Question about KitchenAid KGST307 Gas Kitchen Range

1 Answer

Oven and clock not working

'buttons' on panel not working...therefore oven not working light comes on when door time box is the following... F2:E3 thank you

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points


    An expert that gotĀ 5 achievements.


    An expert whose answer gotĀ voted for 20 times.


    An expert who has written 20 answers of more than 400 characters.

  • Expert
  • 125 Answers
Re: oven and clock not working

This error message is indicating "Keypad Spill". Now this can mean pulling it out and cleaning it, or it is faulty. Use a small amount of contact cleaner spray, be most carefull to refit the ribbon cable correctly, and don't forget to unplug it before you do anything.

Posted on Aug 11, 2007

Add Your Answer

0 characters

Uploading: 0%


Complete. Click "Add" to insert your video. Add


3 Points

Related Questions:

1 Answer

Door locked

Your door lock mechanism failed. Needs to be replaced

Apr 11, 2013 | Thermador RDFS30 Dual Fuel (Electric and...

1 Answer

Inglis Niagara oven not working since power outage

try pushing cook and hold button once until lock comes on, then push cook and hold button again. The lock should be removed.

Aug 13, 2009 | Maytag MER6772 Gemini Electric Kitchen...

2 Answers

Maytag Oven Door is locked

Suggestion from =>

The first step I would recommend you to do is to turn the circuitbreaker on, then set up the oven clock. Start the self clean for anyamount of time, wait about 30 seconds and push the cancel button. Mostof the time it helps to eliminate the problem.

I've read other places that turning the fan off will unlock the oven.

Dec 31, 2008 | Maytag MGR5751AD Gas Kitchen Range

2 Answers

Kenmore Oven Door Lock Stuck Out

We had this same problem. We found that pushing the censor button/switch on the upper left rim of the oven's inside moved the lock and made it capable to unlock, or purchase a pizza pizzaz.

Oct 05, 2008 | Kenmore 79012 / 79014 / 79019 Gas Kitchen...

4 Answers


Not too common at all.Tough call ,you really can't hold the tenant at fault,replace the over priced clock and inform the tenant that the next one THEY will have to pay for.

Jun 02, 2008 | Kitchen Ranges

6 Answers

F9 Code after power outage - Model JGR8855ADS

Try unplugging the oven from the electrical power. May release the lock, which is held in place by a tiny micro switch. If not and while the electric is still off or the oven is unplugged, use a bright light flashlight to look through the slot where the lock is in the oven, not in the door.

You may be able to use a thin blade screwdriver to move the lock to the release position. Check the angle of the lever. A slightly bent lever handle also can cause this type of condition.

If all else fails, remove the access panel on the front of the oven to access the locking device and release it. May have to disconnect the wires to the lock which will allow door to function but not during any self cleaning modes.

Fault Code Interpretation Components To Check
F-1 Communication error between touch pad and ERC (clock)
Replace the touch pad or clock.
F-2 Oven temperature sensed by electronic control Replace the clock/relay board
F-3 Open oven sensor or harness. Replace the oven sensor
F-4 Shorted oven sensor or harness Replace the oven sensor
F-5 Power to element relay disabled in cook mode Replace the clock/relay board
F-7 Shorted touch pad key sensed for 32 secs. Replace the touch pad/control panel
F-8 Shorted meat probe Replace the probe jack.
F-9 Door lock safety circuit on ERC sensed Replace the door latch assembly
F-C or F-0 Communication error between boards Replace the relay board

Maytag-Maycop-Magic Chef-Jennair-Admiral: Oven Fault Codes:
F0 Function key shorted or stuck button Clean and unstick button or replace Touch Pad or Clock
F1 Defective Touch Pad or Membrane Replace Touch Pad or Membrane
F2 Oven over heat defective Relay Board or (if present) or defective Sensor
F3 Oven Sensor Open Replace Sensor
F4 Shorted wire or Sensor locate short and correct it or replace Sensor
F5 Hardware, safety circuits disagree Replace Clock
F6 Missing AC (power) signal Check for proper voltage (plug, breaker, etc.)
F7 Function key shorted or stuck button Clean and unstick button or replace Touch Pad or Clock
F8 A/D Warning Replace Clock
F9 Door Lock Warning Check door lock circuit or Replace Clock

Mar 09, 2008 | Jenn-Air JGR8875QDS Gas Kitchen Range

1 Answer

The touch pad panel on stove is blank

on the ge range, you need an ERC its the main control for the oven. yes its costly. comes in a kit with a new wire harness

Nov 16, 2007 | GE Profile JGSP48 Gas Kitchen Range

4 Answers

Oven not heating after self-cleaning cycle.

That did it for me too. You saved me a $200 service call!

Nov 05, 2007 | Dacor Epicure ERD30 Dual Fuel (Electric...

1 Answer

Oven controller not functioning

9. The time of day does not display on my electronic oven control. If I push the CLOCK pad on the control panel the time will display for a few seconds and then it goes blank again.
  • On many ranges with electronic controls the time of day display can by turned off or on by holding the CLOCK keypad down for 15 seconds.
    Push and hold the CLOCK keypad. The time will appear for a few seconds, and then disappear and finally it will reappear and beep. Release the keypad and the time should continue to display. Follow this same procedure to turn the time display off.

Nov 04, 2007 | Frigidaire FEF336BC Electric Kitchen Range

Not finding what you are looking for?
KitchenAid KGST307 Gas Kitchen Range Logo

134 people viewed this question

Ask a Question

Usually answered in minutes!

Top KitchenAid Kitchen Ranges Experts


Level 3 Expert

2963 Answers

Cindy Wells

Level 3 Expert

4722 Answers


Level 3 Expert

57192 Answers

Are you a KitchenAid Kitchen Range Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides