Question about Frigidaire GLTF2940ES Front Load Washer

3 Answers

Frigidaire GLTF2940ES stopped with Error Code E23. Does not drain, makes a humming noise on start. Does not spin or drain.

Posted by on

  • Neil Golan
    Neil Golan Dec 25, 2008

    Hello
    Welcome to Fixya
    My name is Huum,


    E23 means
    Drain pump relay on the control board fails.
    Change control board or fix wire!

    Thank You For trusting us with your question
    Please remember to leave a solved rating before you leave!



  • railer74 Jan 15, 2009

    Is this problem the upper main control board or the lower motor control board? If it's the lower how in the heck to you get it out?

×

3 Answers

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that has over 10 points.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 3 Answers

Onthejob5130 is right, the machine use E23 too tell you that the pump is obstructed.
before buying anythings, you have too check the manual too see if you didn't put it in factory test mode by accident. the manual is suppose to be under the top,(two screws on the back)
After that, second thing you have too do, remove the back (six screws) the drain pump is located under the the baril. there is a black rubber tube attached to it. In this tube, there is a basket that keed hard thing away from the pump. In my case, some hair pin pass the basket and block the pump rotor. The computer of the machine told me it was Error E23 but after cleaning, everything work like new!!

So try cleaning it yourself, it is easy even with basic skill. You will need a star screwdriver, a scare-screw driver, pliers.

Remember, better have the machine empty before doing anything, because you'll be working on the DRAIN LINE.

Hope that help someone.
Vincent D.

Posted on Jul 25, 2010

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 750 Answers

Hello
Welcome to Fixya
My name is Huum,


E23 means
Drain pump relay on the control board fails.
Take off the panel and clean the pump filter
Change control board or fix wire!

Thank You For trusting us with your question
Please remember to leave a solved rating before you leave!

Posted on Jan 04, 2009

  • Neil Golan
    Neil Golan Feb 03, 2009

    this problem the upper main control board

×

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 640 Answers

Take toe panel off unit than empty your pump filter...

Posted on Jan 03, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have an Affinity washing machine that shows an E23 error code.


Hello Robert Reische, thank you for your inquiry!

I understand that your Frigidaire washer is showing an "E23" error code. Based off the information I show "E23" stands for drain pump relay on board failed or wire off the pump. Which means you could have an issue within the main control board or wiring to pump. Since it could be any one of these underlying issues I would recommend having a technician come out to properly diagnose and repair your appliance. Hopefully this helps. -Matt

Sep 11, 2014 | Frigidaire ATF6000ES Front Load Washer

1 Answer

What does error code E23 on a frigidaire affinty front load washing machine mean


Good Morning Friend,

I understand you are receiving an E23 code on your Frigidaire Affinity washer, model# GLTF2940ES. The E23 code states that the drain pump relay on the control board has failed. This could also be a possible false code. I suggest resetting your appliance, by either unplugging it or shutting the power off at the circuit breaker, for 3-5 minutes. Restore power and start any cycle. I ask that you please follow up with a comment on the post, at your convenience, to advise if further troubleshooting is needed or if your appliances status has changed successfully. Hope this is helpful.

-Best Regards-
WP

Jun 18, 2014 | Frigidaire GLTF2940ES Front Load Washer

1 Answer

My frigidaire afinity washer was not draining. I opened up the washer and there was a small sock in the drain. i removed it and started the washer again, but the washer still will not drain. it gives me a...


Hello Juan, thank you for your post!

If you are getting an error code E23, it usually means one of three things: your drain pump relay has failed, a wire may be disconnected from the pump, or your main control board possibly needs replacing. One of the best ways to determine if this is a false error code is to reset the power to your Frigidaire washer by either unplugging it or flipping off the breaker for about ten minutes. If the error code persists, it would be advisable to contact an experienced appliance repair tech to assist further.

Best regards - Z.

Apr 04, 2014 | Frigidaire GLTF2940ES Front Load Washer

1 Answer

Starts then shuts off never fills w/h2o, says e23


Good Morning Mike, I am happy to assist you!

If you are getting an error code E23, it usually means one of three things: your drain pump relay has failed, a wire may be disconnected from the pump, or your main control board needs replacing. One of the best ways to determine if this is a false error code is to reset the power to your washer by either unplugging it or flipping off the breaker for about 30 seconds. If the error code persists, it would be advisable to contact an experienced appliance repair tech to assist further.

Feb 20, 2014 | Frigidaire GLTF2940ES Front Load Washer

1 Answer

Filter replacement for frigidaire gltf2940es


Hello - The error code "E20" typically means the water is not draining properly or not pumping out fast enough. Does the washer making a humming noise? If so, either the drain hose may be kinked or the drain in the house is clogged. Once you have confirmed and cleaned the hose and issue continues contact a professional to move forward accurately. The unit may possibly have a faulty pump or control board.

Nov 05, 2012 | Frigidaire GLTF2940ES Front Load Washer

1 Answer

Error code e20


Hello leah_mcmunn - the error code E-20 indicates that the water doesn't drain. This could be caused by either the drain hose is kinked or your household drain is clogged. If the drain pump is making a humming noise, check the restriction in the drain line. If not, then you might need to contact a professional to possibly replace the pump.

Sep 20, 2012 | Frigidaire GLTF2940ES Front Load Washer

1 Answer

We have an Affinity ATF6000F washing machine that makes s horrible noise during the spin cycle and shuts off with water still in the basin. When we hit Start and Cancel at the same time we get code E23.


Hi,


The error E23 denotes the drain **** relay on control board is failed.


Check whether there is some lose connections in the wires if nothing lose connection is there then you need to replace the control board.


Thank You

Sep 04, 2010 | Frigidaire Affinity ATF6000F Front Load...

1 Answer

Water in the drum humming noise Code error e23 Kenmore washer


It sounds like your drain pump is blocked.

There should be a small door at the front of the machine. Open it and unscrew the coin trap (plunger) and see if there's anything stuck in there.

If not, then you will have to look under the machine and remove the drain pump manually to clear it.

Hope this helps!?

Jun 19, 2009 | Frigidaire GLTF2940ES Front Load Washer

1 Answer

Code E20


my cloths will wash but will not spin out the drum stop turning when it comes to the spin cycle makes a humming noise

Mar 30, 2009 | Frigidaire GLTF2940ES Front Load Washer

1 Answer

Error Code E23


Hello welcome to Fixya

E23 means
The drain pump relay on the control board has failed.
Fix: Replace control board or wire!

you can see schematics and diagrams at the site below, and order parts from them if you want.
Or call service!

http://www.pcappliancerepair.com/model-display.php

Thank You For trusting us with your question
Please remember to leave a solved rating before you leave!

Dec 24, 2008 | Frigidaire GLTF2940ES Front Load Washer

Not finding what you are looking for?
Frigidaire GLTF2940ES Front Load Washer Logo

549 people viewed this question

Ask a Question

Usually answered in minutes!

Top Frigidaire Washing Machines Experts

Electrolux
Electrolux

Level 3 Expert

4342 Answers

Richard Roth
Richard Roth

Level 3 Expert

9472 Answers

Dan Webster
Dan Webster

Level 3 Expert

8205 Answers

Are you a Frigidaire Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...