Question about Polk Audio Monitor 50 Main / Stereo Speaker

1 Answer

Polk Audio Monitot 50s

I just moved and my 50s just got trashed. I need to replace all the speakers in the cabinet and I need two covers and four feet. Should I throw them away???

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 5 Answers

Cost about $360 new. Will have to check with Polk regarding the drivers. Close call. http://www.polkaudio.com/support/dealer_sales_refunds.php

Posted on Apr 21, 2007

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Hi my creature 3 speakers were used at a party and the subwoofer dropped a couple times off about a 2 feet high table. now whenever i try to play music from my computer theres a loud buzzing noise in the...


A wire inside the cable has probably come loose, unless you (or a friend) have decent soldering skills to just replace the wire form the audio controller (most likely spot to have problems) to the PC they are probably just trash.

May 17, 2011 | JBL Creature III 2 Speakers

1 Answer

Hi, I bought a house with some Niles HD 6 speakers and need to move them down the wall to install a new cabinet. I can't work out how to remove them from the wall to install them lower?


First remove the wire mesh grill with a curved pin or lever it out with a sharp kitchen knife. Then you will notice four black screws very close the groove into which the grill fits.Using a correct size + screwdriver unscrew all the four screw anticlockwise till you feel the whole speaker panel shake loose. Make sure somebody is holding the outer frame while you are doing it or it might suddenly fall. The are red and black spring clip connectors for the speaker wires. Disconnect them foe removing the speakers completely.

Mar 10, 2011 | Niles HD6 Main / Stereo Speaker

1 Answer

HOW DO YOU REPLACE THE DOOR LOCK I NEED TO KNOW HOW TO GET AT THE LOCK THE WASHER ONLY LOCKS IF YOU HOLD IN ON THE TOP OF THE DOOR


Disconnect power then open the dispenser cover and remove the four screws securing the dispenser bezel to the top cover then lift the bezel off. The top cover with the dispenser bezel off can be lifted to the rear of the machine to access the door locking mechanism, but you have to remove the front panel first.

Open the machine door and remove the four screws located vertically along the inside lip of the door opening. These screws hold the front panel to the front shroud assembly.
afd803b.jpg

Once the four screws are removed, grasp and press in on the upper edges of the front panel posts then twist it inward to release the clips holding it to the cabinet. Tilt the top of the front panel then move it away and set it aside.
6cde6a4.jpg



The top cover is held on each side of the cabinet by two hold down brackets. Locate and remove the 5/16" hex-head screws holding each bracket.
93ee117.jpg


Swing the bracket to the outside and unhook it from the slot in the top cover lip.
67a7d37.jpg


Open the door then lift the front of the top cover and tilt it toward the rear of the machine. The door locking mechanism can now be removed and replaced.. Reinstall the top cover and the front panel by following the removal steps in reverse order.

Jan 19, 2011 | Maytag Neptune MAH5500B Front Load Washer

1 Answer

I've got a Behringer Ultrabass Bb410 1200w 4x10 Bass Cabinet in which 2 of the speakers rattle. I know the speakers have been removed and rewired. How can I get an internal wiring diagram to check...


The cabinet is listed as a 4 ohm unit.

We would exoect to see four, 4 ohm speakers in series parallel or four 16 ohm speakers in parallel.

If teh unit seems to rattle, first put an audio oscillator into it and sweep the frequency. It is common for grilles and also logos attached to them to rattle.

Open the unit and power each speaker the same way individually for a test.

I suspect you will find either the grille or mounting hardware is actually doing the rattling OR possibly the wires inside are vibrating.

If the sound is a scratchy buzz, then the speaker(s) have probably had voicecoils damaged by overheating.

In this case, buy 4 new speakers and replace all. It is not likely to find replacements for the Buggera brand they put in these cabinets. Also the word on the web about that brand of speaker is not very good.

Sep 21, 2010 | Behringer Ultrabass Bb410 1200w 4x10 Bass...

1 Answer

How to replace the ignition spark ignitor for Maytag MDG9700AWW - Thanks.


Access to the igniter (part #35001100) requires the removal of the top cover, console, and the front panel. Disconnect power to the dryer prior to servicing to avoid the risk of electric shock.

Remove the top cover by removing the two 10-mm screws attaching it to the rear of the dryer then slide the cover rearward and lift it off the dryer cabinet. Take note of the notch in the top cover engaging the screw on the cabinet during reassembly.

Remove the two screws mounting the heater PCB board to the cabinet then disconnect the black and white connectors from the board.

Remove the four screws securing the console to the cabinet then rotate the console down and remove it from the dryer.

Remove the four screws securing the top of the front panel to the cabinet and the two screws at the lower portion of the door opening. Once the screws are removed, lean forward the top of the front panel and disconnect the interior light harness. Lift the panel to disengage the three tabs securing its bottom to the base of the dryer and move the panel away.

Disconnect the igniter harness and remove the single screw attaching the igniter to the burner assembly. Slide the igniter back and remove it.

Install and secure the new igniter then make sure to reconnect the harness. Reassemble the front panel, console, and the top cover by reversing the given removal steps above.


Mar 26, 2010 | LG DLEX3001P Dryer

1 Answer

Vintage guitar speaker identification


The C12Q is a 35 watt,12 inch, Jensen replacement speaker.
The C7368 is similar to the C12Q.

These were used in Ampeg amps

the 6920006 is a patent number.

Before doing anything with the speakers check their condition. Check the voice coil resistance and manually move the cone +/- a quarter inch and listen for any rubbing.

Jan 02, 2010 | Music

2 Answers

How to remove amp from cabinet? reverb doesn't work.


SOMETIMES the handle screws must be removed as well.

I have taken a lot of these out and the key is to figure out which direction it comes out... MOST are out the back and sometimes a board across the back has to be taken off with four screws to clear a transformer.

FIGHTING getting the thing out when it catches on the Tolex covering is the USUAL problem. Takes patience and sometimes a blade to hold the Tolex back.

USUALLY the speaker baffle stays in place.

Nov 12, 2009 | Peavey Music

1 Answer

Just hooked up yesterday. Have done 3 loads. Machine shakes vigorously, moving about 2 feet. What is the problem?


Hello,

It sounds like perhaps the shipping bolts are still in the machine. Look at the back you'll see 4 large bolts that must be removed to release the main tub assembly from the cabinet.

Refer to your owners manual and it should give you an illustration of where they are located.

Also make sure all four leveling legs are secured with the locking nut against the cabinet once it has been leveled.

Hope that helps,

Good Luck :)

Oct 28, 2009 | Electrolux Kenmore 3.5 cu. ft. I.E.C....

Not finding what you are looking for?
Polk Audio Monitor 50 Main / Stereo Speaker Logo

Related Topics:

114 people viewed this question

Ask a Question

Usually answered in minutes!

Top Polk Audio Audio Players & Recorders Experts

 Grubhead
Grubhead

Level 3 Expert

5554 Answers

The Knight
The Knight

Level 3 Expert

75846 Answers

kdigby
kdigby

Level 1 Expert

37 Answers

Are you a Polk Audio Audio Player and Recorder Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...