Question about Audio Players & Recorders

1 Answer

I have a Pioneer audio-video stereo receiver and when i turned it on last night,,the led lights didnt come on. There is power to it and all other funtions seem to work fine....Any ideas??? thanks Happy Holidays to you all...

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 624 Answers

Can you please tell me what model number of Pioneer you have. All Pioneer receivers are not the same. In fact, most model numbers are different from all the other model numbers. The problem one model may have, will most likely not be the same thing that causes that problem in a different model number.

Posted on Feb 06, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have an RCA STA 3900 stereo reciever that wont turn on. Standby light is on. Tried resetting it from the back but didnt work. Please advise


A standby condition can mean a fault in the receiver. voltages in the system are off. This can either be a bad diode or power transistor.

Aug 24, 2014 | RCA Sta-3900 Stereo Receiver

1 Answer

Pioneer vsx-01 receiver, standby light burned out. Button works fine, just no blue light. Pioneer sells a replacement standby button......is this easy to install and will it solve the problem? Do you have...


the light is an ledt they very rarely go bad ..to confirm its bad you must first see that the led is getting power --a voltmeter one end to the frame of the unit and the other to either lead on the led will confirm if its bad or not a typical led will run on or near 3 volts dc... if theres no power at the led than the problem is elsewhere

Aug 30, 2010 | Pioneer Elite® VSX-01TXH 7.1 Channels...

1 Answer

I have a Pioneer Audio Multi Channel Receiver model SX-316-S and I can't seem to figure out how to hook up my TV and DVD to the receiver so that all sound comes through the receiver


DVD audio straight in from its highest quality audio output. Use the stereo audio output to run straight to the TV for casual watching through TV speakers without the Pioneer involved.

A TV is just a glorified night-light, not a sound source - get its related audio from the Cable Box, ditto the highest quality

Mar 04, 2010 | Pioneer SX-315

1 Answer

Power wont come on at all


May be the power supply check for power to the power supply and the output voltage from it as well !! May need to be replaced ! It cost $125.00 for part and $225.00 for a new one installed !!

Jul 21, 2009 | Denon AVR-1506 Receiver

2 Answers

Pioneer power LED is Blinking


If that didn't work, with the power off try holding Tune + and Auto surround/stream direct buttons for a few seconds to reset the protection circuits. Make sure to keep 8" of empty space above the unit for air, as overheating can cause this problem. If it fails again, there could be bigger problems, so get it checked

Mar 29, 2009 | Pioneer VSX-918V Receiver

1 Answer

LED light dont come on!!! Pioneer audio receiver VSX-9700s


Do you mean that the display that show the audio source or mode doesn't turn on? Try shining a bright flashlight at the display and see if you can read it. If you can, then the backlight light bulbs have died.

Replacing it will be a pain but you may find a usable replacement at Radio Shack. Just measure the voltage that goes to the bulbs and find one with similar ratings. They are probably 12v lamps.You will need to remove the display from the front panel of the amp and desolder the old lamps. Getting at the bulbs is the hardest part.

Dec 25, 2008 | Audio Players & Recorders

1 Answer

Will not turn on.


LLLLLAAAAAAZZZZZZAAAAA

Sep 25, 2008 | Pioneer VSXD814 Receiver

1 Answer

Pioneer VSX 915 powe off


Had a power surge last night and got the same problem. Unit wont power on and has a blinking blue light on standby button. I found the solution from the service manual for a similar model.

Hold down ENTER and ADVANCED SURROUND buttons.

This resets the DC overvoltage sensor and bingo the unit comes back to life again.


Jun 18, 2008 | Pioneer VSX-915 Receiver

2 Answers

Pioneer SG-9500 Equalizer Power Led Replacement?


A generic LED will work just fine. Be sure to match polarity...accordianman

Mar 09, 2008 | Audio Players & Recorders

2 Answers

Not turning on


Could be power supply, fuse... Did you chech this?

Oct 08, 2007 | Pioneer VSX-52TX Receiver

Not finding what you are looking for?
Audio Players & Recorders Logo

Related Topics:

37 people viewed this question

Ask a Question

Usually answered in minutes!

Top Audio Players & Recorders Experts

kakima

Level 3 Expert

102366 Answers

 Grubhead
Grubhead

Level 3 Expert

4852 Answers

The Knight
The Knight

Level 3 Expert

72620 Answers

Are you an Audio Player and Recorder Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...