Question about RCA 257003 Remote Control

1 Answer

TV in SAP mode and cannot remove. Lost original remote.

Had a power surge that knocked out my dvd/vcr(it was fried) and the tv was temporarily disabled. When the TV was cut back on some of the channels (that were spanish broadcast) got knocked into SAP mode and those that were not do not have vocal sound but has the music and other sounds. The channels that are not broadcast in spanish are alright. I lost the original remote and do not have a universal remote that has a SAP button on it. Is there a way to reprogram the TV without the remote. I have a RCA Model 27V513T/Serial Number F354CC09F/Service number 27V513TYX1. I would really like to get a remote with a SAP button and the instructions booklet to go with it or figure out how to get my TV back to normal. URGENT PLEASE CALL ME AT 512-897-7204 AFTER 12/23/08. I would like to get this straight before Christmas.

Posted by on

  • xxtaylor79xx Feb 10, 2009

    Anyone got ideas on universal remote with SAP ??? tv sylvania 6724FDF

×

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

I had the same problem. You have to order a replacement remote with the MTS button (Multi Channel Sound)
Call RCA Support @ 1.800.338.0376 I believe the remote part number is RCR130TB1

Posted on Jan 08, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do i program my remote


Hello;

Without knowing the codes for the specific brand names and models of your devices, this is how you program the Zenith MBR3447 for your TV, VCR, DVD Player, CD Player or Audio Receiver:

TV

1. Push the "Power" button on the TV to turn it on.
2. Press and hold the "PRG" button in the upper left corner of the remote. Release when the indicator light, located in the top center of the remote control, comes on.
3. Push the "TV" mode key located at the top of the remote.
4. Enter 0 -- 0 -- 0 on the remote's number pad, then press the "Enter" button.
5. Aim the remote control in the direction of the TV's IR sensor and push the "Power" button. Pause a second. If the TV fails to shut off, push the "Power" button again. Repeat until the TV does shut off. Each time the "Power" button is pressed the Zenith MBR3447 tries using a different TV device code from its code library to turn the TV off. Therefore, when the TV finally does shut off it's an indication that the remote is temporarily programmed with the correct device code to control the brand of TV you're using.
6. Press "Enter" to save the current code.

VCR

1. Push the "Power" button on the VCR to turn it on.
2. Press and hold the "PRG" button in the upper left corner of the remote. Release when the indicator light, located in the top center of the remote control, comes on.
3. Push the "VCR" mode key located at the top of the remote.
4. Enter 0 -- 0 -- 0 on the remote's number pad, then press the "Enter" button.
5. Aim the remote control in the direction of the VCR's IR sensor and push the "Power" button. Pause a second. If the VCR fails to shut off, push the "Power" button again. Repeat until the VCR does shut off. Then press "Enter."

DVD Player, CD Player or Audio Receiver

1. Push the "Power" button on the device your programming the remote to control to manually turn it on.
2. Press and hold the "PRG" button in the upper left corner of the remote. Release when the indicator light, located in the top center of the remote control, comes on.
3. Push the "AUX" mode key located at the top of the remote.
4. Enter 0 -- 0 -- 0 on the remote's number pad, then press the "Enter" button.
5. Aim the remote control in the direction of the device's IR sensor and push the "Power" button. Pause a second. If the device fails to shut off, push the "Power" button again. Repeat until the device does shut off. Then press "Enter."

Mar 11, 2011 | Zenith MBR3447 Remote Control

4 Answers

MAGNAVOX UNIVERSAL REMOTE


hi have you tried scanning all codes with the remote untill it picks up the correct signal if you have the manual it will tell you how to do this if its possible it will work after searching the codes.
Also what model remote and what make cable box

Mar 29, 2008 | Philips Magnavox Learning Universal Remote

2 Answers

How to use your control with my dvd player


Hello chegui59, my name is Michael Hurst with DISH Network. There are 2 ways of programming your remote to your DVD player. You can use a remote code for your DVD player. In order to give you the right remote code I would need to know the manufacture of your DVD player and the model of the remote that you have. You can also try a Power Scan to get the DVD player programmed into your DISH remote, here are the steps: Withthe desired equipment on, press and hold the correct mode button until all modebutton backlights illuminate, then release. Press and release the Power button. AUX Mode: Before pressingand releasing the Power button. Press 0 for a TV, Press 1 for a VCR/DVD andPress 2 for any other device. Then Press STAR (*). Press the Up button once asecond while pointing the remote at the desired equipment. If the code for theequipment comes up, the equipment will power off. Press the POUND (#) button. Ifthe code entered is valid for the remote, the mode light flashes three times.

