Question about Whirlpool SF368LEPS Stainless Steel Gas Kitchen Range

1 Answer

Whirlpool sf368leps have to set for 450 degree to get it up to 300 is their a setting on control panel to take care this

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 6 Answers

Can hold down bake the and adjustment comes up can adjust in 10 degree steps 30 degree up and 30 degree down use the temp up and down to make the adjustments

Posted on Dec 23, 2008

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Whirlpool RBS245PDS18 temperature calibration?


If it is new contact the people that sold it to you for warranty repair. If not Just set it higher, that is a lot lest costly then getting the appropriate equipment to calibrate it. You can also replace it.

Dec 19, 2014 | Whirlpool Ovens

1 Answer

What's an f1 and f2 code mean???


Hello,

The F1 code means that a button on the touchpad is stuck

The F2 means that the oven tempature was at least 100 degrees over what the temp it was set to was

the F1 will come sometimes if the ribbon connection on the touchpad doesnt fit well into the control board and other times it comes because the touchpad is defective

the F2 comes up because the control has measures the temp and thinks that when it set as lets say fro instiance 350 degrees the control thinks the temp ahs reached 450 degrees(100 plus over) typically the thing wrong when the F2 comes up is the oven sensor at room temp to be between 1060-1100 ohms

However if you are getting both error codes at the same time the only thing common to both is the oven control and if both at the same time i suspect the control is the problem

GENE

Sep 06, 2011 | Whirlpool Kitchen Ranges

2 Answers

Error F5E1 after self cleaning


Hi There
I have read the codes you are looking for,so I'm sending them to you and i hope this will help.
F5 E1 16 Door latch not operating Check that door switch is completely closed. Check latch, solenoid, and actuation switch for electrical or mechanical malfunction.Thank you for writing to fix ya.
Best regards Richard

Dec 11, 2009 | Whirlpool 30" Self-Cleaning Freestanding...

2 Answers

My Whirlpool oven no longer heats to the set temperature.


Temp probe/thermometer inside oven dirty, or off attachment, or defective. On some models, a small screw head adjustment is provided to calibrate thermometer under dial knob. Else, I would just set dial 50 degrees higher rather than expense of new thermometer or dial.

Mar 02, 2009 | Ovens

2 Answers

How to remove the control panel on Whirlpool double oven Model RBD305PDS14


Remove the doors by turning toward you a little toggle apparatus located on each hinge. Locate a small screw on the lower inside edge of the left and right hand trim and then slide off the trim. Remove the lower trim then raise the upper trip and put the left end of the panel inside the top opening. This allows you access to the control panel. Test both the keypad part #8300440 and the control panel part #830219 to see which one needs to be replaced. Order the replacement part, plug it in, reverse the precess above and it should work like new..

Oct 02, 2008 | Whirlpool RBD305PDS Electric Double Oven

1 Answer

Water leaking from whirlpool washer


facing the washer locate the two screws. They will either be in the front or rear of the control panel and back them out far as you can. Once you have done that pull the control panel slightly forward, and tilt it back on the hinges. Now unplug the lid switch wire but don't forget to plug it back when your done. Next locate at the rear of the washer body the two gold clips then push forward, and take careful note of how they fit. Then pop them out with a screw driver tilt the washer body forward at 45 degree angel and walk forward with the body, and set it down.

Jan 12, 2008 | Whirlpool Ultimate Care II LSQ9549L Top...

1 Answer

Whirlpool 465 oven temp


Go to Calibration mode and adjust the temperature up by 10, 20 or 30 degree. This is in each manual.

Jan 11, 2008 | Whirlpool GS460 Gas Kitchen Range

Not finding what you are looking for?
Whirlpool SF368LEPS Stainless Steel Gas Kitchen Range Logo

Related Topics:

167 people viewed this question

Ask a Question

Usually answered in minutes!

Top Whirlpool Kitchen Ranges Experts

Dan Webster
Dan Webster

Level 3 Expert

8205 Answers

Ismael Rodriguez...

Level 2 Expert

162 Answers

Cindy Wells

Level 3 Expert

4885 Answers

Are you a Whirlpool Kitchen Range Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...