Question about Technics SUV500 2-Channel Amplifier

2 Answers

No Sound When Records are recorded to Computer via the Microphone

Hi : I have a Technics intergrated Amplifier I play my old records on a Technics Turntable and input sound into my computer via the microphone port. Everything seem to be working but I have no sound when I go to Playback . If I put apre recoreded CD in Computer speakers work. Computer sounds are also normal. What have I done wrong. What output jacks do I use off the Amplifier . I have Tape 1 Record Out Playback and Tape 2 record Out / Playback . Those are the only output jacks I see.

Posted by on

  • coolhandsbob Dec 23, 2008

    I think my main problem might be my on board sound card , so I am going to upgrade to a regular sound card like Sound Blaster . Wikll likely get better overall preformance out of it anyway. Thanks For Your Help Bob

×

2 Answers

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Sergeant:

    An expert that has over 500 points.

  • Expert
  • 485 Answers

The mic input is for a low level source. You would likely overload it if you used it that way.

Use the "line in" instead.

Posted on May 15, 2016

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    New Friend:

    An expert that has 1 follower.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 59 Answers

Use tape1 record out to the Line in jack on your computer. you should then be able to record to .wav, .mp3s etc. with an audio program like Nero.

Posted on Dec 22, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Creek amplifier


It seems that you have a low Hz feedback loop between the speakers and the tonearm/stylus.
Usually it's only a visual effect and very little can be heard.
In the old times there was a "subsonic" filter in the phonostage part of the amps to cut this out.
You could try a different placement of the turntable as this phenomenon is induced by airborne vibrations and a different placement could ameliorate this interaction...

Jun 05, 2014 | Creek Amplifiers & Preamps

1 Answer

How do I connect my CD Player, Tape Deck and Tuner to the SU 300 Technics Amplifier


hi,
For connecting these to your amplifier you need 4 Stereo RCA Cable.
1.Connection for cd:
Take one of the RCA cable connect the one end (red/white) jack to the line out of your cd and connect the other end (red/white) to the CD input of Your amplifier.
2. Connecting the tunner:
Take one of the RCA cable and connect the one end (red/white) jack to the line output of you Tuner and connect the other end (red/white) to the TUNER input of your amplifier.
3. Connectiong the tape deck:
Now you have two RCA cable. Take one of the RCA cable and connect the one end (red/white) jacks to the PLAY out of the Tape deck and connect the other end (red/white) to the TAPE 1 play input of your amplifier.
Now connect the last RCA cable. Connect the one end (red/white) jack to the record input of the TAPE deck And connect the other end (red/white) to the TAPE 1 Record input of your amplifier.(this connection will help you to record to tape from cd or tuner. if you are not interested in recording then you can avoid this connection.)

Now you can select these three items from the frond plannel control switch of the amplifier.
ok

Jul 28, 2011 | NAD 218THX 2-Channel Amplifier

1 Answer

How must I connect the amplifyer V500 with my computer for recording from a tape player?


I assume you want to record from tape to computer and monitor the recordings later.
Simple three steps.
1) Connect the tape deck line out ( or labeled PLAY ) to any one of the inputs like Aux / Tuner using an 2RCA connector.
2) Connect Rec out from the SUV' to line input of your PC ( blue socket ) sound card.
3) To monitor your PC sound after recording on to Hard Disc , connect a cable between the PC sound out ( green socket ) and the the SUV Tape monitor IN ( sometimes labeled PLAY ) Now comes the tricky partbobhifi_30.jpg.When you want to record on to your PC put the source switch on the SUV to where you have connected the Tape deck ( Aux / Tuner ). On the SUV keep the Tape Monitor switch to source ( released position ). After having done the recording to monitor and hear the Hard Disk playback turn on the Tape Monitor switch ( dipress it ). The pressing of the Tape switch on the SUV lets you toggle between the source and recording - In your case Tape deck and PC

Mar 31, 2011 | Technics SUV500 2-Channel Amplifier

2 Answers

My technics intergrated amplifier says over load


overload is protection from very big signal input-or high current output.
1-keep your input signal between -10db-----to 0db.
2-confirm that amplifier power is greater than total power of loudspeakers by 20%(if loudspeaker total power is 8 watt-amp watt must be 10 watt at least.

Nov 30, 2009 | Technics SUV500 2-Channel Amplifier

1 Answer

Technics su-Z750 Intergrated Amplifier stays in Standby


HI...
This happens when one or more components in the power amplifier section has failed.

The protect circuit keeps large DC voltages off the speakers.

The only thing you can check for before finding a tech is that the speakers are firmly connected at both ends. If they are ok, you need a tech

PLease rate my help if this helps

Nov 05, 2009 | Technics Amplifiers & Preamps

4 Answers

Connecting speakers to amplifier for complete beginner


You will have to use two cables for the same. So you need to buy two more cables.

Thanks

Nov 01, 2008 | Amplifiers & Preamps

1 Answer

Arcam alpha 7 amplifier goes back into standby when volume is turned up


Hi,
Can you, or can someone you know, check for DC voltage on the speaker terminals when the amp is on, but not playing? Ideally, the meter should read 0mV with no signal, and certainly less than +/- 10mV. Anything over +/- 30mV is worth having checked out, especially if it changes as you turn the volume knob with no signal applied.

Aug 29, 2008 | Amplifiers & Preamps

2 Answers

Technics SUV500 Amplifier


check volume balance between right and left-then change inter connection between sound source and amplifier with new cabel(i prefer gold plated type connectors)(see radio shack).
after that if the problem excit your fault in output transistors or output stereo ic depend on circuit design.

Feb 17, 2008 | Technics SUV500 2-Channel Amplifier

1 Answer

Purchased technics sl-bd20d what else do i need just to play records ?


well the mixer is optimal way if you are planning to buy another one sometime but if you are to have only one then you need a corrector which changes the signal (preamp)
just ask for a corrector and say your problem in any tech-shop they will help you..

Dec 18, 2007 | Amplifiers & Preamps

Not finding what you are looking for?
Technics SUV500 2-Channel Amplifier Logo

Related Topics:

318 people viewed this question

Ask a Question

Usually answered in minutes!

Top Technics Amplifiers & Preamps Experts

 Grubhead
Grubhead

Level 3 Expert

4590 Answers

Donald DCruz
Donald DCruz

Level 3 Expert

17129 Answers

Electro Med Services...
Electro Med Services...

Level 3 Expert

5653 Answers

Are you a Technics Amplifier and Preamp Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...