Question about EnGenius EOC-3220 (EOC3220)

1 Answer

Slow and lousy connection

I'll start by stating that I know little about this form of technology - so plain English answers are much appreciated.
I have an iMac and recently purchased an EnGenius EOC-3220+ that is to connect with an Access Point located nearby.
I don't have line-of-sight with the Internet Tower, but my neighbour does so he accepts the signal, runs it through a router and then sends it to the access point where it connects with my 3220+.  It then runs down a tree, into my house and to my iMac.
In order to get ANY connection to the internet, I needed to slow my speed to 10 mps from 100.  However, even at that rate, I get slow and intermittent connection to the net - I often get a "timed out" error on sites, etc.
Any help is greatly, greatly appreciated

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

DON'T BE AFFRAID I WILL SOLVED YOUR PROBLEMS NOW . READ THIS AND SOLVE YOUR PROBLEMS . IF YOU DO NOT KNOW HOW TO USE THIS FORM OF TECHNOLOGIY , GO AND SEE A TECHNITIAN WHO KNOW HOW TO USE THIS TECHNOLOGY AND IF YOU ARE NOT SATISFY, COME AND WRITE TO ME IN THIS ADDRESS : angoundjou@yahoo.fr

Posted on Dec 24, 2008

6 Suggested Answers

davecon
  • 85 Answers

SOURCE: Engenius EOC-3220+

if you have a the router's manual,there is a guide on how to do that.

but in case you dont have the manual go to the device website and get some guide.default ip varied from different manufacturer

Posted on Apr 23, 2008

manoline
  • 52 Answers

SOURCE: how do i reset my Engenius EOC-3220

This might be helpful

http://www.fixya.com/support/t629167-getting_setup_pages

Posted on Nov 07, 2008

rahul26485
  • 611 Answers

SOURCE: how do i reset my engenius senao eoc 3220 outdoor

back side one reset button is there pull out the power cable then pull in that same time you have to press the reset button for three to five sec then all lied's blink all to gather then your default ip address is came then you again configure at default ip

Posted on Apr 17, 2009

Macs R We
  • 481 Answers

SOURCE: I have a EnGenius EOC-3220

I'm sorry, there is no problem statement here. If you have a specific problem, please provide it.

Posted on Oct 27, 2010

Macs R We
  • 481 Answers

SOURCE: i have EnGenius EOC-3220 (EOC3220)

Depending on the serial cable you have, you may need a modem (crossover) adapter between the cable and the EOC-3220. A good diagnostic is the following: with the EOC-3220 unplugged from power, connect your serial cable and make all the proper baud rate etc. settings in your serial communications program. When it is running, plug the EOC-3220 into power. If you don't see any garbage characters appear on your screen when you plug the power in, your comm program is probably not set up properly. If you see garbage characters but they are not immediately followed by good information from the EOC-3220, then you either need a null modem adapter inline, or you have a dead EOC-3220. If you've never communicated successfully with an EOC-3220 before over the serial channel, the only way to know if you have a dead one is to try again with a known-good one.

Posted on Oct 27, 2010

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Roku connection


Your question is so very non discernible that I may not be answering your question. Please use proper english next time.

In any case, I did find this howto on setting up a Roku player to your computer. I hope this was your question..??

How do set up my Roku player

In closing, I was not trying to come across as condescending. I truly love helping people solve their tech issues. I find it very stimulating and satisfying.

It just makes that process exceedingly difficult when you don't even form a proper english sentence.

After all, who knows if I even answered your question?

Apr 01, 2014 | Computers & Internet

1 Answer

I want to start my plumbing company in toronto, what I will do?


I think you need to talk to a lawyer or a CPA to find out what to do. You'll need to decide what form your business will take - corporation (and what class), partnership, or sole proprietorship. You'll need to know where to file what forms - incorporation, tax forms, registrations, etc. You'll need to know what areas you will set up policies for - ie, treating employees, buying health insurance for them and yourselves or not; you'll need to know what kinds of bank accounts you'll need; you'll need to decide on accounting procedures. You will get more information in hear about Toronto plumbing company.

Sep 01, 2012 | Sterling Plumbing Home

1 Answer

Have a toshiba a10 and a vizio hdtv, what cable do I need to connect the two


Hi.

You don't say what you intend to do once the 2 devices are connected. I am going to assume that you just want to use the vizio hdtv as a large external monitor.

The laptop's vga (15-pin blue or black D-shaped) port can connect direct to the hdtv via it's blue vga (15-pin blue D-shaped) port.

However, your toshiba a10 laptop is relatively old, discoontinued technology with (in original specification) low RAM (256mb ddr), a single, slow processor (2.2ghz celeron) and slow (4300rpm), small hard drive (30gb), with limited, low level vga graphics capability, running xp home edition operating system. VGA is a slow analogue video technology.

To get the full benefit of the hdtv, which is almost state-of-the-art, you need a laptop with a fast dual or quad core processor, 3-4gb ddr3 RAM, 320-500gb 5400-7200rpm or solid state HDD, running the latest windows 7 operating system. Such a laptop would have hdmi ports and powerful, fast, state-of-the-art graphics capability.

A new laptop would unlock the full spectrum of , high definition video, high speed audio-visual streaming, fast video-editing, multimedia functionality between the two devices.

For your current laptop you need a male-to-male 15-pin, D-Sub VGA cable.

For the recommended or a similar, modern laptop you would need an HDMI cable.

Hope this helps.

Aug 02, 2011 | Computers & Internet

2 Answers

Cant find motherboard specs. ________________________________________ Hello. I cannot find the specs for my motherboard. Its the comp in my sig and the model number is E946GZT-AM.V1.0 its whatever came in...


As requested motherboard specifications for the Acer Power FH desktop computer,

http://support.acer.com/acerpanam/desktop/0000/Acer/PowerFH/PowerFHsp2.shtml

1) Processor Support:
Tells you what Intel processors are supported.

If you do not know what you are looking at, let me know, I'll explain it.

Doesn't state it, but I can tell you that it has an LGA 775 processor socket.
Has to in order to support the Intel processors stated.

This is what an LGA 775 processor socket looks like,

http://en.wikipedia.org/wiki/Socket_T

2) Ram Memory Support:
Has two ram memory slots.
Each slot has a Maximum Amount of 1GB.
Total Amount for the motherboard is 2GB.

Supports (Uses) DDR2 Sdram that operates at a frequency rate of either 533MegaHertz, or 667MHz.
Which is PC2-4300 and PC2-5300 respectively.

3) Motherboard Chipset:
Uses an Intel 946GZ Northbridge chipset, and a
Intel ICH7 Southbridge chipset.

The link below states what the Intel 946GZ/Intel ICH7 chipset will support,

http://en.wikipedia.org/wiki/List_of_Intel_chipsets#Core_2_Chipsets

4) Graphics Support:

Has the Intel GMA 3000 GPU for Onboard (Integrated) graphics.
(When you use the VGA port on the back of the computer.

http://en.wikipedia.org/wiki/Intel_GMA

( GPU stands for Graphics Processing Unit. Type GPU in Wikipedia's search box for more information )

Also has a PCI Express x16 slot for a graphics card.

This graphics slot uses the PCI Express 1.1 technology.

Looking back at the link for the Intel 946GZ/Intel ICH7 chipset you can see it was brought out in the 7th month of 2006.

(Release Date: 2006.07)

The PCI Express 2.0 technology was brought out
January 15, 2007.

If you're wondering, whether a graphics card based on the PCI Express 2.0 technology will work on it, the answer is yes with no sweat.

The reason why is that PCI Express 2.0 technology is Backward Compatible with PCI Express 1.1 technology.

You won't get the full capability of the PCI Express 2.0 graphics card.

Will you notice? NO.

Games and 3D programs haven't begun to scratch the bandwidth of PCI Express 1.1 yet, much less the PCI Express 2.0 technology.

(Look up PCI Express on Wikipedia.
Also check out the external links at the bottom of the page)

I'm guessing the form factor of the motherboard is ATX, but I am just guessing at this point.

I base my deduction on the fact that a PCI Express x16 slot, and a PCI Express x1 slot is used, plus there are two PCI slots. (All are Expansion Slots)

You have to have enough room for all this hardware, and I don't see a Micro-ATX form factor motherboard as having the room.

But you can easily check for yourself.

Micro-ATX is 9.6 inches by 9.6 inches.
(244mm by 244mm)
9.6 inches is approximately 9 and 9/16ths inches.

ATX is 12 inches by 9.6 inches.
(305mm by 244mm)

That's the main highlights of the motherboard. Is there anything else you wish to know about it?

If the computer is operational, and internet capable, you could go to CPUID.com, and download the tiny, little program CPU-Z.

It's free.
Gives you a real in-depth look at your computer hardware specifications, and what you have presently installed right now.

Should you need help in downloading it, or using it, let me know in a Comment.

Mar 02, 2010 | Acer Power FH PC Desktop

2 Answers

Cant get the question mark, tried many combinations


I just got this answer directly from Acer. It worked for me. Hopefully it will work for you too;

Please do the following steps to resolve this issue.
1. Click on Start > RUN
2. type intl.cpl in the Run box, and then press ENTER.
3. On the Languages tab
4. Click the Details button.
5. In the Settings tab, under the Installed services section, click the Add button.
6. In the Input language list, click the language that you want; English (United States) [or English (Canada)].
7. In the Keyboard layout/IME list, click United States-International, and then click OK.
8. In the Settings tab, under the Default input language section, change the language to English (United States) - United States-International [or English (Canada) - United States-International].
9. Click the Apply button and then the OK button.
10. In the Regional and Language Options dialog box, click the OK button to close the dialog box.
11.Notice that the Language bar appears on the taskbar. When you position the mouse pointer over it, a ToolTip appears that describes the active keyboard layout; English (United States) appears [or English (Canada)].

Jan 11, 2009 | Acer NSK8458AN Keyboard

2 Answers

Stuck in French


hold down the Code key(blue/green) and press Keyboard, You might have to do it once or twice, All brothers have international keyboards. good Luck! Don

Apr 30, 2007 | Brother IntelliFAX 775 Plain Paper Thermal...

Not finding what you are looking for?
EnGenius EOC-3220 (EOC3220) Logo

219 people viewed this question

Ask a Question

Usually answered in minutes!

Top EnGenius Computers & Internet Experts

john smith

Level 2 Expert

381 Answers

WTF Chuck.....
WTF Chuck.....

Level 3 Expert

386 Answers

Jacqueline

Level 2 Expert

76 Answers

Are you an EnGenius Computer and Internet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...