Question about Computers & Internet

1 Answer

Have power cord plugged into asus eee machine and wall outlet. light has been blinking all day. when asus eee gets unplugged it shuts off.

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Scholar:

    An expert who has written 20 answers of more than 400 characters.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 100 Answers

Lets try this ---

* turn of your computer
* remove the plug from your computer.
* Remove the battery from your computer
* Let it sit for 3-5 minutes
* Replace the battery
* Plug your computer back in (Make sure the wall outlet is working as well, seems simple, but have seen it before)
* Let it sit for about 3-5 minutes
* Boot your computer
* go to
Start -> Control Panel -> Power Options -> Power Meter
Note the Total Battery Power Remaining

* Let your computer sit for 15-30 Minutes and see if the Total Battery Power Remaining has gone up.

If so problem solved

if not you may be time for a new battery.

Posted on Dec 26, 2008

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Charger seems to have both red and green lites flashing at the same time no sequence and both batteries connected read 4.0 VDC, are these chargers repariable or throw aways


Your manual is here. The section on charging states, that green blinking means your battery is fully charged but blinking red means that your charger is faulty. I would say repairable.

1. Plug the female connector of the AC power cord (supplied) to the AC receptacle on the charger and plug in the male connector on the AC power cord into the wall outlet.

2. The On/Off LED indicator is blinking RED, this is abnormal. Unplug AC power cord from the on-board battery charger and wall outlet. Charger may need to be replaced. Contact an Invacare dealer or qualified technician.

3. When the On/Off LED indicator light is Off, charger is Off.

4. When the Charge LED indicator light is YELLOW, the batteries are charging.

5. When the Charge LED indicator light is solid GREEN, the batteries are fully charged (as their condition will allow).

6. When charging is complete, unplug the male connector of the AC power cord from the wall outlet and then unplug the female connector of the AC power cord from the AC receptacle on the charger.


http://www.invacare.com/doc_files/1125085.pdf

http://www.invacare.com/doc_files/1125085.pdf

Mar 24, 2016 | Invacare Pronto M51 Power Wheelchair

1 Answer

I have a panasonic 50" model TC-50S1 i turned it on and the picture was messed up it then shut off and the red light keeps blinking one time


Try unplugging any HDMI cables from the TV and plugging the TVs power cord into a different wall outlet.

Nov 03, 2013 | Televison & Video

1 Answer

HOW TO SOLVE PRINTER ERROR WITH BLINKING LIGHTS


Unplug the power cord from the wall outlet.

Unplug the power cord from the all-in-one.

Wait 30 seconds and plug the power cord back into the wall outlet.

Press the Cancel and Right Arrow buttons.

While still holding the buttons, plug the power cord back into the all-in-one. Continue to hold the buttons for two seconds, and then release them.
Use the On button to turn the power off and then back on again.

If you need any kind of technical assistance you can contact support cell at http://www.vtechsquad.com/

Jan 30, 2013 | Epson Stylus Photo Px660

1 Answer

Hello, I have a problem with my eee 100H5 netbook. I was using it connected to the power outlet, when it randomly shut off. It cannot be restarted and is unresponsive to the power cord, meaning that the...


Unplug the computer and take out the battery.
Hold the power button for ten seconds.
Leave the battery out and plug in the power cord.
Press the power button.
If the computer turns on, put the battery and everything should now work.
This has solved every "laptop not turning on problem" for me and my friends.
sublimedjg

Jun 23, 2011 | ASUS Eee PC 1000HE Netbook

1 Answer

There is no power when i press the power button for the PC. The light for the power adaptor is showing a blue color i believe is the normal color. your help appreciated


Normal steps to take when diagnosing power issues are as follows: 1. Ensure that the battery is seated properly into the bottom of the machine. To check press the slider buttons that release the battery, pull it out, put it back in and make sure it locks. 2. Check that the cord from the wall to the AC Adapter box is pushed in tight. Sometimes they get pulled out slightly and then no power goes to the laptop. 3. Make sure that the outlet that the power cord is plugged into is providing power. Plug another device into that outlet and see if it gets power, if it doesn't then your outlet is bad or you tripped a breaker. If the device powers on then your AC adapter may be bad on the netbook.

