Question about Computers & Internet

1 Answer

Cant open new eveready hard case lantern to put batteries in.

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

I waited until the next day and called the eveready battery cmpany and they said I didn't need to take the screws out - just turn the ring around the bulb and the whole front came off and we reached in and toook out the thing that held the batteres and place them in the holder! simple - when you know how! ha

Posted on Jan 03, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

What is the correct globe for the Eveready Model AV425 7 Watt U Tube lantern?


Hi, Check and clean the contacts from the batteries to the lamp.
There maybe corrosion in there. Also the switch maybe bad. Clean and retry. Use a bit of emery paper to clean contacts. good luck.

Jan 12, 2015 | Eveready Camping, Backpacking & Hiking

1 Answer

How do I change the bulb of the 6V Eveready Lantern if bulb won't come out


Drop a couple of drops of WD 40 on the bulb retaining ring. Let site overnight and in the morning it will easily unscrew. Note: be sure you use only a couple of drops as you don't want to get it on the reflective lense

Sep 27, 2014 | Energizer Eveready Utility Lantern Uses 6V...

1 Answer

How to fix the switch on eveready lantern flashlight


The switch in the lantern is a press fit switch so you will destroy it when you remove it. Remove the lense and retainer ring. Remove the battery. With a pair of pliers, preferably channel lock water pump pliers crush the switch into small piece and discard. Trail Tech makes the exact water resistant switch model 040-ls-b and you can get it at Amazon or on eBay . The switch runs around $6.25 + $4.00 shipping

Jul 11, 2014 | Energizer Eveready Utility Lantern Uses 6V...

1 Answer

How to test a flashlight bulb


To test a flashlight bulb you use an Ohm meter which will detect a broken filament or an open circuit within the bulb. If the bulb is bad it will read "OL" if it's good it will read "00.0"

Jun 14, 2014 | Energizer Eveready Utility Lantern Uses 6V...

1 Answer

How to connect a spring pole 6v battery


Inside the case of the light, there will be 1 wire with a tapered notched connector. Take the connector with the low end of the taper and push it into the negative (-) spring (in between the coils ) of the battery. The spring will wedge the connector it one of the notches and will hold it securely. Reattach the lense carefully seating the end of the bulb onto the positive (+) spring of the battery.

May 25, 2014 | Energizer Eveready Utility Lantern Uses 6V...

1 Answer

Replacing a 6 volt battery


Check that the contacts where the springs on the battery make contact in the light to see if they are corroded. If so scrape or sand them off.

Jan 09, 2013 | Energizer Eveready Utility Lantern Uses 6V...

1 Answer

I have bought a new 6volt battery for my dolphin but can't work out how to replace it.


The bezel (the circular portion on the front of the flashlight that holds the bulb and lens) will unscrew. The old battery should slide right out.

Hope this helps.

Apr 07, 2011 | Energizer Eveready Utility Lantern Uses 6V...

1 Answer

How do I change the bulb of the 6V Eveready Lantern?


If it is the yellow floating lantern you have to remove the black plastic stub on the underside of the reflector using needlenose pliers to wiggle and slightly pull until it releases and the bulb will come out.

Jan 06, 2011 | Energizer Eveready Utility Lantern Uses 6V...

1 Answer

I have an Eveready fluorescent lantern #9209. I can't figure out how to put the batteries in. I get the back compartment opened but am completely flummoxed after that. Does anyone have the instructions?...


On the bottom is an indention where the lamp attachs to the handle portion. The latch opens when you push the button toward the front of the lamp. Once it is opened, then slide the lamp off, revealing the battery compartment - remove the batteries and replace with new ones

Dec 28, 2010 | Craftsman Camping, Backpacking & Hiking

2 Answers

Replacing batteries on Energizer Hard Case Lantern


If you have the Energizer Hard Case Lantern TUF4D1, simply grasp the whole front of the lamp piece (including the rubber cover), and twist in a counter-clockwise direction to remove. Then squeeze together the two black tabs and pull the battery compartment out to replace the batteries.

Jul 05, 2010 | Energizer Eveready TUF4D1E 4D Cell Lantern

Not finding what you are looking for?
Computers & Internet Logo

Related Topics:

47 people viewed this question

Ask a Question

Usually answered in minutes!

Top Computers & Internet Experts

Brian Sullivan
Brian Sullivan

Level 3 Expert

27725 Answers

kakima

Level 3 Expert

102366 Answers

David Payne
David Payne

Level 3 Expert

14161 Answers

Are you a Computer and Internet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...