The HDMI inputs are pass through inputs only. The reciever cannot recieve any sound signals through the HDMI's. The reciever acts as a selector switch for the HDMI inputs only. Whatever input you have selected on the reciever is the one that is being sent through the output to your TV. The "unlock" display shows when there is no sound signal sent to the reciever. There is no code to unlock. This is the reciever's way of telling you that there is no sound being sent to it from that input. Since there is no sound being processed from the HDMI's, you need to hook up an additional audio cable from the device to the reciever (preferrably an optical cable). When the reciever recieves an audio signal, it will then "unlock". I know it is confusing. I had to look into this problem myself, so I'm happy to help. Higher end recievers will actually recieve and process sound signals from the HDMI's. When I bought this one I thought it was going to do the same. That's what I got for trying to save a couple bucks on the cheeper model! Although it is still a good reciever.
STRDG520 : From what I figured out the use of BD for input but no digital optical cable is connected. I had to use the DVD HDMI connection and the Digital coaxial to get the sound from the Amp. for My HDMI satellite connection. Hope this helped
- If you need clarification, ask it in the comment box above.
- Better answers use proper spelling and grammar.
- Provide details, support with references or personal experience.
Tell us some more! Your answer needs to include more details to help people.You can't post answers that contain an email address.Please enter a valid email address.The email address entered is already associated to an account.Login to postPlease use English characters only.
Tip: The max point reward for answering a question is 15.
hi you can use codes to unlock your mobile ,because it mainly reduce the strain ,to get the codes you can visit here mobile-unlocker here you select the country from where you brought the mobile and the provider to which your mobile is locked then they ask the imei number of your mobile finally they will render you the unlock codes at reasonable cost.
If your phone displays the 'Insert correct simcard' then your phone is currently locked to particular network. You need to unlock to use it with other network. There can be many ways to Unlock your phone. As far as i know unlocking by codes is the simple and safe way. I will suggest the website Unlock-zone.com which is doing good service and they were recommended highly in the cell phone forums. I used them to unlock my cell phone. contacted them and within 30 mins i had my unlock code and my phone was unlocked. Hope this helps.
Press the P.Scan and RBDS buttons simultaneously and hold
until "1000" shows on the display. Release the buttons. Do NOT press
these buttons again, otherwise the radio will consider "1000" to be the
Use Preset buttons 1 ... 4 to enter the four-digit code
number from your radio card. Preset button 1 corresponds to the first
digit, Preset button 2 corresponds to the second digit, etc. Each press
of the button increments the number by 1.
Once the code shown on the display is correct, press the
P.Scan and RBDS buttons simultaneously and hold until the word "SAFE"
appears in the display, then release the buttons.
The radio should unlock and be usable shortly afterwards.
If an incorrect code is entered, the word "SAFE" appears,
first flashing and then continuously. You can repeat the above steps to
unlock the radio once more, the number of attempts will be shown in the
display. If an incorrect code is entered again, you radio will be
locked for about one hour. After one hour - the radio must stay on and
the key must remain in the ignition lock - if the display goes out, the
you can repeat the above procedure to unlock again. The cycle - two
attempts, one hour lock-up - still applies.
If you lose your radio code, contact your Audi dealer.
Turn on radio - the word SAFE will appear in the display. Press th P.SCAN and RBDS buttons simultaneously and hold them down until "1000" lights up in the display.Release buttons.Do not, under no circumtances, continue holding them down or press them once again. This will cause the radio to consider the number 1000 to be the input code.Use station buttons 1,2,3,and 4 to enter the code number on your Radio Card. Use the button 1 to enter the first number 2 for the second number 3 for the third number and 4 for the last number.Once you have entered the code and it shows on the display,press the P.SCAN and RBDS buttons down again simultaneously and hold them down until the word SAFE appears in the display.Release buttons. Soon afterwards a frequency will be displayed.
According to Kenwood's car audio FAQ, the stereo needs to be brought to a Kenwood service center to be decoded. You may run into a problem, however, as Kenwood requires a receipt or other proof of purchase in order to prove you are the rightful owner of the radio.
Good luck, I hope this was helpful, even if it maybe wasn't the answer you would like to hear.