Question about Sony Televison & Video

3 Answers

Sony Bravia KDF-50E2010 LCD Convergence Problem

Hi ,
Hope you help me, I have the above TV and the Green convergence is
out leaving a ghost image about 1/4 inch to the left of the main image.
Not rearly noticeable on TV imaging but on HDMI on PS3 or WII it is
getting annoying. I've been given the remote inputs to get me to a technical
menu system which opens up loads of setting options but don't want to experiment and stuff it completely. Thanks in advance Andy Linney
Chesterfield England

Posted by on

Ad

3 Answers

  • Level 1:

    An expert who has achieved level 1.

    Governor:

    An expert whose answer got voted for 20 times.

    Corporal:

    An expert that has over 10 points.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 3 Answers

Well this is the fix for the usual Ghosting problem....

To bring up the "service" menu, put the TV in standby mode, then press in sequence :

Onscreen Display ( the little screen with the i+ in it )
5 ( channel number 5 )
Volume Up ( upper end of volume button )
Analogue ( middle top button )

The TV should switch on and when it's warmed up, you should see a screen with lots of big green lettering on it.

Press the "menu" button ( middle bottom )

Use the direction dial to move down to "LCD Drivers" and press right on the dial to enter this menu.

Move down to "S H Pos Reg R". It should be "10", change it to "11". ( Left/Right to adjust )
Move down to "S H Pos Reg G". It should be "10", change it to "11".
Move down to "SHPos Reg B". It should be "10", change it to "11".

Press the menu bottom to drop out of the menus, and the standy button to drop to standby. Switch back on, and hopefully your ghosting will be gone hope this works davy mac

Posted on Mar 16, 2009

  • gk45 Sep 14, 2010

    legend!!!

  • knowleybyrne Feb 09, 2011

    u are a life saver thank u so much, honestly thank u so much :):):)

×

Ad
  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

I have the above tv and it has recently crashed.. there are four lights placed on the front right hand corner of the television. the second light is stayin on constant but the third light is flashing..the television will not turn on could you please help me solve this problem

Posted on Jul 26, 2010

Ad
  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

My tv light goes green for a second then flashes red please help

Posted on Mar 20, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Lower half of the screen has a digital ghost that is


Tv have a convergence problems,it dead.Tv convergence board is dead.Require changing the 2 STK convergence ICS and some or all it resistors.To solved the tv convergence problems.Tries Websites like Tvrepairworld.com,Tvrepairkits.com to buy a convergencce kit.To replaced those convergence parts on the board.

Jul 28, 2010 | Samsung HL-S5679W 56" HDTV

2 Answers

65" rear pro. Convergence IC Repair


This is a common problem. Its called a convergence failure.

Problem #1) Convergence

Symptoms:

  • Screen Looks 3D
  • Colors wont align
  • Video may look distorted
Problem #2 CRT Fluid has clouded over. Symtoms
  • Dull looking video
  • White looking video
  • Halos around objects
  • Red/Orange looking video

You can see some examples and find a fix here...

bb0cf99.pnghttp://www.fixya.com/support/r2861467-solution_video_looking_whiteish_dull

Feb 18, 2010 | Mitsubishi WS-65809 65" Rear Projection...

2 Answers

Double Image Red and Green


Here are some of the most common symptoms and example photos of a convergence problem

  • Screen looks 3D
  • Colors don't line up
  • One or more colors can't be adjusted when using the convergence menu.
  • Screen is bowed or warped.
701cb04.jpg
77ea520.jpg
f0900cb.jpg

Here is a quick test....

Using your original remote go-to the tv settings then goto the convergence section.

Try to adjust the red and then the blue convergence.



You should be able to move them up, down, left, and right.

If you can't move them in all directions your convergence chips are bad and should be replaced. This is a common problem.


2c07611.pngSolution


You need to replace the convergence chips and convergence resistors. Check the site www.TvRepairKits.com. They have put together a kits for most models. If you don't see a kit for your set send them a quick email and they will put one together for you. Their kits includes photo instruction guides, original Sanyo STK chips, convergence resistors, pico fuses, etc.