May 29, 2010 | DISH Network IR Remote Control

1 Answer

Lost original remote t the symphonic tv which has


You can get the original remote for a decent price. It is an original replacment remote. You can find it at any of these places.

www.replacementremotes.com

remotes.com

www.mr-remote.com

www.neworiginalremotes.com

You will need the original remote to access the features you want to use.

Nov 23, 2009 | RCA DIRECTV Satellite Remote Control

1 Answer

How do i program this remote to a mitsubishi tv?


  • Manually turn on the device you wish to scan for (e.g. TV)
  • Perform Power Scan by pressing and holding (approximately 3 seconds)the desired DEVICE MODE button TV, VCR, CBL, DVD or SAT until the status indicator light begins to blink.
  • Press and release the PWR (power) button. The status indicator light will stop blinking and stay ON at this point.
  • Press and release slowly and patiently the blue UP ( ? ) button to scan forward through the code database. To scan backward through the code database, press and release the blue DOWN ( ? ) button. Each time you press the up or down arrow, the remote will try and turn off the device (TV, VCR etc) you originally selected.
  • When the device (TV,VCR etc.) responds by shutting off, press the ENTER button. This will store the code
  • in memory and you will see three blinks of the status indicator light to confirm the code input. Be patient, there are over 100 codes to search through.

Oct 20, 2009 | Big Button TV Universal Remote

2 Answers

I have lost my remote


Original and replacement remotes: www.remotes.lt

Sep 07, 2009 | Remote Controls

1 Answer

Lost codes


http://www.hifi-remote.com/ofa/codes-tv.shtml#tv

If none of the codes work then we have two other solutions:

1. Searching For Your Code

If you have tried all of the set-up codes for your brand of equipment ,or yourbrand is not listed, and you are still not able to get the unit to respond, trythe following procedure to search for your code.
If you don't find a code that works, the remote will flash four times when youreach the end of all the codes for this device type.
  1. PRESS the button for the device you want to program, (TV, VCR, CABLE, etc.), then RELEASE.
  2. PRESS and HOLD the SETUP button until the red LED flashes twice, then RELEASE.
  3. ENTER 9-9-1 (two blinks on the remote)
  4. ALTERNATE slowly between the POWER key and the DEVICE (TV, VCR, CABLE, etc.) button until your device turns off. (On VCR, LD, and CD players use PLAY instead of POWER)
    Make sure that the remote is pointed at your device during the search, You may have to press this sequences of buttons up to 100 times to search the entire library of codes.
  5. When your device turns OFF, PRESS the SETUP button and RELEASE it to lock in the code for your device.

2. Learn the buttons from the original

Line up your original remote and the head-to-head before completing thefollowing steps.
  1. PRESS and HOLD the SETUP button until the red LED flashes twice.
  2. PRESS 9 - 7 - 5, the red LED will flash twice.
  3. PRESS the DEVICE key where you wish to learn the function. The next 3 steps must be completed within 10 seconds.
  4. PRESS the button that will receive the learned function, the LED will flash rapidly.
  5. PRESS the button on the original remote to be learned.

