Manual for Sabrent USB 2.0 to IDE/SATA Cable for 2.5-Inch/ 3.5-Inch / 5.25-Inch Drive with Power AdapterWhat's your problem?

Hi
The easiest way that I have found is to get a kit that allows you to power the drive from a separate wall socket and connect a data cable from the drive to a USB socket on the computer. Such a kit usually consists of four components:
A mains lead - wall socket to black box transformer
The black box transformer - has outlet 4 pin molar for IDE drives
A USB cable ending in unit for connecting to an IDE drive or SATA cable
A SATA cable for connecting to the SATA drive (your Barracuda 1Tb in this case)
The components can be seen on this Ebay site:-
USB 2 0 TO SATA IDE Cable for HDD with Power Converter Adapter UK
The one thing missing from this set up is a power conversion cable converting the molar 4 pin power connector to a SATA power connector. These can be a molar plug to go into the lead from the black box and either a single SATA power plug, or a double SATA power connector as shown here :
Molex to 2x SATA Power Dual Power Adaptor Splitter Cable Lead Hdd Cd DVD...
This option is inexpensive and offers great flexibility in the type of drives that can be connected to a USB port, 2.5 or 3.5 inch, SATA or IDE.
In your particular case you may be able to get a dock that connects to a power supply and a USB port, with an opening in the top to take a SATA drive. These tend to be more expensive and only suitable for SATA drives not IDE.
Hope this is helpful, if so would you please register that with Fixya
Cheers

hi
any case 3.5 usb 2.0 or usb 3.0 can buy

USB 2.0 To SATA IDE 3.5 2.5 Hard Drive with an Adapter Cable http://www.youtube.com/watch?v=iE8t5IGr0e4
http://www.ebay.com.au/itm/USB-2-0-to-SATA-IDE-2-5-3-5-Hard-Drive-HDD-Adapter-/330612048804?pt=AU_Laptop_Accessories&hash=item4cfa0383a4
USB 2.0 to SATA IDE 2.5 3.5 Hard Drive HDD Adapter Kit

AU $8.09 free postage worldwide
You would have to remove the hard drive and use a usb sata ide kit
you will then have to connect it to your computer using a usb port

USB 2.0 To SATA IDE 3.5 2.5 Hard Drive with an Adapter Cable http://www.youtube.com/watch?v=iE8t5IGr0e4
http://www.ebay.com.au/itm/USB-2-0-to-SATA-IDE-2-5-3-5-Hard-Drive-HDD-Adapter-/330612048804?pt=AU_Laptop_Accessories&hash=item4cfa0383a4
USB 2.0 to SATA IDE 2.5 3.5 Hard Drive HDD Adapter Kit

AU $8.10 free postage worldwide
You would have to remove the hard drive and use a usb sata ide kit
you will then have to connect it to your computer using a usb port

Schematic

The eMachines T6532 uses an MSI MS-7207 motherboard.
Also known as the KN8GM2-L,

http://www.msi.com/product/mb/K8NGM2-FID--IL--L.html

[ http://www.newegg.com/product/product.aspx?Item=N82E16813130041 ]

The MSI motherboard has provisions for using, EITHER an
IDE (PATA) harddrive, or a SATA harddrive. (Or more than one)

Two different technologies.
I will explain both, using an IDE (PATA) harddrive,
OR;
Using a SATA harddrive;

On the MSI Support page above, click on the Download tab.
(Overview / Specifications / Download / Support / etc)

In the drop down list click on - Manual

Language > English > 7.1MB > E7207v2.0.zip
Click on the blue E7207v2.0.zip

On the next page click on the country name nearest yours.
A small window will come up -
Opening E7207v2.0.zip

Make SURE there is a Green dot in the small circle, to the left of Save File.
IF not; Left-click in the small circle to the left of Save File.
Now go below in the small window, and click on OK

A small download window will come up. Allow the file to download ALL the way, then DOUBLE-click right on it.

In the next small window go to the far left, and click on -
Extract all files.

At the bottom of the next 3 small windows, click on -
Next, Next, and Finish.

In the last small window DOUBLE-click right on the file name.
(7207v2.0(G52-M7207X5) next to the red Adobe PDF icon)

There is the Motherboard Manual

The MS-7207 has two IDE slots;

IDE 1, which is Yellow in color, and close to the outside edge of the motherboard.
Should have IDE 1 silkscreened on the motherboard, below it.

IDE 2 is Yellow in color also, and right next to IDE 1.

