Question about Belkin F5D7230-4 Kit (F5D7230V4SNPDQ)

1 Answer

Forgotten network key to log on to secured wireless g router

I have recentley had ro reformat my hard drive,s dropped my connection to wireless g router,my pc can stil see it but i cannot connect because i cant remember the password i set, how do i silve this, please help

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

Password recovery isn't really possible. Pushing the rest button in the back for a few seconds will reset the router to factory defaults. You will need to reset all the wireless security and such so best to do this with a pc connected directly to it. Default IP for it if you have changed it is 192.168.2.1.

Posted on Mar 25, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

WIRELESS GATEWAY


How to View or Change Your Wireless Network Password


Symptoms:


You have lost or forgotten the password to your wireless network
You have lost or forgotten the password for the router, access point or other network device
You left the default password or used a weak password and someone has hijacked your network



Depending on the router, you can either view or reset the wireless network password (also referred to as the passphrase or security key) if you can log into the router. Some routers mask the wireless network password, so while you cannot recover it, you can enter and save a new password.


If you cannot log into your router because you have forgotten the router password or your network has been hijacked, please refer to "Lost or forgotten password for router or other device" below.


To view or reset a wireless network password:


Launch your Internet browser and type http://www.routerlogin.net in or http://192.168.1.1 or http://192.168.0.1 the address field for your browser. Enter the router's username and password.
The default username is admin, the default password is password.
From the left-hand navigation menu of the Router administration interface, select Set Up > Wireless Settings
Note: On some routers this option will be under BASIC > Wireless.
From the center screen, you find the current wireless security settings under the Security Options heading.


If the wireless network passphrase is visible, review it and use it to log devices onto your network.
If it is not visible, you can change your wireless passphrase; however, changing the passphrase will cause you to lose your wireless connection. Connect your computer to the router with an Ethernet cable before entering a new passphrase into the text box and clicking Apply.


Read more about Securing your Wireless Network.
If you cannot log into your router:


- If you were routed to the NETGEAR website or getting the "Page cannot be displayed" message when trying to login to router, make sure you are connected to the NETGEAR router. Check your wired connection and make sure cable is securely plugged in and LED is on. If wireless adapter is on, make sure you are NOT connected on a different wireless network.


- Unfortunately, there is no way to recover a lost or forgotten password from a router or access point; you will need to reset the device to factory defaults. However, once the device is reset to factory defaults, you can use the default access information to reconfigure your router settings. NOTE: Restoring factory defaults on a device will erase any customizations you have made. You will lose any configurations saved to the device!


See the following articles for more information:


Secure Your Wireless Network: WPA/WPA2 (Recommended)
Reset and Restore a NETGEAR device to Factory Default Settings
Default Password for NETGEAR devices

Jul 19, 2012 | Gateway Routers

Tip

Tip to retrieve if you forget the wireless key of your router


Welcome to fixya

If you have forgotten the wireless network key , you can retrieve it from the router itself

Click the below link
http://192.168.1.1

Now it will ask for username and password

Enter username = ( blank) and password = admin
If you can't login using this credentials then you will have to reset the router

If you logged in . Then click on Wireless > Wireless security

On this screen you can see the wireless key

If the security mode is WEP then your password is Key1
If the security mode is WPA-PSK then your password is WPA Preshared key

Thanks

on May 04, 2011 | Routers

1 Answer

Trying to connect wirelessly to 2 wire. I get limited access icon


Hi groveland1,

I see that you are having issue with your Internet Connection, Limited or no connectivity is a possible issue with your network key / security key on the router and your laptop.

1. Try and check the network key in your router.

2. Check your network settings in the Laptop and see if the security settings in your Laptop is the same as the security/network key in your Router.

3. If possible recreate your wireless connection in windows for a fresh connection from your Laptop to your Router.

4. Change your Network Key in the Router and in your Laptop see if it will connect in-case you may have forgotten you old Network Key.

Hope this helps.

Apr 04, 2011 | 2wire (1000-400108-001) Router

1 Answer

I'm trying to sign into my Netgear Router to reset my password, because I do not remember it and to set-up a secure connection. However whenever I type in http://routerlogin.net, All I get is information...


How to View or Change Your Wireless Network Password Symptoms:
  • You have lost or forgotten the password to your wireless network
  • You have lost or forgotten the password for the router, access point or other network device
  • You left the default password or used a weak password and someone has hijacked your network

Depending on the router, you can either view or reset the wireless network password (also referred to as the passphrase or security key) if you can log into the router. Some routers mask the wireless network password, so while you cannot recover it, you can enter and save a new password.

If you cannot log into your router because you have forgotten the router password or your network has been hijacked, please refer to "Lost or forgotten password for router or other device" below.

To view or reset a wireless network password:

  1. Log in to your NETGEAR router by browsing to http://www.routerlogin.net or http://www.routerlogin.com. Enter the username (admin) and password. By default, the password is password or 1234 unless it has already been changed.
  2. From the left-hand navigation menu of the Router Manager, select Set Up > Wireless Settings.
  3. From the center screen, select your encryption type from under the Security Options heading.
    • If the wireless network passphrase is visible, review it and use it to log devices onto your network.
    • If it is not visible, you can change your wireless passphrase; however, changing the passphrase will cause you to lose your wireless connection. Connect your computer to the router with an Ethernet cable before entering a new passphrase into the text box and clicking Apply.
If you cannot log into your router:

Unfortunately, there is no way to recover a lost or forgotten password from a router or access point; you will need to reset the device to factory defaults. However, once the device is reset to factory defaults, you can use the default username ("admin") and password (either "password" or "1234" depending on your router) to reconfigure your router settings.

NOTE: Restoring factory defaults on a device will erase any customizations you have made. You will lose any configurations saved to the device!



If you have changed the default password and have forgotten the password, you may need to reset the NETGEAR device to factory default settings.

When a NETGEAR device resets, it goes back to the state when it was new - all information that was entered by hand is lost! Examples include critical things you need to get online, such as ISP username, ISP password, IP addresses, wireless security keys, and ports and services that were opened. It all needs to be re-entered.
So, have your ISP information before resetting the router.
Naturally, if you moved to a new city, or if you bought a used router, the old information in the router may not be of use to you. Contact your ISP if you can't connect any computer directly to the Internet. Then, if there is a connection problem when the router is added, see No Internet Access Through the Router
Reset for most routers with a reset button on the rear panel
Write down configuration information such as IP addresses, security keys, opened ports and services, etc., that you modified. (The default username is admin and the password is either password or 1234. Try these before resetting the router.)

  1. Press the reset button on the back until the test light blinks. This takes about 10 seconds. (To avoid accidental resets, the small button is recessed. Use a pen or paperclip to access it.)
  2. Release the button.
  3. Wait for the router to reboot.
  4. Log in with the default password. If the router configuration was not cleared, try these additional steps AFTER the router has finished rebooting.
  5. Unplug the router's power.
  6. Press and hold the reset button. While the button is held down, reconnect router's power.
  7. Continue to hold the reset button for 20 seconds after reconnecting the power.
  8. Wait for the router to reboot.
  9. Log in with the default password.
For DGN2000 / DG834Gv5 Routers
To restore the factory default configuration settings when you do not know the login password or IP address, press both the Wireless button and WPS button on the side of the modem router for 5 seconds.
For FR314, FR318, and FV318
These routers require reloading the firmware in order to recover from a lost password. Download the most recent firmware from NETGEAR's Web site before proceeding. Follow the instructions in the manual.
For routers with a 9-pin manager port on the rear panel: RT314, RT311, RM356, RT328, RT338, RH340, and RH348
See Updating Router Firmware That Uses a Manager Port.
This applies to:
  • All NETGEAR devices
Related articles:



Mar 26, 2011 | NetGear WGR614 Wireless Router

1 Answer

My Atheros AR5007 will only complete a "Local Connection, No Internet Connection" to a NetGear N600 Dual Band Router when Security Options (WPA2-PSK (AES)...ect) are selected on the Wireless...


Since the connection works without the encryption settings, it is NOT a driver issue. It sounds like a missing wireless network security setup problem. So assuming Windows (Mac OSX is similiar):

  1. Connect a laptop/PC to the NetGear via ethernet. It saves on some aggravations later.
  2. Connect to the NetGear and restore the security settings, and remember your keyword.
  3. On your computer, open the list of Wireless Networks (usually Start->Control Panel->Network(ing)->Wireless Networks). The menu sequence might differ slightly, depending on which Windows you're running.
  4. Find and click on "Manage Wireless Networks" (or words to that effect)
  5. Right click on your wireless network's name to get the drop down menu, and select "Properties"
  6. Find a button or tab related to "Security"
  7. Under Security Type, select WPA2-PSK (or Personal)
  8. Under Encryption Type, select "AES"
  9. Under Password (or Security Key), type in your router's WiFi security key word. You may have to log back into the NetGear and find the keyword (yours) or the alternate (gibberish) form.
  10. Save the settings
  11. If you're connected to that wireless network, then disconnect
  12. Try connecting to the wireless network again. It should work this time.

Feb 23, 2011 | D-Link Routers

2 Answers

I have forgotten my security key for connecting to the internet with my netgear wireless router


Log in to your NETGEAR router by browsing to http://www.routerlogin.net or http://www.routerlogin.com. Enter the username (admin)and password by default the password is 1234 unless it has already been changed
from the left-hand navigation menu of the router manager,select wireles set up>wireless settings
from the center screen,select your encrytion type from under the Security Options heading
if the wireless network passphrase is visible,review it and use it to log on devices onto your network.
If it is not visible you can change your wireless passphrase but changing your passphrase will cause you to lose your wireless connection
Connect your computer to the router using an Ethernet Cable before entering a new passphrase into the text box and clicking apply.
If you cannot log into your router:Unfortunately, there is no way to recover a lost or forgotten password from a router or access point; you will need to reset the device to factory defaults. However, once the device is reset to factory defaults, you can use the default username ("admin") and password (either "password" or "1234" depending on your router) to reconfigure your router settings.

