Question about Whirlpool Duet GHW9150P Front Load Washer

1 Answer

I have lost my manuel and am trying to do a handwashables load. it says not to spin. How then do I get the water out of the cloths and as a side question why would the washer have a choice of no spin. Thank you.

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Whirlpool Master
  • 2,651 Answers

Reason for a "HAND WASHABLE" is the delicate nature of the clothing to be Hande washed. thus the LOW spin. no spin option for soaking clothing, heres the manual

http://shared.whirlpoolcorp.com/assets/pdfs/literature/Use%20and%20Care%20Guide%20-%208182271.pdf

Posted on Dec 23, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Will not spin the water out of the clothes


call a repairman sounds like a controller problem or transmission not getting final rinse signal

Mar 15, 2015 | GE Profile PTWN6050MWT 27" Top-Load Washer...

1 Answer

I have a 2 month old Speed Queen top load (542) after the spin cycle, the clothes are still very wet


i assume the majority of the water is being pumped from the machine? if the clothes are very wet check your "fabric Select" setting and ensure you are not wahing on delecate handwash or wool wash (knits) setting, in this setting there will be a very slow or no, spin so the clothes will not stretch and have to be laid out to dry this is normal. if you are on a Permpress or regular setting the spin should be faster, also check your cycle selection is for Regular or permpress and spin is not missed .

I hope this was useful

Feb 15, 2013 | Speed Queen AWS52NW Top Load Washer

1 Answer

On the spin cycle, it makes a banging noice, rythmic, about 2 per second....only on the spin cycle... can you help???


The spin cycle is used to rid the water by centrifugal force. As the tub spins, the water iis forced out of the clothes. The banging noise comes from the weight of clothes being on one side making the load unbalanced. The machine will absorb some minor unbalancing. If it gets real loud & the machine starts dancing, shut the machine off by raising the lid, when tub stops, rearrange clothes.
Louie Almond

Mar 27, 2011 | Whirlpool Ultimate Care II LSQ9549L Top...

1 Answer

GWL10 leaving dark streaks on my cold water whites.


Hi Barla 2,Just read your posting.Now are the dark streaks like an oily substance?Is you machine leaking or has become noisier on the spin cycle?The only place this machine will get oil into the water is from the main bearings.But this is only the case if your main seal is faulty.Please reply with the additional information and I can help you rectify this problem.

Jun 22, 2010 | Fisher and Paykel GWL11 Top Load Washer

1 Answer

Water left in machine (clothes dripping) after delicate cycle


Hi,
Whirlpool is best in the standards of top loading washing machine when you are going for the front loading you can buy the IFB washing machine to get the better result

May 07, 2010 | Whirlpool Duet GHW9150P Front Load Washer

1 Answer

Clothing end full of lints when washed.


you have clothing like this:http://www.brandname-clothing.com/.
Otherwise,I think lints must be handwash.

Mar 22, 2009 | Kenmore 23822 Top Load Washer

1 Answer

Kenmore front load washer will not spin. Clothes come out wet.


The clothes are wet after spinning When the clothes are wet at the end of a cycle, check these:

Motor coupler
Spin cycle
Siphoning
Water-inlet valve
Motor coupler To test the motor coupler, re-start the washer in its spin cycle. Let the machine run for a minute, and then open the lid and notice whether the tub is spinning: 

  • If it's spinning when you lift the lid, the coupler is fine.


  • If it isn't spinning--and your machine was produced by Whirlpool®--you may have a broken coupler. Many Whirlpool-made washers use a small, relatively inexpensive device called a motor coupling. This plastic-and-rubber component is mounted to the shaft of the motor on one side, and to the transmission on the other. Over time, the coupler wears out and fails. When that happens, you need to replace it completely.


Spin cycle If the washer doesn't reach its proper spin speed, the clothes may be too wet at the end of a cycle. Check to be sure the load is properly balanced and run a spin cycle again. If the clothes are still wet, you may have a worn or loose belt (Maytag®), a worn clutch (GE®/Hotpoint®), or a worn motor pulley or tub bearing. Replace the applicable component. 

Alternatively, there could be clothes caught between the inner and outer tubs. Read the "It spins but won't pump" section of the "It won't drain" section. Also, there could be other things that cause friction on the drive train. Seek the assistance of a qualified appliance repair technician.

Siphoning If the water that pumps from the machine goes right back into the machine after the spin cycle, it may be because your washer is siphoning the water from a laundry tub with a slow drain, back into the washer. Try to improve the draining of the laundry tub. (Is there something stuck in the drain?) Also, be sure the drain hose doesn't reach more than about 4 inches into the laundry tub. If it does, cut off the excess.

Water-inlet valve Water-inlet valves eventually fail. One problem that may develop with a water-inlet valve is that it can no longer completely shut off when the electricity is turned off to it. Then, the valve may leak and drip water into the clothes tub--you may notice that your washer has water in it when you haven't used it for a few days. To fix this, replace the valve. 

Mar 02, 2009 | Kenmore 43142 Front Load Washer

1 Answer

No longer spinning/loud noise


Did all the standing water pump out?? If sou you may have broken a drive coupling

Jan 22, 2008 | Whirlpool Ultimate Care II LSQ9549L Top...

Not finding what you are looking for?
Whirlpool Duet GHW9150P Front Load Washer Logo

Related Topics:

46 people viewed this question

Ask a Question

Usually answered in minutes!

Top Whirlpool Washing Machines Experts

Dan Webster
Dan Webster

Level 3 Expert

8147 Answers

Richard Roth
Richard Roth

Level 3 Expert

9472 Answers

Mike Cairns
Mike Cairns

Level 3 Expert

3053 Answers

Are you a Whirlpool Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...