Question about Uniden Cordless Phone

2 Answers

I cannot use my phones since Saturday. The phone message on hand

The message on handset says handset 1 is on hold. I have gone outside to the phone box and I get a dial tone but no dial tone in the house on the phones. I cannot call out or receive calls. When I try calling from my cell phone to the house phone I get a busy signal. What can I do? I have tried unplugging the phones and waiting and plugging them back in with no luck.

Posted by on

2 Answers

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 1,800 Answers

Try to perform a soft reset.

Using:
menu/settings/ restore factory settings.

Posted on Dec 22, 2008

  • Level 1:

    An expert who has achieved level 1.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that has over 10 points.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 32 Answers

There is a loop coming from handset 1 causing the line to be busy on incoming calls.try removing the battery pack on this handset.i hope this helps

Posted on Dec 22, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Uniden D3098S I have 2 register hand sets #1 and #2 I have a 3rd one having trouble registerting it to the base iam 2 feet away from the base unit it says check base power & out of range


Registering a Handset


If you see a "not registered" message on a handset, you must register it to a base before using it.

1. On the base, open the menu and select "Register Handset"

2. On the handset, press and hold POUND (#) until the handset display says "Handset Registering" (about 2 seconds).

3. Wait until the handset display says "Registration Complete" (about 30 seconds), then pick up the handset and press eND/CleaR.

# If you don't hear a dial tone or the display says "Registration Failed" charge the battery completely, then try again.

May 12, 2016 | Uniden Phones

1 Answer

Both handsets have gone dead


Sadly that does happen tho not often .

Nov 14, 2015 | BT 4500 Cordless Phone - DECT - Satin...

2 Answers

Panasonic KX-T7730, we have a 824 phone system and cordless handsets (kx-tg1711) we cannot make outgoing calls on these handests but can take incoming calls and can transfer calls. how do we programme


  • Locate the program and auto-store button on your telephone. You will be using these to customize many of the features on your KX-T7730. The program button is used to enter or exit programming.

  • 2

    Program your outgoing line preference, i.e., the line you prefer to seize when you go off hook. Press "Program" "1" "1" "store" for no line. Press "Program" "1" "2" "Store" for an idle outside line. Press "Program" "1" "3" "Outside Line Number" "Store" for an assigned outside line. The outside line number will be a single or double-digit number that is set through your phone system.

  • 3

    Program your incoming line preference, i.e., the line you prefer to answer when you go off hook. Press "Program" "2" "1 "Store" for no line. Press "Program "2" "2" "Store" for ringing line. Press "Program" "3" "Outside Line Number" "Store" for an assigned outside line.

  • 4

    Program your flexible CO buttons. These are the inner row of 12 lighted buttons. Your outside lines need to be programmed to these--you can choose any of these 12 buttons in any order. Press "Program" "CO Button" "0" "Outside Line Number" "Store." The outside line number will be a single or double-digit number that is set through your phone system.

  • 5

    Program any other unused flexible CO buttons for an extension number or any frequently dialed phone number. Press "Program" "CO button" "1" "Extension Number" "Store" or "Program" "CO Button" "2" "9 + Phone Number" "Store". A "9" must be entered at the beginning of a phone number to tell your phone system to seize an outside line before dialing, e.g., "9-1-212-555-1234."

  • 6

    Locate the programmable feature buttons (the row of 12 solid buttons on the right). These buttons are basically one-touch buttons that can be set for extension numbers or phone numbers. Press "Program" "(PF) Button" "Extension Number" "Store" or "Program" "(PF) Button" "9 + Phone Number" "Store." Remember to press "Program" again to exit programming.

  • 7

    Locate your "FWD/DND" button. This button is used for setting "Call Forward" or "Do Not Disturb" on your telephone. To set call forwarding, go "off-hook" either by lifting the receiver or pressing speakerphone. Make sure you go to intercom and not an outside line. To forward all calls, go off-hook, press "FWD/DND" "1" "extension number" (the extension number that you wish to forward all your calls to) "#". After you hear a confirmation tone, place the receiver on-hook. The steps to set call forwarding for busy/no answer are the same as above, except you will press "2" in place of "1". To cancel call forwarding, press "0" in place of "1".

  • 8

    Program "Do Not Disturb," which stops your phone from ringing--any callers will just hear a DND tone. To program, go off-hook, press "Program" "4" "#" on-hook, to set. Press "0" instead of "4" to cancel.

  • 9

    Locate the message button--this works in coordination with your message light at the top right of your telephone. If the light is lit, press "message" to hear a message left to you either by another extension or a voice mail system. The message button can only be programmed as a message or one-touch button. To program as a message, press "Program" "Message" "3" "Store." To program as a one-touch, press "Program" "Message" "1" "Extension Number" or "Program" "Message: "2" "9 + phone number."

  • 10

    Return your KX-T7730 to its default settings by pressing "Program" "#" "*" "Store."



