Question about Drills

1 Answer

Load and adjust

How do i load the crews and adjust the part they go in of the makita auto-feed screwdriver

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 2,176 Answers

I would go to Makita.com and in the section under Factory and Authorized Service Centers click on that and there is a window to view and download manuals for this tool, just type in your model number. Dave

Posted on Dec 25, 2008

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Hi the battery terminals on my makita lxt circular saw are getting really hot and smells like it's burning any ideas what it could be ?


This might not be the correct answer but it could be that you are working the saw hard and drawing a lot of current from the battery.

Make sure your blade is sharp and correct for what you are doing. (Lots of teeth cross cutting, fewer teeth for ripping) and adjust your feed rate. See if that makes a difference.

Jan 28, 2017 | Makita Saws

1 Answer

Where is the mixing screw located on a Stihl 180C?


there should be a hole in the right side of the top handle that will allow your screwdriver to go in to the carb for the adjustment

Sep 22, 2013 | Makita DCS6401 20 20",64cc Chainsaw 2...

1 Answer

Why does my Auto Feed Screwdriver not screw deep enough?


What model auto-feed screwdriver do you have? All of the auto-feed drivers I have worked on have an adjustable nose peice that has to be set to the length of the screw so they will start properly and drive correctly. They also have a fine tune adjustment wheel somehwere on the tool so you can set the screw to be anywhere from just below the surface (dimpled) or flush or slightly above the surface (proud). This is all in relation to the surface the nose peice is touching. The driver is designed to release the bit when the screw has reached the depth set by the adjustment wheel so it doesn't strip out the head of the screw. I don't know of any that would let you set it so the screw would go through the plasterboard (drywall) and end up flush in the wood.

Feb 15, 2012 | Makita Drills

1 Answer

Bought it at auction. Runs fine, blades sharp, feeds fine. But doesn't seem to cut. Like the head isn't contacting the wood. What do I do?


The blades may not be positioned correctly in the cutting head. Check and adjust as necessary. The Makita Website may provide the information you need for this.

Sep 17, 2010 | Makita Tools 12" Planer - 2012NB

2 Answers

I have a Makita 100mm Disc grinder what attachments are available for this older tool...model M952


as its a grinder...there are not many attachments available....just your common grinding and cutting discs.

Aug 06, 2010 | Makita 9553NB 4" Angle Grinder

1 Answer

Auto idle does not work propertly on makita g 6101 generator


The battery charging is also a load. If the battery is not well charged or old it may need about 60 - 120 W to charge, which is not "Idle".

Jun 24, 2010 | Makita G6100R 5800 Watt Generator

2 Answers

Stihl ms310 chainsaw will only run on choke


You actually need the adjustment tool,looks lie a small screwdriver with a smal socket at the end of it.

Jun 02, 2009 | Makita DCS6401 20 20",64cc Chainsaw 2...

1 Answer

Drill Presses problem


If adjustments are necessary, follow the this procedure: Spindle side-play can be minimized by adjusting the locknut located on the left side of the motor unit 1-1/2 inches behind the spindle and towards the bottom of the motor unit. While moving the feed handle up and down, tighten the lock nut until the play is minimized, but not so tight so as to restrict free movement of the spindle. The spindle should return by itself to the full up position. The drive belt tension may be adjusted by removing the top cover and then loosening the two nuts on either side of the motor pulley. Adjust the motor position and tighten the nuts so that moderate finger pressure against the belt causes it to deflect 3/16" to 1/4" (see Figure 6). Excessive belt tension may result in damage to the bearings. Note: Belt tension can also affect the generation of "noise" in the drill press. Although it does not affect drilling accuracy, it may be desirable to adjust the tension for minimum noise. The spindle has been generously oiled at the factory. You may have to periodically wipe off oil that makes its way down the spindle.

Aug 27, 2008 | Makita 6825 Factory Reconditioned Drywall...

4 Answers

Feed dog is stuck


I have the same problem...this is a work around, not a fix. You need a small flat-head screwdriver. 1. Remove the clear bobbin cover. 2. Make sure the feed dog switch is in the DOWN position. 3. Slide the screwdriver under the feeddogs from inside the bobbin area & lift the feed dogs. 4. While holding the feed dogs in the up position, return the feed dog knob to the up position. You have to do this every time you put the feed dogs down...bummer, but I can find no broken part or adjustment that corrects this. If it's inside the machine body, I don't mess with it... I did take off the bottom plate in the feed dog area..one screw holds it.... there is nothing there to indicate a problem.

May 07, 2007 | Singer 2662

3 Answers

Janome 9000 Feed Dog and On/Off button problems


Try the emboadery slide in the back of the machine, This happened to me you just need to slide it over to the other side. It dose tell you this in your book.

Nov 17, 2006 | Janome Memory Craft 9000 Computerized...

Not finding what you are looking for?
Drills Logo

Related Topics:

103 people viewed this question

Ask a Question

Usually answered in minutes!

Top Drills Experts

yadayada
yadayada

Level 3 Expert

70346 Answers

EugenesDIYDen
EugenesDIYDen

Level 3 Expert

479 Answers

Brad Brown

Level 3 Expert

15100 Answers

Are you a Drill Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...