Question about Hotpoint 24 in. FDW60 Free-standing Dishwasher

1 Answer

Eco and Prewash lights error

I have a Hotpoint DWF50. After switching on and seating a programme, approximatly 2 mins I get flashiing eco and prewash lights. What could te problem be?

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 157 Answers

Pump or heater

Posted on Dec 31, 2008

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

What is cold resistance of heater element? Bosch SGS56E02GB


If the heater element had infinite resistance, it would be defective. Possibly a defective thermostat.

Jul 01, 2015 | Bosch Dishwashers

1 Answer

My problem was eco & prewash lights flashing so I followed instructions on Fix Ya to reset which seemed tomwork machine went through complete sequence but then reverted back to lights flashing aga


Hi, not sure if its relevent but we have a hotpoint aquarius DWF50 machine, light flashed same at times, sometimes push the switches would not operate properly to select a program. Lately the pump for emptying water at the end of a cycle would continue to run even when it was empty for hours until you turned it off.
Before doing anything else, disconnect the mains lead.....
I checked the float sensor for water etc as advised ...nothing dry..then decided to take off the controller board as previously we had a problem with the relay being dry soldered to the circuit board...on the left hand side of the board I found two thin wires, black and black with grey stripe, one was not soldered correctly to the board..dry joint and pulled away as i tugged at it. Resoldered the joint properly, reassembled board and connectors to the door. Fitted screws back etc. That was a week ago...its been fine since.
No idea what the wires were attached to at the other end but they look like low ampage signal type wires perhaps from some sort of sensor...anyway they should have been soldered properly during manufacture...years ago. Hope that helps ofr gives you something more to go on.
Rob

Jan 13, 2013 | Hotpoint 24 in. FDW60 Free-standing...

2 Answers

Lights flashing


temp solution, switch on and off at wall socket with on/off switch in and out, untill only on/off switch is lit, then use wall switch for power on off. worked for me.

Jul 13, 2010 | Hotpoint Aquarius WF000 Front Load Washer

1 Answer

I have a hotpoint aquarius sdw60 with the eco 45 light flashing fast and will not reset I have tried turning off the power I have stripped the pump this was clear. then reinstalled it but it is still same


I have a Hotpoint Aquarius SDW 60 The delay 3hr &12hr lights are flashing at the same time. Machine won't start. If the door is slamed shut. It get stuck on the Fast & Prewash 40 degree cycle. and stays there.

Jul 13, 2009 | Hotpoint 24 in. FDW60 Free-standing...

1 Answer

Hotpoint Aquarius DWF50 Dishwasher, cycle not starting getting flashing ECO/Fast lights, any ideas?


hotpoint dwf50 will not start, the fast wash and prewash buttons are flashing together.

Jul 05, 2008 | Dishwashers

2 Answers

Dwf50 hotpoint aquarius dishwasher


hi, just found this forum after searching the web 4 a solution to my hotpoint DWF50 problem.
I came down this morning to a machine which base tray was full of water and lights 3 ECO & 4 Fast flashing.
Anyway my solution was as i had seen a hotpoint engineer do once before was to press the start/reset button trip the catch, to fool the machine into thinking the door is closed then put in a program, press start, the machine hums slightly but doesnt do anything then after removing the large filter from the tray at the bottom underneath the lower basket insert a length of wire, with a loop on the end (Tip i used a wire coat hanger from the dry cleaners) poke in ythe hole that the dirty water drains from, after a bit of poking about the pump started working and the water drained away. Tip place a hook at the other end of your wire impliment to put your finger in to stop the wire getting caught in the pump mechanisim. After wards u have to hook back the door catch to the normal position, Tip another piece of the coat hanger with a right angled piece at the end will do this. This worked for me, saved me some money esp as D & G insurance ran out 2 weeks ago.....stu

Jun 16, 2008 | Hotpoint 24 in. DWF32P Free-standing...

1 Answer

Washing machine Prewash light flashing.


hi on the model before this one the wma series the flashy pre wash light is a faulty water inlet valve these mashines are allmost identical inside so check that,first check that you have the hot/cold pipes on the right way around hope this helps

May 03, 2008 | Hotpoint Aquarius WF000 Front Load Washer

Not finding what you are looking for?
Hotpoint 24 in. FDW60 Free-standing Dishwasher Logo

Related Topics:

846 people viewed this question

Ask a Question

Usually answered in minutes!

Top Hotpoint Dishwashers Experts

Marvin
Marvin

Level 3 Expert

83662 Answers

Brad Brown

Level 3 Expert

17639 Answers

Jim Goldsmith
Jim Goldsmith

Level 3 Expert

2005 Answers

Are you a Hotpoint Dishwasher Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...