Question about Plumbing Pumps

1 Answer

I just placed my order for a hydrolic jack. I went through all the steps and paid then was kicked off the site. Did my order go through or not? Joan Cline

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 10 achievements.


    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 547 Answers

Call you card provider and thay will beable to tell you if it did or not .thank you for useing fixya please rate me

Posted on Feb 12, 2009

Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

Only one yearold;turn on,or plug in kicks breaker

Roger, DO NOT USE. Return to place of purchase, or cut cord and discard.

Apr 24, 2015 | Utilitech 0.33-HP Thermoplastic...

1 Answer

Went to prime my FP4022 Shallow well pump and the mottom was seperated at the joint line. It did not get exposed to freezing and was drained for the winter and stored. Can you replace just the pump body ?...

Yes, you can, although it might be half or more of what you paid for the pump. First you have to make sure nothing is cracked, it separated for a reason. My gut is telling me that there was some water hidded in there and it froze. If that is the case, throw it away. I found this website that has most of the parts for it.

Hope this helps. Good luck.

Apr 19, 2011 | Flotec Corrosion Resistant Shallow Well...

1 Answer

I replaced my pressure switch with a Square D FSG2j24M4CP. Last night when the iron genie went into it's regeneration cycle the pressure switch snapped off. Should I be using a different type of pressure...

The problem is that the pressure switch is not adjusted properly...
You need to turn the taller screw down so that the pressure switch kicks the pump on sooner...

This tip will help you with that...

Well Pressure Switch Adjustment Water Well Problems


Jul 14, 2010 | Square D FSG2J24M4CP Water Pump Pressure...

1 Answer

How do I determine whether it is the switch or the capacitor that is the problem on my Delta sander model # 31-080? These are both expensive parts and together would cost more than 1/2 of the retail price...

If you can get at the connections for the switch you can do a continuity test on the switch. If the switch has continuity when on then it's most likely good.

Jun 11, 2010 | Plumbing Pumps

1 Answer

Hydrolic lift. Fluid is leaking from breather

Hydraulic lift seal needs to be replaced so that the fluid
will not be pushed out. Okey, God bless you.

Oct 12, 2009 | Plumbing Pumps

1 Answer

Jacks stalls 1/2 way up

try opening the hydrolic oil "fill" plug to let air in...Your jack came with a vented plug,for you to put on after oil doesn't leak while being transported...I hope this helps,...1nglen

May 04, 2009 | Plumbing Pumps

1 Answer

Floor jack needs sevice or seal replacement

you can do it two ways remove and match up the seals with a local distrubuter or try to find your make and model and order them.check your oil level also and the valve for dropping.

Apr 02, 2009 | Plumbing Pumps

Not finding what you are looking for?
Plumbing Pumps Logo

Related Topics:

81 people viewed this question

Ask a Question

Usually answered in minutes!

Top Plumbing Pumps Experts

Jay Finke
Jay Finke

Level 3 Expert

1222 Answers

john h

Level 3 Expert

7133 Answers

Brad Brown

Level 3 Expert

13530 Answers

Are you a Plumbing Pump Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides