Question about Price Pfister Ashfield Single Control Lavatory Faucet ...

1 Answer

Shower mixer taps

The shower mixer we have had fitted will not allow Hot water through only tepid water, it is fed from a combi boler that serves the c/h all other hot water taps discharge hot water.

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 15,935 Answers

Look for a scald safety screw adjustment. Remove the handle, and it is underneath. this is for safety of young children, and is factory set.

Posted on Dec 23, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Our bath taps which are a mixer with shower attachment stay really hot if you put the hot on first or really cold if you put the cold on first any idea how to adjust so we can have warm water when turning...


you make no sense. From the picture the water "mixer" is the center lever or is it a diverter valve for the shower and water nozzle below???
The knobs are for hot and cold water??

Jun 08, 2014 | Faucets

1 Answer

Grohe mixer will only start the pump on cold. Is the unit faulty.


Ive written a solution twice but for some reason it wont let me post it.I will try to abbreviate it.

You dont say how much flow it has when the pump isnt running but I suspect there isnt enough to turn on the sensor unless all the flow is one side. ie all cold.

May 06, 2012 | Grohe Faucets

2 Answers

How do I remove cartridge part # 9273000 from my Hansgrohe kitchen faucet?


Hello,

Please contact us at the below number or email me directly and I will get you a copy of the instructions that you need.

Regards
Chris

Christopher Scott
Technical Support Specialist
Hansgrohe Inc.
1492 Bluegrass Lakes Parkway
Alpharetta,Ga 30004
Tel:1-800-334-0455
Fax:678-762-7042
Email:Christopher.Scott@hansgrohe.com

Feb 19, 2011 | Hansgrohe 06649860 Solaris Single Hole...

1 Answer

My taps are new. When the handle is turned full hot , the water is only tepid. I think the anti scald feature is letting too much cold water pass. Please advise


there is a splined adjustment just under the handle of the 3175.

you need to remove the handle, usually held on with an allen screw
once you remove the handle, there will be a black "stop" held on with a screw, remove that, but remember its position.

once that is off you can adjust the temperature. there will be 2 white pieces, one has splines, you can move this counter clockwise one or two notches at a time untill you reach your desired termp.
be careful not to go too much, even though these are an anti scald valve, you are letting more hot water through it.

Aug 12, 2010 | Moen 3175 Legend One Handle Shower Faucet...

1 Answer

We have two 16 year old shower faucets (house was built in 1993 by Del Webb). Can't tell what model they are. We are guessing they are Moen Legend 3175 (one handle). Problem seems to be pressure balancing...


This is a common problem with this type of shower mixer valve. They are not very good at regulating with pressure change. Your options are somewhat limited to not flushing the toilet or using any other taps when in use, repalce the mixer valve for a modern ceramic unit or installing a 2 vane hot & cold shower pump.

Nov 09, 2009 | Moen 3175 Legend One Handle Shower Faucet...

1 Answer

Low water flow


buught sink taps same problem do they have flexy conectors with them. my problem was as they are american hot @ cold water suply are maines fed so hole in bottom of taps [or in flexy pipes are too small

May 17, 2009 | Danze D302521 Antioch Roman Tub Faucet...

1 Answer

Shower not hot


There is a handle limit stop under the handle. Remove the handle with an allen wrench and you should see a plastic piece with a tab on it fit into the assembly. Remove it and rotate it slightly to allow more travel in the handle and reinsert. You will have to test it to see if it allows enough hot water to mix in. If it is still not warm enough repeat as needed. Once you have the water at a comfortable temperature reinstall the handle and enjoy.

Dec 31, 2008 | Faucets

1 Answer

No cold water only, just tepid to hot on thermobalance I


hi i think the problem is the temp has not been adjusted to your requirements as it will come factory set at 43 deg c so you will probably need to get it adjusted by the guys who fitted it as it wiil need to be set by a professional.

Nov 14, 2008 | Faucets

Not finding what you are looking for?
Price Pfister Ashfield Single Control Lavatory Faucet ... Logo

483 people viewed this question

Ask a Question

Usually answered in minutes!

Top Price Pfister Faucets Experts

Roscoe007

Level 2 Expert

101 Answers

Rich Florenzen

Level 2 Expert

333 Answers

yadayada
yadayada

Level 3 Expert

61203 Answers

Are you a Price Pfister Faucet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...