Question about D-Link DFL-800 (DFL800) Firewall

2 Answers

My firewall DLINK 800 drops my connection ADSL perioducly

Posted by on

2 Answers

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 2 Answers
Re: My firewall DLINK 800 drops my connection ADSL...

I have the same problem!! Have you fixed it? How?


Posted on Apr 15, 2013

  • Level 2:

    An expert who has achieved level 2 by getting 100 points


    An expert that gotĀ 5 achievements.


    An expert whose answer gotĀ voted for 20 times.


    An expert who has written 20 answers of more than 400 characters.

  • Expert
  • 84 Answers
Re: My firewall DLINK 800 drops my connection ADSL...

It sounds like you don't have it set up with the Keep Alive setting

Posted on Jun 17, 2007

Add Your Answer

0 characters

Uploading: 0%


Complete. Click "Add" to insert your video. Add


3 Points

Related Questions:

1 Answer

Sonicwall keeps dropping braodband connection

Bad ADSL modem at your ISP's end?
Deteriorated twisted-pair wires from the telephone-pole to the demarcation box on the outside of your home?
Dying ADSL modem inside your home?

First, try a different ADSL modem.
Then, call your Internet Service Provider, and get them to trouble-shoot.
Finally, switch to a cable-modem provider.

Jan 29, 2014 | SonicWALL Tz 105 Totalsecure

1 Answer

How to connect basic

You have both equipments with the same ip address. Connect the PC to the firewall, login and change the IP first.

Jul 22, 2013 | D-Link NetDefend DFL-700 Firewall

1 Answer

I am trying to connect my ipad 3 to my dlink 600L. It will ask for password but will not connect when password is putin

Here's a video Harshit kumar suggested as a solution to your problem from YouTube:

Fast D-Link Wireless Router Security Setup

Apr 19, 2013 | D-Link Dir-600l Wireless N 150m Home Cloud...

1 Answer

Dfl-800 loses connection

i have the same problem!!! have you fixed it? How?


Nov 06, 2012 | D-Link DFL-800 (DFL800) Firewall

1 Answer

Dear sir. I lost my dlink dsd-150's installation cd, do you konw where i can download the software?

Dlink DSD150 User Manual
CD is not available separately or from Dlink Support and you dont really need the CD either. From the above link you can download the user manual.
After the SecureSpot hardware is installed, the security services subscription must be activated. From any PC on the network, attempt to browse the Internet. The browser should be redirected to the Thank You page. (Be sure to disable or uninstall any Internet Security or Personal Firewall Software to prevent registration/client installation problems)
Also from the above link you can also check the Emulator to facilitate the installation & configuration process.

Hope it helps! Good Luck!

May 10, 2011 | D-Link SECURESPOT DSD-150 (790069291944)...

1 Answer

Unable to reset Dlink DFL 700 network firewall

To perform a factory reset using the reset button do the following:

Step 1: Make sure that the DFL-200/DFL-700 is on.

Step 2: Press and hold the button located on the back of the DFL-200/DFL-700 below the word Reset using a paper clip for 10 seconds.

Step 3: Release the button.

Oct 23, 2009 | D-Link NetDefend DFL-700 Firewall

2 Answers

How to configure

Oct 07, 2009 | D-Link DFL-800 Firewall

1 Answer

How do I set my Netgear FVL328 to be a switch for my network? I have a Dlink DIR-655 connected to my cable modem. But I don't have enough ports for all of my devices. So I connected the Netgear FVL328...

If I understand, the D-link is a switch but you don't have enough ports so you want to use the Netgear to get additional ports.
The way to do it is to use one of the Netgear Lan ports to connect to one of the D-link ports, then use the remaining Netgear ports for your stuff, leaving the WAN port disconnected.
Personally I would use the Netgear as a firewall and connect the D-link to get the additional ports.
Also, Apparently the Netgear and the cable modem or D-link are both running DHCP servers to assign IP addresses to connected devices that need one assigned. You should turn the DHCP server off in whatever unit is being used in a slave fashion. This is done in the netgear by opening a browser and typing in the IP address for the netgear, which is probably, and logging in using username 'admin' and password 'password' unless you changed them.

Mar 15, 2009 | NetGear FVL328 and FA311...

Not finding what you are looking for?
D-Link DFL-800 (DFL800) Firewall Logo

Related Topics:

238 people viewed this question

Ask a Question

Usually answered in minutes!

Top D-Link Network Security & Firewall Devices Experts

Rick Johnson
Rick Johnson

Level 2 Expert

84 Answers

john smith

Level 2 Expert

366 Answers

Alex Krenvalk

Level 2 Expert

401 Answers

Are you a D-Link Network Security and Firewall Device Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides