is a key sequience that needs to be preformed to unlock the unit so a technician can troubleshoot the problem. In most cases a blown amplifier should be in the $150.00 dollar range to get repaired. This is a fairly high end Pioneer receiver and is probably worth repairing, or at least finding out what the repair will cost.

May 03, 2009 | Pioneer VSX-1015TXK Receiver

1 Answer

Weird issue with Pioneer VSX-D510 and "tone"-setup


clean the all push buttons by using isoprpylalchohol.(surgical spirit)and dry well .i think all the buttons are short by itself.the problem is still there please check the power supplu secondary side smoothing condencers related to system control power section.

nuwan

Oct 02, 2008 | Pioneer VSX-D510 Receiver

1 Answer

How do i reset my Pioneer SX 316 Surround Sound System. i lost the owners manual.


1. Switch the reciever into standby.
2. While holding down the TONE button, press and hold the STANDBY/ON button for about three seconds.
3. When you see RESET? appear in the display, press the ENTER button. OK shows in the display.
4. Press SETUP to confirm.
OK appears in the display to indicate that the receiver has been reset to the factory default settings.

Aug 08, 2008 | Pioneer Audio & Video Receivers

3 Answers

Stand by button flashes but receiver wont turn on


I have vsx-d812 that has an AMP ERR in error menu. the troubleshooting was found to be Q696 and Q697 in the DC prot. area on "C" board, up near front toward diplay in center of c board. You can get access to error codes on VSX pioneer unit by pressing "enter" and "adv. surr." simultaneously for 2 sec. The display should show what error code you are experiencing. I believe there are three diff. error codes. 1) AMP ERR 2) OVERLOAD 3) BOAD ERR (not mistyped) I hope this helps pinpoint error code for ya.

Oct 07, 2007 | Pioneer VSX-816-K/S Receiver

4 Answers

Pioneer vsx-d307


You have a flashing "mute" on the display?...accordianman

Oct 04, 2007 | Pioneer VSX-D307 Receiver

1 Answer

Reciever display changing by itself


Sounds like a bad microcontroller. First check on the function selector knob if there is one and make sure it is not stuck - move or rotate it back and forth. Also, if the remote is nearby, try removing the batteries from it.

May 21, 2007 | Pioneer VSX-D511 Receiver

Not finding what you are looking for?
Pioneer VSX-815-K Receiver Logo

661 people viewed this question

Ask a Question

Usually answered in minutes!

Top Pioneer Audio & Video Receivers Experts

Steve Sweetleaf
Steve Sweetleaf

Level 3 Expert

1128 Answers

Ron Dufek
Ron Dufek

Level 3 Expert

398 Answers

gbob59

Level 3 Expert

2963 Answers

Are you a Pioneer Audio and Video Receiver Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...