Now you can repeat steps 3 through 5 to learn other functions onto other keysor press and hold SETUP until the Cinema's red light flashes twice to lock inyour new feature. (If the red light does not blink twice, stop and repeat stepsthrough 6).
To test the new feature, press and release the device key in which the newfeature was learned followed by the key on which the feature was learned

More help for programming your remote can be found here:
http://www.hifi-remote.com/manuals/ofa-l.shtml?URC-7800#device

Hope that helps! Should you have any further questions,please feel free to post them here.
Television Video - DVD Audio Satellite Set Top Box Video - VCR Brand: Model (optional): clip_image001.gifclip_image001.gifWe could not find an exact match, we think this code will work. 10054 clip_image001.gifclip_image001.gifSetup Instructions
· Set the "Mode Switch" to TV.
· Press and hold the "Mute" button and the "Select" button until the visible LED blinks twice.
· Enter the 5 digit Code above.
· Try your new code and tell us how it worked!
You'll have to settle for that, use the middle power key in the tv device to power on & off the tv.


hope this may help;

Regards,
VOTIT

DON'T FORGET TO RATE;

Aug 28, 2008 | Philips Magnavox Learning Universal Remote

1 Answer

Tv codes


Hello, Well I have a Phillips universal remote but but maybe they are the same. For the Orion TV try 105, 115, or 713. For The Pioneer DVD Try 042. If one or more does not work, Look for a "code Search" button. Turn on the device, then push and hold down the code search button until the red indicator stays on, then release the search button. Press and quickly release the desired mode button (TV, DVD, etc). The red indicator blinks off once. . If it is a tv or vcr use the channel up button until the channel changes. Press the power button on DVD and see if it is right Hope this helps.

Mar 16, 2008 | Philips Magnavox REM-350 Remote Control

3 Answers

TV remote codes


1000,1001,1002,1003,1004
MAGNAVOX and 0000,0001,0002,0003,0004
0057 PHILIPS and 0005,0006,0007,0008,0009

Dec 08, 2007 | Polaroid 1720-7 Remote Control

4 Answers

URC-3021B00


PROGRAMMING DEVICE CONTROL
The One For All 3 Device Universal Remote Control is preprogrammed at
the factory to operate an RCA TV, a Toshiba DVD player, and a Motorola
cable box.To control devices other than the default brands,perform the following
steps; otherwise skip this section:
1. Turn on a desired device (e.g.,VCR or DVD player) and, if
applicable, insert media (e.g., cassette or disc).
NOTE: Please read steps 2 through 4 completely before proceeding.
Highlight or write down the codes and device you wish to program
before starting step 2.
2. On the remote control,press a device key once (i.e., DVD/VCR,
CBL/SAT,or TV).
NOTE: To program control of a VCR, PVR (or DVR),TV/VCR Combo,
or TV/VCR/DVD Player Combo press DVD/VCR once.After programming
a VCR Combo device, you will be able to control channel selection,
volume, and VCR functions.
NOTE: To program control of a DVD Player,DVD Player/VCR
Combo, or TV/DVD Player Combo, press DVD/VCR once.After programming
a DVD Combo device, you will be able to control channel
selection, volume, and DVD functions.
NOTE: To program control of a Cable Box, Cable Box/PVR (or DVR)
Combo, Satellite Receiver, or a Satellite Receiver/PVR (or DVR)
Combo, press CBL/SAT once.
3. Press and hold SET until the LED (red light) blinks twice,
then release SET.
4. Use the Manufacturer’s Codes (starting on page 18) to
locate the type of device and brand name and then enter
the first four-digit code for your device. If performed correctly,
the LED will blink twice.
NOTE: If the LED did not blink twice, repeat steps 2 through 4 and enter
the same code again.
5. Aim the remote control at the device and press POWER
once.The device should turn off. If it does not, repeat
steps 2 through 5, trying each code for your brand until
you find one that works. If it still doesn’t work, try
Searching For Your Code on next page.
NOTE: If the device does not have a POWER key, press PLAY.
6. Repeat steps 1 through 5 for each device you want to control.
For future reference,write down each working device

Here is a link to your manual:
http://www.ofausa.com/remote_manual/CTGA...

Nov 26, 2007 | One For All URC-3021 Remote Control

Not finding what you are looking for?
RCA 257003 Remote Control Logo

1,987 people viewed this question

Ask a Question

Usually answered in minutes!

Top RCA Remote Controls Experts

The Knight
The Knight

Level 3 Expert

68250 Answers

andy williard
andy williard

Level 2 Expert

226 Answers

Cindy Wells

Level 3 Expert

4756 Answers

Are you a RCA Remote Control Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...