Question about Olympus Stylus 700 / 700 Digital Camera

1 Answer

Stylus 700 error D:5f08 5e02

When you turn the camera, the lens tries to focus several times, then you get error message D:5f08 5e02
Occasionally the camera will work normally and take a photograph, and also show photos taken, but will give the error message if you try to download the pictures to a computer.

Posted by on

  • 1 more comment 
  • hhalosg Dec 25, 2008

    I have the same problem, is there anyone can solve this problem?

  • robinpirkko Jan 08, 2009

    Guy at the camera shop said a new camera is a better option, repair would only be a little less.

    Somehow I doubt the new one will be Olympus.

  • Neusa Liquito Aug 26, 2013

    i have the same problem. Can any help ?

×

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 2 Answers

The error message (D: 5f08 5e02) means that your lens is dying / dead. It just happened to mine (on the Mju 700, but it's the same thing) and I was told that it could be repaired, but it would cost as much as a new camera. I've only had mine 2 years and I've been really careful with it, so I'm a bit annoyed, but I have used it a lot!

Posted on Jan 05, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Lumix DMC-ZR1


This is a lens mechanism fault. USe can of air and spray on surrounding the lens For cleaning the dust. and then try.

Aug 05, 2012 | Panasonic Lumix DMC-FZ28 Digital Camera

1 Answer

Olympus 700 error code 5e02 The camera lens goes out and back in on switching on, then shows the error code.


try these:-
  • connect it to pc and on it
  • vaccum the barrel of lens
  • changing mem. card and batt. for 2min.
  • shake it.
  • on and off in different positions
  • hit the part near lens softly with palm (trust me this made mine work)

Mar 16, 2010 | Olympus Stylus 700 / 700 Digital Camera

1 Answer

Fuji a500 give "focus error" message and won't shoot pictures


I am sorry to say that this design of lens is the worst i've seen from Fuji.
Focus error relates to the mechanism right at the front of the lens. The motor and drive gear are in the end piece of the lens, as opposed to other cameras that have the focus mechanism in the back of the lens and is easily access able once inside the camera.
Does the lens stick? or buzz on power up? If you tap gently, with your finger nail, on the actual lens on power up ( you may have to do this several times) you may find the lens comes out ok and no error msg is displayed (until you try zooming).This will probably be because something is jamming the gears or the tiny tension spring used on the gears has come off. I have tried to clear several A500's with this problem with limited success.

Jun 23, 2009 | Fuji FinePix A500 Digital Camera

1 Answer

Zoom Error, Lens won't close


There are several causes for this to happen.
1. The lens assy is out of alignment and stuck; stalling the motor.
2. The motor itself is defect
3. If you can hear the motor working , then it will be a stripped plastic gear between motor drive and lens assy.
DIY repair not recommended (possible)

Mar 07, 2009 | Fujitsu Digital Cameras

2 Answers

Camera olympus error D: 5f08 5e02


The error message (D: 5e02) means that your lens is dying / dead. It just happened to mine and I was told that it could be repaired, but it would cost as much as a new camera. I've only had mine 2 years and I've been really careful with it, so I'm a bit annoyed, but I have used it a lot!

Dec 06, 2008 | Olympus Stylus 700 / 700 Digital Camera

2 Answers

OLYMPUS DIGITAL ALL WEATHER


1) Make sure that the batteries are in good condition
2) Check and clean any dirt or corrosion from the battery terminals.

If the power supply voltage suddenly drops during initialization,
or when the lens is trying to extend itself, it could produce this
kind of error.

3) Make sure that the lens extension tubes are not mechanically
jammed.

4) Remove the batteries, turn the unit ON and wait for it to fully
discharge any internal capacitors, then put the batteries back
and try to turn the unit back on. This should fully RESET the
internal CPU.
===

Generally this kind of error means that the camera's internal
computer is trying to activate the lens zooming motors, but
the motors fail to move as expected.

Other causes could be:
a) burned out ZOOM motors
b) burned out motor drive circuitry
c) bad motor positioning sensor
d) defective computer components
e) failed internal firm-ware.

none of these cause are user fixable.

Hope this helps
Martin

Nov 10, 2008 | Olympus Stylus 700 / 700 Digital Camera

3 Answers

Olympus u 700


In on postion in camera mode,the lens seems to move in and out,blurring the image and then stops with this message on screen. D: 5f O8 5eO2

Jun 26, 2008 | Olympus Stylus 710 Digital Camera

6 Answers

Blue screen error code


the lens open halfway, the picture on the LCD is blurry and one second after the lens close and an error appears of the screen saying "D: 5f08 5e02". what does this mean??? can you help me fixed this one??

Oct 13, 2007 | Olympus Stylus 700 / 700 Digital Camera

1 Answer

Blue screen and error message


No solution you can make- The motor mechanism is shot Depending on how long you have had the camera you may get it replaced or a repair price quoted. The repair price will be horrific buy the next camera.

Sep 28, 2007 | Olympus Stylus 710 Digital Camera

Not finding what you are looking for?
Olympus Stylus 700 / 700 Digital Camera Logo

1,456 people viewed this question

Ask a Question

Usually answered in minutes!

Top Olympus Digital Cameras Experts

kakima

Level 3 Expert

96467 Answers

Willem.
Willem.

Level 2 Expert

345 Answers

Donald DCruz
Donald DCruz

Level 3 Expert

17129 Answers

Are you an Olympus Digital Camera Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...