Question about Hoover Elite Rewind Bagless Upright VacuumVacuum

1 Answer

Hoover Elite Rewind belt part number , is this the correct one?

I had the belt broke...I opened to replace..the part number was 38528 with a flat type belt ( like a car serpentine belt)and not rubbery and round cross section. I looked at the turning brush and the groove was round. Now, I wonder does this vacum cleaner have the right belt on it? becasue the groove is round and the belt is flat.
thanks.

Posted by on

  • wsuman44 Dec 23, 2008

    Thank you for your time and help.Merry Xmas .

×

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Governor:

    An expert whose answer got voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 107 Answers

Yes, that is the correct belt. The full part number should be 38528040. This is the correct belt and should fit your U5509/U5507.

Posted on Dec 23, 2008

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

I have a Hoover Wind Tunnel vacuume that the brush does not work. Replaced it with the Hoover Belt 38528-034 and it does not move what's up with that?


The brush roller may be clogged with debris. If so, the belt will only slip until it burns through from friction.

Nov 19, 2017 | Hoover Vacuums

1 Answer

What is the belt part no. for a hoover elite rewind?? model no. UH71009RM


If you look up the Hoover page for the UH71009 (the non-remanufactured Elite Rewind), there are 3 different belt model numbers listed. One part number is simply for a 2 pack of the belts. See http://hoover.com/products/details/uh71009/elite-rewind-bagless-upright/ . Click on the Parts & Accessories tab.

I believe the belt part number is 38528058 , http://hoover.com/parts/details/38528058/sra-r-b-562932001-belt/ .

I hope this helps.

Cindy Wells

Oct 04, 2015 | Hoover Vacuums

1 Answer

How do I make the noise stop?


Seems like the bearing on the side of the roller has gone bad. If there is a dirt gone deep inside, it is hard to clean it. It can also go bad if the roller hits the uneven surface like the transition strip between carpet and tile. It can unbalance the roller causing it to go off its axis and get misaligned.
This is the roller for the Hoover Elite Rewind
http://www.ezvacuum.com/hoover-93002124-brushroll-for-u5509-u5511-u5512-elite-rewind-p-3607.html

May 20, 2013 | Hoover Elite Rewind Bagless Upright...

1 Answer

Hoover belt 38528 027


The belt should be available from Hoover or a vacuum cleaner repair shop

May 10, 2013 | Hoover U5227-930 Elite Upright Vacuum

1 Answer

How do I change the belt on my Hoover Elite Dual Purpose Vacuum cleaner? The belt part # is 38528-027. Where is the motor pulley?


The hoover belt number you listed (38528027) has been changed by Hoover to 38528040. Below I have listed a link to the manual that has instructions and a link to the belt you need. Hope this helps!

Hoover Elite Manual

Hoover Elite Replacement Belts

Nov 02, 2009 | Hoover Elite U5061-900 Bagged Upright...

1 Answer

My hoover elite rewind is making a louder noise and I can smell something burning when I use it. I have replaced the belt but this did not help.


the smell is either the motor or the belt, if motor hope it is under warranty, if belt make sure brush roll spins freely and replace belt, if brush roll not spin freely replace it first

Aug 27, 2009 | Hoover U5507900 Elite Rewind Bagless...

1 Answer

Replacement belt # for hoover wind tunnel model u5750-900. original belt # 38528-035, please


your belt number is correct ending in 035. I have had luck with belt number ending in 033 also.

Jan 28, 2009 | Hoover U5750-900 WindTunnel Bagless...

2 Answers

Replace the belt


Once the bottom plate has been removed, the motor shaft is silver, but hard to see. hook the new belt on it first. then start rolling on the top of the large black pulley to install.

I’m happy to assist further over the phone at https://www.6ya.com/expert/robert_b96ba3f038cf317c

Jan 26, 2009 | Hoover Ultra U6430-900 WindTunnel Bagged...

Not finding what you are looking for?
Hoover Elite Rewind Bagless Upright VacuumVacuum Logo

Related Topics:

1,433 people viewed this question

Ask a Question

Usually answered in minutes!

Top Hoover Vacuums Experts

Les Dickinson
Les Dickinson

Level 3 Expert

18426 Answers

Jim Parker
Jim Parker

Level 3 Expert

1041 Answers

Gerry Harvey
Gerry Harvey

Level 3 Expert

1474 Answers

Are you a Hoover Vacuum Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...