Restoring factory defaults on a device will erase any customizations you have made. You will lose any configurations saved to the device!

From the center screen, select your encryption type from under the Security Options heading.

If the wireless network passphrase is visible, review it and use it to log devices onto your network.

If it is not visible, you can change your wireless passphrase; however, changing the passphrase will cause you to lose your wireless connection. Connect your computer to the router with an Ethernet cable before entering a new passphrase into the text box and clicking Apply.

hope this helps

Nov 11, 2010 | NetGear Wireless router EN Fast EN

2 Answers

I have forgot my wpa security password,i have tryed to reset my router,but im not having much luck,cause i dont understand it all.when i follow the instrsuctions what the person onm line tells me to do,i...


How to View or Change Your Wireless Network Password Symptoms:
  • You have lost or forgotten the password to your wireless network
  • You have lost or forgotten the password for the router, access point or other network device
  • You left the default password or used a weak password and someone has hijacked your network

Depending on the router, you can either view or reset the wireless network password (also referred to as the passphrase or security key) if you can log into the router. Some routers mask the wireless network password, so while you cannot recover it, you can enter and save a new password.

If you cannot log into your router because you have forgotten the router password or your network has been hijacked, please refer to "Lost or forgotten password for router or other device" below.

To view or reset a wireless network password:

  1. Log in to your NETGEAR router by browsing to http://www.routerlogin.net or http://www.routerlogin.com. Enter the username (admin) and password. By default, the password is password or 1234 unless it has already been changed.
  2. From the left-hand navigation menu of the Router Manager, select Set Up > Wireless Settings.
  3. From the center screen, select your encryption type from under the Security Options heading.
    • If the wireless network passphrase is visible, review it and use it to log devices onto your network.
    • If it is not visible, you can change your wireless passphrase; however, changing the passphrase will cause you to lose your wireless connection. Connect your computer to the router with an Ethernet cable before entering a new passphrase into the text box and clicking Apply.
If you cannot log into your router:

Unfortunately, there is no way to recover a lost or forgotten password from a router or access point; you will need to reset the device to factory defaults. However, once the device is reset to factory defaults, you can use the default username ("admin") and password (either "password" or "1234" depending on your router) to reconfigure your router settings.

NOTE: Restoring factory defaults on a device will erase any customizations you have made. You will lose any configurations saved to the device!

See the following articles for more information:

Nov 07, 2010 | NetGear WIRELESS-G WGR614 802.11G WIRELESS...

2 Answers

SECURITY


log in to the router setup page.... you can type 192.168.2.1 in IE to open the setup page...on the left side you ll find an option called security below wireless heading...click on that and change the security mode to 64bit WEP....in the key1 you need to enter a 10-digit number (5pairs)as the security key for your wireless network...donot enter anything in any other boxes....click on apply changes....now close the IE...go to network connections and delete all preferred networks from your computer....now scan and connect again....it ll ask for a password...enter the security key and get connected....

Mar 23, 2010 | Belkin Wireless G Plus MIMO (F5D9230-4)...

1 Answer

I cant connect thru my netgear router model wgr614v7


If you hook your PC directly to the router using an Ethernet cable you don't need the key. You can log into the router and change the WEP Key to anything you want, but u have to be directly connected to the router not going through the wireless.

Jan 25, 2009 | NetGear WGR614 Wireless Router

1 Answer

Internect connecting


If the laptop was connecting wirelessly before and you didn't change the wireless security key on the router during your troubleshooting steps with the ISP then it should just reconnect. If it doesn't reconnect you should probably delete the wireless profile that's saved and try connecting again. When you delete the wireless profile you will have to enter the security key again. Make sure you have this information handy.

If you are uncertain what the wireless security key is use your desktop that is physically connected to the router to log into the router and reset the security key.

To log onto the router you need to know the routers IP Address. You can obtain that information through the following:

START MENU
RUN
Type CMD
Click OK
Type IPCONFIG
Hit Enter
Look for the default gateway. The default gateway is the IP Address of the router. By default the IP is 192.168.1.1.

Type whatever IP Address you discovered into the address bar of your web browser (Internet Explorer for most) and hit enter.

You will be prompted for a login. If you didn't change the default login information to the router it should be a blank username and the word: admin - as the password.

Navigate to the wireless settings and reset the security key.

From your laptop key in the new network key.

Hope this helps.

MO

Jul 18, 2008 | Linksys Wireless-G WRT54GS Router...

Not finding what you are looking for?
Belkin F5D7230-4 Kit (F5D7230V4SNPDQ) Logo

223 people viewed this question

Ask a Question

Usually answered in minutes!

Top Belkin Routers Experts

Les Dickinson
Les Dickinson

Level 3 Expert

18304 Answers

steve morris
steve morris

Level 3 Expert

1673 Answers

Christopher Thrash

Level 3 Expert

425 Answers

Are you a Belkin Router Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...