(IDE 2 is in-between IDE 1 and the Ram Memory slots.
The Purple, Slot 4, ram memory slot to be specific. {DIMM 4 )

IDE 1 is used for an IDE harddrive.
IDE 2 is used for an IDE optical drive.

TWO IDE harddrives can be put on a single flat ribbon IDE cable,

http://en.wikipedia.org/wiki/File:ATA_cables.jpg

NOTE that there are two styles of IDE flat ribbon cables;
40-wire cable,
OR;
80-wire cable.

BOTH have 40 socket holes in their connectors.
(ONLY 39 are used, so one hole May, or May Not be blocked off)

How to connect to a 40-wire IDE cable, or an 80-wire IDE cable,

http://www.mikeshardware.com/howtos/howto_connect_ide_hd.html

An IDE cable usually has a Locating Lug on it's connectors, in the middle of the connector; and on one side,

http://en.wikipedia.org/wiki/File:PATA-cable.jpg

Here you see the Locating Lug as being two separate 'ridges'.
Some styles the Locating Lug is single block.

The motherboard connector has a matching Cutout on one side.
The Locating Lug lines up with the cutout when installing the cable.

The Harddrive, and optical drive (CD/DVD drive), will have a cutout on their circuit boards.

There are 40-pins. (Only 39 are used if so)
One of them is the number 1 pin.
The IDE cables are plugged into the motherboard, with number 1 pin lining up with number 1 wire, in the IDE cable.

Same when the IDE cable is plugged into a Harddrive, or optical drive.

IF, there is no Locating Lug on the IDE cable;
Look for the faint RED stripe, on the side of the IDE cable.
Number 1 wire is on the same side, as the faint Red stripe.

When plugging into a motherboard, Number 1 pin is on the Bottom.
The faint red stripe on the cable, goes towards the BOTTOM of the motherboard.
(Motherboard installed in computer case)

When plugging into a Harddrive, or optical drive; the faint red stripe ALWAYS goes toward the power cable,

http://www.playtool.com/pages/psuconnectors/connectors.html#peripheral

This shows you the Back of an IDE (PATA) harddrive, and the power cable used for it.
If -> No Locating Lug on IDE cable, the faint Red stripe goes towards the power cable.

This is a 4-pin standard Peripheral power cable.
Note when installing the rounded corners ALWAYS goes UP.

[This power cable is frequently, and erroneously; referred to as a 'Molex' power cable.
Molex was just the first manufacturer of the power cable CONNECTOR. Name STUCK.

Kind of like calling an adjustable open-end wrench, a 'Crescent wrench ]

A SATA power cable is used for a SATA harddrive, or SATA optical drive,

http://www.playtool.com/pages/psuconnectors/connectors.html#sata

There is an L-shape in the SATA power cable's connector.
It matches an L-shape on the Harddrive, or optical drive.

Between a SATA power cable's connector, and a SATA data cable's connector; a SATA power cable connector is the LARGER of the two.
A SATA power cable has 15-contact pins.
A SATA data cable has 7-contact pins.

A SATA power cable's connector may have a LOCK on it.
Usually a Tab, or 'bulb' type affair.
It is pressed down with the thumb when installing, or removing the SATA power cable.

This is a general example of a SATA data cable,

http://en.wikipedia.org/wiki/File:SATA_Data_Cable.jpg

Now you can see the L-shaped opening a little better, that both the SATA data cable have, and the SATA power cable, has.

In the photo the SATA data cable's connector, is a 90 degree bent Elbow.
This style of connector is usually used on the Harddrive, or on the optical drive.

A Straight connector style is usually used for the Motherboard.
However, you can use a SATA data cable, that has a Straight connector on both ends.

Looking at your motherboard, installed in a computer case; there are 2 SATA connectors on the motherboard.

(CAN, be up to FOUR)

I see one motherboard reference where they (2) are Orange in color, (Newegg), and the motherboard manual shows them (2) to be Purple in color.

They are located towards the Bottom/Right corner of the motherboard.
Above the CMOS battery.

The SATA connector that is closest to the Outside edge of the motherboard, is SATA1 (SATA 1)

The Harddrive plugs into SATA 1.

An optical drive that is SATA, will plug into the SATA2 connector.
To the Left of the SATA1 connector.

KNOW THIS;

DOES NOT MATTER, which SATA connector you plug the Harddrive, or optical drive; into.

The beauty of SATA, is that you can plug the Harddrive or optical drive into ANY SATA connector, (On ANY motherboard), and BIOS will find those devices.

BIOS looks FIRST, to see which drive has the Operating System on it. (Windows)
THAT, is the Harddrive.

