- If you need clarification, ask it in the comment box above.
- Better answers use proper spelling and grammar.
- Provide details, support with references or personal experience.
Tell us some more! Your answer needs to include more details to help people.You can't post answers that contain an email address.Please enter a valid email address.The email address entered is already associated to an account.Login to postPlease use English characters only.
Tip: The max point reward for answering a question is 15.
Enter your model number and a list of major sub-components will come up.
Since it isn't agitating (I assume not at all rather than just the top part of the agitator. If just the top part
isn't turning then the easiest solution is replacing the 4 "agitator dogs" ) the solution points to a
couple of places.
1. The motor coupler
#13 on diagram Coupling, motor and isolation Number:3364003Substitution:285753A $18.50 In stock may be broken. This piece is a fail safe between the motor and transmission. and basically transmits power to the transmission.
If it spins and drains OK, and if you can hear the motor turning, the problem points to the transmission.
Inside the transmission are a number of gears, springs, and plastic cams and levers. Over time one of
them may have either broken or worn out.
There is a Whirlpool site with a parts list for their "commercial washer" which is essentially the same as
for your washer. On it is a list of all of the components and parts for the washer.
By paging down to and following the diagram of the transmission you should be able to determine
Which electronic control module did you replace ? The washer pump is controlled by the front control module . Located in the integrated power module . Fancy name for the under hood fuse / relay box.
Do you know what a wiring diagram is ? How to read one ? Here is a web site for free wiring diagrams . http://www.bbbind.com/free_tsb.html Enter vehicle info . year ,make ,model an the engine size . Under system click on body & accessories , then under subsystem click on wiper/washer .Then click search an a link will pop up . Click on it , second diagram you'll see you front washer pump an the module that controls it .There could be a short to ground on the brown wire , or a problem inside the fuse box . Do you know how to do automotive electrical testing ? Automotive Electrical Fault Finding How to Use Multimeter to Troubleshoot Common Problems The Trainer 18 Electrical Testing Tips
Sounds like the motor may be bad but the only way to know for sure is to do some electrical testing with a volt/ohm meter and the wiring diagram located within the appliance. If possible use the meter and the wiring diagram to check input/output voltages looking for discrepancies between the diagram and the actual meter readings.
The F1 fault is indicating a problem with the main machine control board assembly. It may be going bad but the only way to know for sure is to do some electrical testing with a volt/ohm meter and the wiring diagram located within the appliance. If possible use the meter and the wiring diagram to check input/output voltages looking for discrepancies between the diagram and the actual meter readings.
washer is 2 years old and this is 1/2 the cost I paid for it new. My
review of this product after 35 years of technical experience; GE
products (Hotpoint)aren't worth buying any longer.
The problem is the Motor. There is an electronic PC Board attached to the top of the motor and under the drip protector, which protects the PC Board. On this board, there is a green flashing light which displays trouble codes by flashing. Unplug the washer, remove the 3 screws from behind the control panel. Slowly pull the control panel toward you and slide it to the right to release. Inside the washer, there is a diagram with the trouble codes printed in the lower right hand corner. Everything else is self explained. Flashes indicate the problem and the solution is all written. Since I have the same problem and a technician, this is a defective product GE has discontinued and re-manufactured. After phoning GE the motor #
WH20X10051 cost $252.25 to ship to my location.
Hello, Step 1 go to http://www.frigidare.com Step 2 click on CUSTOMER SERVICE on top of page Step 3 go to PRODUCT MANUALS and click on DOWNLOADS Step 4 type in MODEL NUMBER and click on search Step 5 your error code information is in the TECH DATA file there you can perform a full system check PLEASE READ ALL WARNINGS POSTED
Step 6 Also check INSTALLATION INSTRUCTIONS for part installation or (WIRING DIAGRAM if you are qualified with electrical experience NOT FOR NOVICE) Step 7 save all PDF files to a new folder name it FRIGIDARE for easy availbility for printing or viewing. Thank you and good luck.