Feb 08, 2009 | Sony KP-46WT510 46" Rear Projection HDTV

1 Answer

Watching TV and top 1/3 screen ghosted by colors


on this type of tv each gun is controled by hor.and ver. chip together. it is on the board that controls the convergence of the tv. some manufactors have recalls on problems like this. i dont know if this one does but it may. you can check with mitsub. i do know that this part is about 250.00

Jan 02, 2009 | Mitsubishi WS-55511 55" Rear Projection...

2 Answers

Shadowing


GOOD DAY ND GOOD LUCK;

TRY THIS, IT WILL CORRECT CONCERN:

50V500 ONLY
GHOST: May be described as "Out of Convergence" but ghost is still attached to main image.
CONDITION:
A "ghost image" appearing to the left or right of images in the picture. Can be varying shades of a primary color (red, green, or blue) as well as gray. Can easily be seen in the 4 x 3 mode, at the edges of the picture.
CORRECTION:

To correct the problem, please do as follows:
  1. Access I2C Menu. (See page 57 of the Service Manual).
  1. To enter the I2C Service Menu, with power off, (on the front control panel) press and hold the INPUT button. Then press the POWER button for two seconds. The following Service Menu will appear.
03b_ghost_image01.gif Figure 1
  1. BEFORE CONTINUING: CONFIRM THAT THE R, G and B DRIVE ARE SET AT 40.
  • Be sure to press SELECT after each change to SAVE the new Data.


  1. Using the Remote Control joy stick, scroll down to next page (see Figure 2) until LCD ADJUST is highlighted.
03b_ghost_image02.gif Figure 2
  1. Move the joy stick to the right to cursor right once. The next page will appear with the word GHOST highlighted.
  2. Cursor right again, and a white screen will appear with a BLACK SQUARE in the center, as in Figure 3. You will see LCD ADJUST, followed by “SHP” and a number (value).
03b_ghost_image03.gif
Figure 3

  1. If the unit is out of adjustment, you will see a gray ghost on either side of the black square. Move the joystick to the right or to the left until the ghost disappears. The number values will change up or down.
    • If the ghost adjustment is off with a lower value, there will be a ghost to the left of the square.
    • If the ghost adjustment is off with a higher value, there will be a ghost to the right of the square.
  2. Once you get the square to look good without ghosts, press "SELECT" to save any data values that have been changed.
  3. Press the "EXIT" button three times to return to normal picture.
  4. Adjustment is completed
  5. I HOPE THIS WAS HELPFUL, big IRISH.




Jul 26, 2008 | Hitachi 50V500 50 in. HD-Ready LCD...

1 Answer

Old style rear projection TV dolors don't align. See ghost image in Blue several inchs above yellow image. Upper part of screen looks almost normal.


let me know your model number and I will be able to tell you what you need to fix the convergence on your set.

May 15, 2008 | Televison & Video

1 Answer

Double images with red halo outlines


Sounds like your describing convergence ICs. They cost about 10.00 each and you will need to replace both of them. And possibly the resistors that power them total cost under 30 dollars if you do he soldering yourself. Hope this helps.

Feb 10, 2008 | Zenith B50M88W 50" Rear Projection...

1 Answer

Red and green lamps look off center


Intermittant convergence alignment issues are quite common.
Either solder the convergence IC pins or better yet , change out
the IC's with first quality OEM spec or upgrade..............T.

May 07, 2007 | Mitsubishi WT-42315 42" TV

Not finding what you are looking for?
Televison & Video Logo

Related Topics:

2,147 people viewed this question

Ask a Question

Usually answered in minutes!

Top Sony Televison & Video Experts

The Knight
The Knight

Level 3 Expert

75970 Answers

Jerry Greenberg
Jerry Greenberg

Level 3 Expert

1689 Answers

Steve Allison
Steve Allison

Level 3 Expert

5569 Answers

Are you a Sony Televison and Video Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...