Question about Hotpoint Ultima WF865 Front Load Washer

1 Answer

Hotpoint wd865 dryer stopped working

Bought 16mths ago dryer was not used that much, suddenly dryer no longer produces any heat but still goes through the cycle no error massages appear. Please help

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Novelist:

    An expert who has written 50 answers of more than 400 characters.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

  • Expert
  • 161 Answers

I always start at the plug to make sure it has 220, a dryer will run but no heat with 110. This was a common problem when everyone used fuses instead of breakers, just an old habit.

Then I check the heating element and thermostats, this must be done with an OHM meter. More than likely it will one of these.

Posted on Dec 23, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Hotpoint wd420 shows error code f13 after replacing heater element for dryer.


Change electronic board it is what will cause this problem if you checked all ducts an fan and still heats board is bad

Oct 28, 2014 | Hotpoint Ariston Aquarius WD420 Front Load...

1 Answer

My dryer has stopped heating completely. Worked fine for six years and stopped heating four days ago.


Hi,

If you are having problems with your gas dryer not heating the most common problem is that the ignitor goes bad. Even though it glows sometimes it is still not working properly.


if you dryer is gas check out this gas no heat tip....


If you have an electric dryer, you can have many different things that can go wrong causing the dryer not to heat.


check out this electric no heat tip...


heatman101


\\]\\

Nov 06, 2010 | Frigidaire FLEB8200DS Top Load Stacked...

2 Answers

MY HOTPOINT CONDENSER TUMBLE DRYER NO LONGER HEATS UP. IT NOW OMLY BLOWS COLD AIR


This sounds like the thermostats or heater

ForAll Your Appliance Video Help Visit Apart4u video tutorials

see other tumbledryervideos here



You-Tube video "sfGInKA3yp8" placeholder (do not delete)



Common faults -
1 The heating elements can fail(meaning open circuit)
2 There are cut-outs (T.O.C's) thatmight need resetting
3 The thermostats (stats) can tripout or burn out (meaning opencircuit)
4 Moderntumble dryers also have sensors and pcb's (Printed circuitboards) thesehaveprograms that can fail and circuitry although most should produce an errorcodeshowing you were the fault is.
5 Faultyconnections and burned wires may also bethe fault.

Nov 17, 2009 | Hotpoint Aquarius WMA42 Front Load Washer

1 Answer

Wd865 error f01


f01 is a motor problem. may need a new one but an engineer visit would confirm this.

Feb 01, 2009 | Hotpoint Aquarius WD640 Front Load...

2 Answers

WD865 Hotpoint - F-05 error


F05 means that the pressure switch is jammed on full.
You need to check the pump is pumping out o/k, and if there is a filter, check and clean.

Jan 11, 2009 | Hotpoint Ultima WF860 Front Load Washer

1 Answer

Washer dryer wont stop running


unplug the machine for 3 mins and plaug back in if it still happens you might have a problem with the heating element or somthing.hope this helps.

Jan 02, 2009 | Hotpoint Aquarius WD63 Front Load...

1 Answer

Hotpoint Washer Dryer WD865 - Dryer Problems


thermister blown or thermal fuse which is a black plug in the top of the dryer box or yellow sleeved wire, if it was noisy maybe the fan has come loose from it's motor. you will need to remove the dryer box on top of the drum to see if the fan is binding. you can push it back to where its not binding and tighten the nut-ANTICLOCKWISE, LEFT HAND THREAD.
usually the machine runs through a check before starting a cycle and will see an f13 and not start even a wash., so you will need to replace the blown parts.

Oct 25, 2008 | Hotpoint Ultima WF865 Front Load Washer

1 Answer

My Hotpoint washer dryer WD865 moves around the room making loud noises when on a fast spin? The internal drum seems more loose than normal?


I had the same problem. You can open the top lid (2 screws at the back and then lift) The weight which is on top is secured by three bolts, all three of them were loose so weight was going from one side to another which made a terrible noise. Tightened the bolts and noise was gone!
Dryer still not working though.....

Aug 06, 2008 | Washing Machines

1 Answer

Hotpoint wd440 flashing dryer heat button and onoff button !


I had to have a tech come out for the same problem two weeks ago. They had to clean the lint collector which you cannot get to on your own. He said now that this has been done everytime I use the machine, take the clothes out and then run a rinse spin cycle.

Aug 04, 2008 | Hotpoint Aquarius WD63 Front Load...

Not finding what you are looking for?
Hotpoint Ultima WF865 Front Load Washer Logo

Related Topics:

365 people viewed this question

Ask a Question

Usually answered in minutes!

Top Hotpoint Washing Machines Experts

hungoverrr

Level 1 Expert

5 Answers

puggy666

Level 1 Expert

47 Answers

gbob59

Level 3 Expert

2963 Answers

Are you a Hotpoint Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...