Question about Kenwood KVT-719DVD 7 in. Car Monitor

1 Answer

I connect my kenwood kvt 719dvd and get a protect message

I checked my speaker wires and can not find a short.

Posted by on

  • 1 more comment 
  • SURFNTURFER Feb 06, 2009

    i also have this problem , i have disconnected all the speaker wires to the unit and still get the code. i have checked continuity from all the speaker wires they all check out fine ,there are no chassis shorts or bare wires. i think the unit is shot i hope not they aren't cheap . someone ,anyone , please help me !!!!!!!!

  • Anonymous May 18, 2009

    i have the same problem kenwood says it could be the wires but it could also be iternal problem they fix it for free if you have warranty

  • Anonymous Mar 27, 2014

    problema monitor y cerebro

×

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 15,935 Answers

Did you check continuity to ground with each speaker wire?
Have it bench tested at a local shop to eliminate or identify the unit as being at fault.

Posted on Dec 22, 2008

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Pass code to Kenwood kvt 717 without remote


Without a remote control, you can't. Just buy an original or a suitable universal remote control that have set-up code/s for your device, in its code list. If you wish to get more details visit the sites linked here.
http://remotesearch.blogspot.com/ http://electrohelponline.blogspot.com/

Jan 05, 2017 | Kenwood Car Audio & Video

1 Answer

I need instrution manual for kenwood model number ew7507ek


Do you mean the Kenwood EW7507EK electric oil-filled heater? ManualsLib has this manual here: https://www.manualslib.com/manual/86348/Kenwood-Ew7507ek.html#manual .

I hope this helps.

Cindy Wells

Jan 05, 2017 | Kenwood Car Audio & Video

1 Answer

I have a boss 400w riot 2-4 channels,how do i connect the high level wires? Because stereo doesn't have rca's


to use the high level leads, you have to isolate the wires going to each speaker (if using 4 channel mode) or isolate the wires going just to the rear if you are using 2 channel mode. you have to strip a small piece of the insulation off each speaker wire, and run it into the amps high level input harness. if you dont have the high level input harness, you can get a 2 channel high level to rca adapter for around $20. basically, you are tapping into the signal to the stock speakers to feed music to the amp. make sure you get all your positives and negatives correct. brighter wires are usually positive; however you may be faced with sa speaker which uses a grey wire, and another grey wire- the second with a black line. you will have to, again, turn to internet research to determine which is positive and negative, if the colors are not obvious.

Dec 30, 2016 | Boss Car Audio & Video

1 Answer

Master reset for kenwood kvt-614


The reset button is just to the left of the volume control. See the picture in the downloadable manual at... http://www.manualslib.com/manual/86153/Kenwood-Kvt-614.html

Jul 02, 2014 | Car Audio & Video

1 Answer

How do I reset a Kenwood KDC-24BU flashing "PROTECT"?


Take of your positive battery cable. This should erase all your memory, since the car has no more power.

Jun 01, 2014 | Car Audio & Video

1 Answer

How do I reset a Kenwood KDC-24BU that is flashing "PROTECT"?


Replace the blown/shorted amplifier output Mosfets that are causing it, and it will then be happy to reset itself :)

Jun 01, 2014 | Car Audio & Video

3 Answers

Lightning audio b150.2 as soon as +12 is hooked up blows 25 amp fuse and the c2 1000uf/35v capacitors blow???????


Disconnect all speaker connections and rca cables. Leave power, ground and remote wires intact. Try turning on again. If you still have a protection light your amp is faulty. Hopefully you have warranty. Double check all connections .A thumbs up would be greatly appreciated if this answer is helpful to you.

Aug 25, 2009 | Lightning Audio PC2 Capacitor Car Audio...

2 Answers

RCA CABLES


RCA cables are the best way to get the audio from your head unit to the amp. If your head unit doesn't have RCA outputs, you might be able to use the speaker outputs of the head unit to connect to the "high power" or "high level" inputs of the amp, if the amp has such inputs (check your manual).

Mar 23, 2008 | Lightning Audio LA1.300.2 Car Audio...

Not finding what you are looking for?
Kenwood KVT-719DVD 7 in. Car Monitor Logo

Related Topics:

689 people viewed this question

Ask a Question

Usually answered in minutes!

Top Kenwood Car Audio & Video Experts

xxxxxx xxx

Level 3 Expert

4766 Answers

Pablo Gonzalez

Level 3 Expert

733 Answers

yadayada
yadayada

Level 3 Expert

67911 Answers

Are you a Kenwood Car Audio and Video Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...