Dec 29, 2009 | ASUS Eee 4G Notebook

1 Answer

Hp deskjet 940c - all 3 light are blinking


Check this page...

http://h10025.www1.hp.com/ewfrf/wc/document?docname=bpd09170&cc=us&lc=en&dlc=en&product=59129

"Here's what it says is the solution for all 3 lights blinking.
  1. Turn the printer off. Unplug the power cord from the back of the printer. Unplug the power cord from the wall outlet.
  2. Wait 30 seconds. Plug in the power cord to the wall outlet. Plug in the power cord to the back of the printer.
  3. Turn the printer on.
If you have completed all of the steps listed above and are still experiencing a problem, service your product."

Dec 23, 2009 | HP DeskJet 940c InkJet Printer

2 Answers

Sony KV-34HS420 shuts of and stand-by light blinks


  1. Turn off the television. IMPORTANT: For a projection television that uses an internal lamp, wait 5 minutes after turning off the television to allow the lamp to cool before continuing with the following steps.
  2. Unplug the television power cord from the electrical outlet.
  3. Let the television remain without power for 60 seconds.
  4. Plug the power cord back into the electrical outlet. NOTE: If the television is plugged into a power strip or surge protector, remove it from the power strip or surge protector and plug it directly into the wall outlet. If the issue is resolved, the problem is with the power strip or surge protector and not the television.
  5. Turn on the television.
If the issue is still unresolved after following all of the troubleshooting steps, service may be required. Please note the number of times the STANDBY light flashes and relay that information to the service center.

Source

Sep 01, 2009 | Sony FD Trinitron WEGA KV-34HS420 34" TV

1 Answer

Sunbeam 4267-000 not turning on just blinking red


"FF" or a blinking light will display meaning “Fault Found”. The “fault” is in the amount of power available to the blanket, mattress pad or throw.
There are several causes to this problem:
1. Bedding product is plugged into an extension cord, surge protector, power strip, or not plugged into a direct wall outlet.
2. Bedding product wasn't plugged in properly.

To FIX this problem, do the following to reset your bedding product:
1. Unplug the power cord from the electrical connection.
2. Unplug the cord from the actual bedding product itself.
3. Re-plug the cord into the bedding product. Make sure the connection is secure and complete.
4. Re-insert power cord back into a wall outlet.

If the 4 steps above are not followed in order, the bedding product will not properly reset.

Dec 08, 2008 | Sunbeam 4237 / 4238 Iron with Auto...

1 Answer

Zvonko jelusic from belgrade


The print carriage is stuck.

Solution

  1. Open the top access door on the printer.
  2. Remove the print cartridges.
  3. Close the print cartridge flaps after removing the print cartridges.
  4. Turn the printer off and then on again.
  5. Replace the print cartridges.
  6. Close the top access door.
If the resume light continues to blink after the print cartridges are released,

OR

the print carriage is stuck or makes a grinding noise, follow these steps.

Solution

  1. Lift the top cover to the printer.
  2. Turn the printer off and then on again.
  3. Unplug the power cord from the back of the printer when the grinding noise starts. Unplug the power cord from the wall outlet.
  4. Move the print carriage towards the middle of the printer (this procedure may take a couple of tries to get the timing correct).
  5. Take out the print cartridges and close the top cover.
  6. Plug the power cord into the wall outlet. Plug the power cord into the back of the printer.
  7. Open the top cover, reinstall the print cartridges, and then close the top cover
Solution

  1. Open the top cover.
  2. Unplug the power cord from the back of the printer. Unplug the power cord from the wall outlet. Wait a minute or so.
  3. Plug the power cord into the back of the printer. Plug the power cord into the wall outlet

Sep 22, 2008 | HP DeskJet 5550 InkJet Printer

13 Answers

My Sunbeam electric blanket controls blink when I plug the control cable into the blanket. I cannot turn the controls on or off.


Same problem, but now it is ok.  I emailed Sunbeam and was told that if my blanket was not plugged directly into a wall outlet it was not getting enough power and I needed to plug it into a wall outlet taking these steps:
1) Unplug from the surge protector/extension cord 2) Unplug from the blanket 3) Plug back into the blanket 4) Plug into a wall outlet

Jul 21, 2008 | Heating & Cooling

Not finding what you are looking for?
Computers & Internet Logo

Related Topics:

85 people viewed this question

Ask a Question

Usually answered in minutes!

Top Computers & Internet Experts

Brian Sullivan
Brian Sullivan

Level 3 Expert

27725 Answers

kakima

Level 3 Expert

102366 Answers

David Payne
David Payne

Level 3 Expert

14161 Answers

Are you a Computer and Internet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...