Question about Washing Machines

1 Answer

My hotpoint washing machine doesn't stop filling up with water

It keeps filling up through each of the cycles. what is wrong

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Genius:

    An expert who has answered 1,000 questions.

  • Master
  • 1,028 Answers

Remove front cover by sliding putty knife along top edge and pressing down on clips pull front off ck small hose attached to tub on left side look for a dark build up in tube pull off and clean..blockage will cause water level switch not to sense full tub of water..if tub just never fill ck drain hose for correct height from floor and loose fit in standpipe

Posted on Dec 22, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My idesit IWB5113 just keeps filling after starting the wash cycle, normal it inject some water then starts washing, my machine just keeps filling and doesn't seem to start the wash cycle, please help


It is possible that the water level sensor has failed and so does not detect to stop the inlet valve from filling.You can remove and check this level sensor normally it can be a damaged diaphragm and replace the same so that the program proceeds to the next stage to start the machinetips to see working of the machine;http://www.espares.co.uk/advice/washing-machines/a/7/1392/how-a-washing-machine-works.html

Mar 14, 2012 | Washing Machines

1 Answer

Hotpoint aquarius drum fills to top with water


will it stop when you stop the cycle? if so your pressure switch could be the problem however if that does not stop the water you intake water valve is most likley the problem

Feb 06, 2010 | Hotpoint Aquarius WMA42 Front Load Washer

2 Answers

My Hotpoint Ultima keeps displaying an F10 fault and doesnt spin correctly. However, if I then switch it to a rinse and spin cycle it seems to spin OK.


F10 meanswater level pressure switch not sensing correctly, there could be a blockage in the switch hose or chamber, or the switch could be faulty.

Jan 17, 2010 | Hotpoint Ultima WF860 Front Load Washer

1 Answer

Keeps filling during wash cycle


If the machine des not stop filling and cycle hang in position, then it is a faulty water level switch.

If the machine does not stop filling , and the cycle goes on, then test that the inlet valve is not stuck in open position, if the inlet valve is OK, replace the timer control assembly.

Mar 07, 2009 | Hotpoint Ultima WD72 Front Load...

1 Answer

Hotpoint wma22 fills with water but won't wash or spin


Suspect motor brushes need replacing.
Simple task accessed by removing the top of the washer and releasing the clips holding the brushes into the motor - clip on back of brush - to remove the brush assembly.
Replace complete brush assembly.

Feb 16, 2009 | Hotpoint First Edition WMA22 Front Load...

1 Answer

HOTPOINT WASHER DRYER WD440G


That means that the machine detected a problem at a certain point of the cycle and stopped.

If the machine stops when filling check the inlet valve and the water supply.

If it stops because ofervilling check the water level switch.

If it stops when the cycle is hot water only , then check the heating element.

If it stops when draining, then inspect drain filter, drain pump , and drain hose. You access the drain hose removing a panel at the front side of the machine.

If it stops when motor is supposed to spin faster (rinse) then it is motor control unit or motor coupler.

If it is none of the above, then it is a defective control board.


Feb 16, 2009 | Hotpoint Ariston WD440G Front Load...

1 Answer

Ashing machine not emptying


check the drain pipe is not blocked, to empty the machine manualy get a bowl on the floor and lower the drain pipe into it and fill to stop water flow lift pipe up in air and lower to start draining again when empty if pipe not blocked i would suggest a new pump located under the drum and easy to fit

Feb 05, 2009 | Hotpoint WMA46 Front Load Washer

1 Answer

Hotpoint topload washing machine won't water won't stop running.


washer top load will not stop filling even when turned off

Dec 01, 2008 | Hotpoint VBSR3100D Top Load Washer

Not finding what you are looking for?
Washing Machines Logo

Related Topics:

765 people viewed this question

Ask a Question

Usually answered in minutes!

Top Washing Machines Experts

Dan Webster
Dan Webster

Level 3 Expert

8147 Answers

Richard Roth
Richard Roth

Level 3 Expert

9472 Answers

Donald DCruz
Donald DCruz

Level 3 Expert

17129 Answers

Are you a Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...