  • Read more: How to Program a Panasonic KX T7730 ' eHow.com http://www.ehow.com/how_7159736_program-panasonic-kx-t7730.html#ixzz1eYPzbevZ

    Nov 23, 2011 | Panasonic KX-T7730 Corded Phone

    2 Answers

    How do i turn off the silent mode on a uniden phone, ive held down the # sign and nothings happening


    Silent Mode
    You can silence the ringers on the base and all handsets for a specific period of time; the answering system answers any incoming calls without playing anything through the speaker.
    With the phone in standby, press and hold # on any handset. The phone prompts you to select the number of hours (1 - 9 or Always On) that you want it to stay in silent mode.
    To confirm, press # or just wait about 5 seconds. The phone turns on the answering system and displays Silent Mode On on each handset.After the selected number of hours, the phone automatically exits silent mode. To exit silent mode manually, press and hold # again.
    If the phone is in silent mode and you turn off the answering system, the phone exits silent mode.
    Multihandset Features To use the features in this section, you need at least 2 handsets.
    Your base supports a total of 12 cordless handsets: the one that came with the base and up to 11 DCX160 accessory handsets.You must register accessory handsets to the base before using them. (Handsets that came packaged with the base are already registered.)Handsets that aren't registered display a Not Registered message. For registration instructions, see p. 18, or see the accessory handset manual.If a handset was ever registered to a base, you must reset it before it can register to a new base; see p. 18, or see the accessory handset manual.Conference Calling
    When an outside call comes in, two handsets can join in a conference call with the outside caller.
    To join a call that's already in progress, just press Talk/flash or SpeSpeSpeaker.To leave the conference call, hang up normally; the other handset remains connected to the call.

    Aug 18, 2011 | Uniden DECT 2080-5 Quint Phone

    1 Answer

    Pick up receiver and get a dial tone for outgoing w/o pressing 9


    I beleive you are referring to a phone which is part of a PBX system or Key-system (sounds more like a Panasonic PBX system). If so, this is a system program that has gone "bonkers". You may need to re-program the automatic outside line dial tone on the system for the specific phone you are referring to.

    Jan 28, 2009 | Panasonic KX-T7030 Corded Phone

    1 Answer

    Delete messages


    This is from the manual.

    Erasing Messages
    You may erase messages in the following three ways:
    To erase a message while it is playing
    1. Press and release PLAY/STOP button.
    2. Press the review and skip buttons to select and play the message you want to erase.
    3. Press the delete button, the current message is erased, and the next message plays.
    To erase all previously played Messages in a mailbox
    1. Make sure the phone is OFF (not in talk mode)
    2. Press and hold the delete button until "ALL OLD MESSAGES ERASED" is announced.
    To erase a message from the handset :
    1. Press the flash/answerer button on the handset
    2. Press the play/stop (key 2) on the handset.
    3. Press the erase (key 0) on the handset to erase a message during playback.
    NOTE: Erased messages cannot be restored.

    Jan 08, 2009 | GE 28112 Trio Cordless Phone

    2 Answers

    Deregister lost or broken phones


    Some tricks from a helpful Uniden rep:

    holding down end+# keys at the same time on the phone for about 10 secs (you will hear a beep) will deregister the handset. If you have a dead handset and want to deregister it from the base, you have to reset the base. unplug the phoneline and power. hold down the "delete message" key, plug power back in. about 10 secs later, you will hear a long beep (theres a short beep upon powerup as well). At this point all handsets are deregistred and you will have to reregister them with the end+# trick. this way when #1 handset is dead, you can make a working one #1 and get the broken one fixed emotion-1.gif

    BTW, this is a woot warranty, not uniden warranty. however the uniden rep gave me the number to the people who refurb (rox0rz!) these. I'll post an update when I finally get ahold of them (and the number if its actually helpful)

    Jun 20, 2008 | Uniden TRU8885 Cordless Phone

    1 Answer

    Indicator message light on handheld phones do not go off!!!


    on the base set, press and hold the voice mail 1 button. You will get a message clear voice mail indication? hit the sel/save button to the left of the display.

    poof! message gone

    Apr 17, 2008 | RCA ViSYS 2-Line Speakerphone

    1 Answer

    Vtech M6896 phones do not work


    Step 1: Press and hold FIND HANDSET on the main telephone base for 10 seconds.

    Step 2: When the IN USE light starts to flash, release the FIND HANDSET button.

    Step 3: Press and release FIND HANDSET again. The IN USE light will turn off and in a few seconds, all handsets will be de-registered.

    Step 4: All handsets will show NOT REGISTERED.

    To register a handset (register 1 handset at a time):
    Step 1: Place the handset in the base unit or a charger that is connected to a power outlet. If PRESS FIND HNDST 4 SEC ON BASE does not appear on the screen after a few seconds, lift up handset and place in base or charger again.

    Step 2: On the telephone base, press and hold FIND HANDSET for four seconds. Release FIND HANDSET once the IN USE light comes on.

    After a while the handset will emit a series of tones, the newly registered handset will be assigned the lowest extension number not previously assigned to another system handset (1-4) when successfully registered. Repeat Steps 1 and 2 if the handset does not successfully register to the telephone base within two minutes.

    Jan 18, 2008 | Vtech mi6896 Trio Cordless Phone

    4 Answers

    Programming instructions for used phone


    Program Thomson Consumer Electronics (GE?) 2-9316A Speaker Phone (what we found works)
    To program:
    1. press speaker or lift handset.
    2. press STORE
    3. dial the number to be stored
    4. press MEMORY DIAL
    5. press location (0-9 on keypad or 1 of the 3 emergency quick dial)
    6. press speaker or hangup.
    To dial emergency numbers:
    1. press speaker or lift handset.
    2. press any of 3 emergency quick dial
    To dial stored numbers:
    1. press speaker or lift handset.
    2. press MEMORY DIAL
    3. press location (0-9 on keypad)
    Does anyone know how to add PAUSE in a stored dial string?

    Aug 27, 2007 | GE Corded Speakerphone with 2 Cordless...

    Not finding what you are looking for?
    Uniden Cordless Phone Logo

    308 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Uniden Phones Experts

    kakima

    Level 3 Expert

    96467 Answers

    Dave Ellis

    Level 2 Expert

    84 Answers

    k24674

    Level 3 Expert

    7987 Answers

    Are you an Uniden Phone Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...