Question about Whirlpool Ultimate Care II LSQ9564J Top Load Washer

4 Answers

Whirlpool imperial series 2 ultimate care washer

My washer started out not spinning. now it fills up agitates the load, then stops on the rinse cycle.then it will not drain or do anything.please help.

Posted by on

  • 5 more comments 
  • Anonymous Nov 11, 2007

    I have Imperial series clean touch washer and the agitator suddenly stopped and water drained out, I tried again to fill with water, at the level water sopped but the agitator wouldn't start and water drained off. What could be the problem?

  • pratapgandhi Nov 11, 2007

    i have Imperial series clean touch clothes washer from whirlpool and the agitator stopped suddenly and water drained out, tried again to fill with water, it reached it's level but the agitator didn't start and water drained out, what could be the problem?

  • skilled Dec 02, 2007

    after the wash cycle, it only drains about half the soapy water before it stops draining... and fills with rinse water. so you never get a complete rinse and clothes feel and smell like soap.

  • dive_syko Mar 01, 2008

    Exact same problem. After agitate mode machine won't go into rinse mode.

  • thastlc Mar 13, 2008

    My washer will occasionally not spin all of the water out at the end of the cycle. Right now I am able to run it through the spin only cycle and it will spin the remaining water out. Any ideas on why it will sometimes do this? (I have the same load amount in each load)



    Thanks!



    Tammy

  • jfriend13 Dec 29, 2008

    The washer stops at the rinse and spin cycle. Now it is full of water and will not drain or spin or empty. Plus there is a funny odor coming from the machine. I think it might be the motor is bad. Your opinion.

  • Anonymous Apr 14, 2009

    My washer does not stop filling up

×

Ad

4 Answers

  • Level 1:

    An expert who has achieved level 1.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 1 Answer

I had the same problem with this washer. It was the lid switch.

Posted on Dec 01, 2009

Ad
  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

I also had the lid switch problem. I got it to work by messing with it for a few seconds.

Posted on Jul 07, 2010

Ad

Jewel 42  I had a similar problem with mine, it wouldn't drain or spin.  It was the sensor/lever that lets the machine know that the lid is closed... the screw casing that held it in place had broken... I tied it back in place covered the string with duct tape and now it works fine... or at least it did until the pump cracked this week.

Posted on Feb 28, 2008

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 1,462 Answers

Check filter and check no foreign object in pump impellor.

Posted on Apr 10, 2007

2 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

  • 4 Answers

SOURCE: My whirlpool imperial ultimate care fills with

Problem with PCB, please call service Engineer.

Posted on Sep 16, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have a Whirlpool Ultimate Care 2 Imperial Series washer that doesnt spin out very well. It will sometimes spin out but leaves the clothes very damp. Sometimes the washer will try to spin itself out but ...


First thought is that the cycles are off.we have the same problem with ours right now. That slow spin speed concerns me. The motor could be going bad. If this washer is 10-12 years old, you may want to look at replacing it. Does the machine ever start agitating before it finishes filling. If so, the cycle mechanism is going bad. This has a whole host of potential problems. Ave a rep look at it. He can narrow it down quickly.

Feb 06, 2013 | Whirlpool Washing Machines

1 Answer

How do I repair my Whirlpool Ultimate Care 2 LSQ9549L Top Loader Washer?


check the motor coupling,if the coupling is broken you'll hear the motor run but the agitiator won't move and no spin,the coupling connects the motor to the transmission.watch this video
http://www.youtube.com/watch?v=9K1KHEogf3c

May 30, 2012 | Whirlpool Ultimate Care II LSQ9549L Top...

1 Answer

I have an whirlpool ultimate care II Imperial Series Model # LSN2000JQ2 Serial:CM2819491 Type: III That will fill but won't agitate. Is this something I can really fix on my own?


Could be a problem with the lid switch or motor coupling. Does it drain? Does it spin?
when its time to agitate or spin, do you hear the motor?
Lets start with the lid switch. open the lid and use a screw driver to push the switch down. pay attention to see if you hear it click. Try to run the unit with the screw driver holding down the switch.
Let me know what happens so I can further assist you.

Feb 20, 2011 | Whirlpool Ultimate Care II LSQ9564J Top...

1 Answer

Whirlpool top load washer no low-speed agitation. The unit fills, starts the wash cycle with normal agitation, but after a few minutes it just sits there soaking until the it's time to drain/spin. Drains...


Either the wire going to motor for non working speed is loose or damaged, or motor is bad. It could also possibly be timer not sending power to motor for that speed.

Sep 27, 2017 | Whirlpool Ultimate Care II LSQ9549L Top...

1 Answer

Will not spin on any rinse cycle


Hi, This washer does not have a belt. While the washer is agitating, if you lift the lid will it stop? Some models will agitate but not spin if the lid is up. It sounds to me like the lid switch might be going bad.
If you will get me a model #, I can look this up for you and give you a better idea.

Vic

Jul 05, 2009 | Whirlpool Ultimate Care II LSQ9549L Top...

1 Answer

Stops in the middle of wash cycle


Hi!

If the cycle doesn't advance, it's probably the timer or a cold-water supply problem:
It's the timer, if your washing machine fills with water and begins agitating, but the timer never advances--or if the washer is in a spin cycle and the timer won't advance. Then you need to replace the timer.
It may be a cold-water supply problem, if the washing machine fills with water, agitates, drains, and spins, but then doesn't fill with rinse water. See There's no cold water.
Please do rate this solution as FixYa and revert for further assistance.

Thanks
Rylee

May 29, 2009 | Whirlpool Ultimate Care II LSQ9549L Top...

1 Answer

Whirlpool Ultimate Care II


sounds like a broken coupling.
it probably don't agitate either.

Oct 28, 2008 | Whirlpool Ultimate Care II LSQ9564J Top...

2 Answers

Agitator


if its a 2 piece agitator.. the gears in top of agitator is stripped out.. change gears be like new....spin top countor clockwise if it dont grap.. gears bad

Sep 28, 2007 | Whirlpool Ultimate Care II LSQ9549L Top...

Not finding what you are looking for?
Whirlpool Ultimate Care II LSQ9564J Top Load Washer Logo

5,629 people viewed this question

Ask a Question

Usually answered in minutes!

Top Whirlpool Washing Machines Experts

Sal De

Level 3 Expert

2699 Answers

Marvin
Marvin

Level 3 Expert

83772 Answers

Gerry Harvey
Gerry Harvey

Level 3 Expert

1474 Answers

Are you a Whirlpool Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...