After finding the drive with the O/S on it, then BIOS will find all the other drives. Removable, or not.

So there you have it. A lot of reading.
You need a power cable, and a data cable to the Harddrive.
Same thing for the optical drive/s.

To have me clarify anything I have stated above, please post in a Comment.

For additional questions please post in a Comment.
Regards,
joecoolvette

Your description has me confused. I'm not clear on which power and data cables you are using. You described pulling one cable from first hard drive and connecting it to your second drive. Extra power connections should have been in a loose wire bundle somewhere in the computer. (Often they are tucked into an unused drive bay.)

The SR1720NX has 2 SATA controllers and two IDE controllers. Thus it can have 2 SATA and 4 IDE devices. The computer sometimes shipped with a SATA hard drive or an IDE hard drive. In all cases, the hard drives must be connected to the data cable (and to the motherboard) and then the power connection from the power supply has to be connected. So there should be 2 cables plugged into each drive. The optical drive is usually an IDE drive for this model, also a master drive.

The IDE power connection is a large 4-pin Molex connector; the SATA power cables are a smaller 5 pin connector. There is also a small 4 pin connector that powers a floppy drive, if present. IDE data cables are a wide 40-pin ribbon cable (sometimes an 80-pin cable for master/slave). The SATA data cable is a 15 pin cable.

First make sure that the jumper on the drive from the A430n is across the two pins in the second position (counting from the side away from the power connection). This is the cable select option. Next make sure that the IDE cable is firmly connected to both drives and the motherboard. (I've sometimes loosened the data cable while connecting the drives.) Finally check that the appropriate power cables are firmly connected to all the drives. Then power up the computer. (With the second drive on the Slave connection, if the device on the Master connection isn't powered up/recognized, then weird things may occur.)

BTW: you should be alert to the power needs for the computer. The original power supply could be overloaded with the extra drive. You might be better off using an external drive enclosure (USB) or a USB/SATA/IDE dongle that leaves the drive out in the open. Connect these with extreme care following the directions for when to connect the power supply. Some enclosures won't work without reformatting the drive - you do not want one of those.

I hope this helps.

Cindy Wells

It depends upon where the hard disk is to be installed, ie. in a desktop computer, in a laptop or in an USB hard drive case.

A 3 1/2 inch hard drives can be a IDE/PATA or a SATA type. Older computers use IDE/PATA hard drives and the maximum size you can install in a desktop depends upon the computer's BIOS.
SATA hard drives are generally used in later model computers and the size of the hard drive is not limited by the BIOS.

A 2 1/2 inch hard drives are used in laptops and are available in IDE/PATA and SATA types. The size and limitations of IDE/PATA hard drives also apply to laptops. The same applies to SATA hard drives.
The choice and size of hard drive depends upon your requirements and how much you want pay.
Don't forget to check BIOS for the maximum IDE/PATA hard drive size you can install in your computer.

In many of these cases, you can replace the internal data cable on the hard drive cases with a separate cable - I did that for two hard drive boxes that I owned, both of their IDE cables somehow "stopped working" after a year or two.

I'd recommend buying something like this to fix it:http://www.amazon.com/iMicro-240149-SATA-Data-Cable/dp/B001O4EPHA/ref=sr_1_1?s=electronics&ie=UTF8&qid=1293046024&sr=1-1

Also, in the future, Sabrent isn't a good company - I spent $35 and got an Ultra converter.
Right now it's down to $25 - and it's a very high quality piece - I strongly recommend it:
http://www.tigerdirect.com/applications/SearchTools/item-details.asp?EdpNo=3276554&CatId=3770

SATA 3.5" 2.5" IDE 3 IN 1 TO USB 2.0 CABLE ADAPTOR KIT

1 external connection kit
1 internal connection kit

The internal connect kit consists of 1 red USB connector cable
and 1 internal white male molex connector to SATA female power connector
( 1 yellow wire , 2 black wires , 1 red wire )

the external connect kit
consists of a 3 pin power adaptor (with a tiny plug to save space) feeding a power supply which powers either IDE thru a Molex connector or SATA through a supplied adaptor. Supplied also are data connectors to link the IDE or SATA hard drive with a USB port. Use this adaptor set to retrieve data from a hard drive when it is not mounted in a computer.

Selah :-)

1) You will do no harm by reversing the connector, but the PC won't "see" the drive at that point (if your drive has an activity LED it will be permanently ON if the cable is reversed) 2) Most times the USB will have enough power to drive the HD all by itself, but if you are going through a hub that may not be the case. In that situation, plug the device directly into a USB port on the PC.