Question about ASUS WIRELESS ROUTER |WL-520G - RT (WL520G)

2 Answers

I cannot connect to the internet but network is working...

I already configured my new asus wireless router and my network is already working but i cannot connect to the internet..

Posted by on

  • 1 more comment 
  • perkino Dec 25, 2008

    I'm having the same problem, the modem works when connected straight to my xp desktop or vista laptop and the router can connect to both devices either by ethernet or wireless but I cannot get the wireless router to connect to the internet... I've tried turning off the routers firewall but that didnt help and i'm not getting any ping response at all. Any ideas what i can do?

  • Anonymous Jan 01, 2009

    the connection always break down, very unstable.....

  • txpinto Jan 21, 2009

    I can set up a network but no sign of Intenet .

×

2 Answers

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Expert
  • 60 Answers

Did you config the router as an access point?

does the internet work when you by pass the router?

Posted on Dec 22, 2008

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

After 2 exchanges, I've determined that the cause of the WAN drops is an update to the router firmware.  When I purchased the product, the firmware level was 2.0.0.8.  Everything works under this level.  When I updated to the newest (3.something w/ the fancy new admin panel), the WAN connection would constantly drop.  Being sneaky and forcing the router to recovery mode to reflash with 2.0.0.8 will NOT solve the issue.

Posted on Feb 10, 2009

2 Suggested Answers

bradhscherer
  • 63 Answers

SOURCE: i cannot connect to the internet but network is working...

what is the wan IP in your modem?
What is your DNS configuration?
Cna you successfully run the following command from a command prompt?
nslookup google.com
Does it resolve the hostname to an ip address?

Posted on May 30, 2009

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My desktop PC is currently connected to the Internet wirelesly without a problem. Also my notebook ASUS N61Jv has connection to the Internet but only by wire. I wish to have access to the internet...


The router's password is a Passphrase or the WEP or WPA orWPA2 encryption key. The Passphrase generates the WEP or WPA or WPA2 encryptionkey and this is in the router's wireless settings. To connect to your wireless router, it needs the router'swireless settings configured ie SSID, WPA or WPA2 encryption key and also thewireless cards in all the laptops and or computers needs to be configured withthese router's wireless settings. Then the laptops and desktop computers cancommunicate with your wireless router.

Mar 11, 2011 | Computers & Internet

1 Answer

How to conect with wireless internet


The Network and Sharing Center in Microsoft* Windows Vista* can be used to set up a secure wireless connection to the Internet.

Note: If an Internet connection is not automatically made by the operating system, you may need to contact your access point (AP), broadband wireless router manufacturer, or Internet Service Provider (ISP).

Set Up a Secure Wireless Connection to the Internet


These steps assume that your network adapter; AP or router; and cable, DSL or another type of modem have already been physically connected and configured. They allow you to create a new connection and configure it accordingly.

Follow these steps to set up a secure wireless connection to the Internet.

Note: If a wireless profile does not exist, you will need to create a secure wireless profile before you can set up a wireless connection to the Internet.

1. Access the Network and Sharing Center.

2. Select Set up a connection or network.

3. Click Connect to the Internet.

cs025389_selectanetwork_configurationnotmatching.jpg

4. Click Next.

5. Select Wireless. At this point, if the network(s) that are listed say that the network settings do not match the network requirements, as shown in Figure 1, create a secure wireless profile and then follow the steps again.

6. Select a network and click Connect. If you are not connected to the Internet, you may need to contact your AP/router manufacturer or ISP.

Access the Network and Sharing Center


To access the Network and Sharing Center, use one of the following methods:
  • Start » Control Panel » Network and Internet » Network and Sharing Center
  • Start » Network » Network and Sharing Center
  • Right-click the network system tray icon (the icon that displays two computer monitors) » Network and Sharing Center


Jan 21, 2011 | Computers & Internet

1 Answer

Can't get my lap top to connect wirelessly to my router. Model # WRT54G2. The laptop says it is reaquiring the network address, but nothing happens.


The Network and Sharing Center in Microsoft* Windows Vista* can be used to set up a secure wireless connection to the Internet.

Note: If an Internet connection is not automatically made by the operating system, you may need to contact your access point (AP), broadband wireless router manufacturer, or Internet Service Provider (ISP).

Set Up a Secure Wireless Connection to the Internet


These steps assume that your network adapter; AP or router; and cable, DSL or another type of modem have already been physically connected and configured. They allow you to create a new connection and configure it accordingly.

Follow these steps to set up a secure wireless connection to the Internet.

Note: If a wireless profile does not exist, you will need to create a secure wireless profile before you can set up a wireless connection to the Internet.

1. Access the Network and Sharing Center.

2. Select Set up a connection or network.

3. Click Connect to the Internet.

cs025389_selectanetwork_configurationnotmatching.jpg

4. Click Next.

5. Select Wireless. At this point, if the network(s) that are listed say that the network settings do not match the network requirements, as shown in Figure 1, create a secure wireless profile and then follow the steps again.

6. Select a network and click Connect. If you are not connected to the Internet, you may need to contact your AP/router manufacturer or ISP.

Access the Network and Sharing Center


To access the Network and Sharing Center, use one of the following methods:
  • Start » Control Panel » Network and Internet » Network and Sharing Center
  • Start » Network » Network and Sharing Center
  • Right-click the network system tray icon (the icon that displays two computer monitors) » Network and Sharing Center

Jan 10, 2011 | Linksys Wireless-G WRT54G Router

1 Answer

Unable to make router wireless


To use a wireless network/connection you need to do.
1. Configure the router's wireless with SSID, WPA encryption etc.
2. Next configure the wireless card in the computer/laptop with the router's wireless settings so it can connect to the wireless router.
Please click on this link for my instructions on how to secure your wireless network, configure the wireless router and configure the wireless card in the computer/laptop :-

http://www.fixya.com/support/r3559128-wireless_router_security

Feb 10, 2010 | 3Com Computers & Internet

1 Answer

Netgear WGR814v2 does not see my ASUS 1005HA-P netbook, but the netbook sees the the Netgear wireless network but cannot connect .


To connect into your own Netgear router, you need to configure the wireless card with your router's wireless configuration settings, eg.the SSID and encryption settings. Check your router manual on how to configure the router or go to the Netgear WEB site to download this info.
To configure the Netgear router for wireless you need to connect a LAN cable from the laptop to the router and run your browser with the configuration IP address. for Netgear type the URL address ;-
http://192.168.0.1
the login = admin PW = password
Then configure the SSID and encryption, record this info so you can configure the wireless card with the same settings.

You can also connect to the Internet by using a LAN cable and plug it into the Netgear router without a wireless connection.

Sep 04, 2009 | NetGear WGR614 Wireless Router

1 Answer

I cannot connect to the internet but network is working...


what is the wan IP in your modem?
What is your DNS configuration?
Cna you successfully run the following command from a command prompt?
nslookup google.com
Does it resolve the hostname to an ip address?

May 30, 2009 | ASUS WIRELESS ROUTER |WL-520G - RT...

1 Answer

Connecting 2 routers (ASUS WL-500W and D-Link DSL-G604T Wireless)


This will give you a "Double NAT" setup. Meaning, Your D-Link router is connected to the external internet address assigned to you by your internet service provider. More than likely this is a DHCP address you do not control. Your D-Link router is then translating the address to the 192.168.1.x network. This is the first NAT translation. You are then connecting the ASUS router to DLINK, causing a second NAT translation. (Internet ADSL --> D-Link WAN Port --> D-Link Lan Port --> ASUS WAN Port --> ASUS Lan Port to computer/server/etc. ) If both of your routers are giving out DHCP addresses, then this is all that is required.

Nov 22, 2008 | ASUS WL-500W Router (WL500W)

1 Answer

Router linksys set help needed


Just first install the wireless card to your computer then when its already properly installed , connect to the wireless network name of your router and when its say connected try the internet that should e working fine already..........

Aug 07, 2008 | D-Link DI 514 Wireless Router (DI-514)

2 Answers

WRT54GX4 Wireless Router Setup Problems


Hi Randy

Reset the router
Use regular way to configure the Router.
In computer side
Go to Start>Connect To>Show all connections
a new window (Network Connections) will open,
Right click on the "Wireless Network Connection"
Click on "View Available Wireless Networks" You will see "linksys" with the highest signal level. Connect it
after connection go to web browser; type 192.168.1.1 and hit enter. It will take you to Linksys setup page which is integrated in the router. after that you can do any settings you want.
Please post here if you need further assistance

Good Luck

Jan 12, 2008 | Linksys WRT54GX4 WIRELESS 802.11G...

1 Answer

WL 520 GC can only acess net in "default" before encrypting


To enable WEP encryption requires configuration changes in two places the router (WL-520G) and for the network adapter on the associated with the computer expecting to use the wireless router. Do you both believe you made the appropriate changes to both devices required? The router and the computer

Another possible issue is either the router or the network adapter do not support WEP meaning the option is not possible at all.

Oct 24, 2007 | ASUS WIRELESS ROUTER |WL-520G - RT...

Not finding what you are looking for?
Computers & Internet Logo

Related Topics:

540 people viewed this question

Ask a Question

Usually answered in minutes!

Top ASUS Computers & Internet Experts

Brian Sullivan
Brian Sullivan

Level 3 Expert

27725 Answers

Les Dickinson
Les Dickinson

Level 3 Expert

18333 Answers

David
David

Level 3 Expert

756 Answers

Are you an ASUS Computer and Internet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...