Question about Emerson EWV403 VHS VCR

1 Answer

Eject error I get and eject ^ 2 error when I turn on the vcr. It has never had a tape in it. I have a dvd connected to the front ports. When I turn the unit it on, I receive this errror and then it shuts down.

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 10 achievements.


    An expert that got 5 achievements.


    An expert who has answered 1,000 questions.

  • Master
  • 1,070 Answers
Re: eject error

The vcr needs to be unplugged and left for about a day to reset itself.then plugged in back this will adjust the error.

Posted on Apr 04, 2007

Add Your Answer

0 characters

Uploading: 0%


Complete. Click "Add" to insert your video. Add


3 Points

Related Questions:

1 Answer

Vhs tape stuck in vcr

Disconnect power, open VCR cover, free tape if wound around posts, turn eject motor manually (usually located towards the right front) to slowly eject the tape.

Nov 14, 2013 | VCRs

1 Answer

Tape stuck in vcr. when you press the eject button vcr starts to work but shtuts off the power Model number DVR-3034N. I have only taken the front and back covers off. Turned slanted roller untill the...

It sounds like the tape is jammed in the vcr, remove the top cover of the machine this will expose the tape. If the tape is spewed in the mechanical section and around the video head, get a pair of scissors and start cutting the tape and carefully remove all tape particles, when all tape debris has been removed, plug in vcr turn on and eject. If the tape looks good, you may have a loading basket problem, bad idler ***. or broken drive belt. "Lets hope for the best"

Jan 25, 2011 | Emerson VCRs

1 Answer

Samsung v7000 DVD/VCR .....VCR ejects tape when record is pressed

Does this happen with other tapes? If so then the micro switch could be stuck in the open position, try to give it a clean with a blast of air duster first then check the contacts on the switch. If it is happening with just this specific tape the the record tab (although in place) may be "soft" try putting a piece of tape tightly across the tab & try to record.

Aug 13, 2009 | Samsung VCRs

1 Answer

VCR continually tries to eject the tape after it is inserted

If you have cleaned the head with a good head cleaner and you are still having a problem...the belt is probably worn. A good head clean should fix the problem.

Mar 18, 2009 | Zenith VR4127 VCR

1 Answer

Error 2 on Front Panel

I'm not sure if this is a solution, but it cleared up the problem for me. It turned out there was a loose paper label for the cassette that got stuck inside the VCR with the cassette.

I had to take off the top of the VCR by removing the three screws. I then removed the jammed loose paper and then was able to get the cassette out. The flashing number 2 (whatever that means) went away. The machine seems to be working fine now.

Apr 19, 2008 | Philips VR620CAT VCR

1 Answer

Error E3 on Mitsubishi HS-U795

Try this :
If your VCR malfunctions, try the following steps prior to contacting your Mitsubishi Dealer:
1 Check the Trouble Checks below to see if there is a solution to the current problem that you are
2 If the problem is not addressed on the Trouble Checks, the safety circuits in the VCR may be in
operation, thus please try the following: (the clock setting and the timer recording will be deleted.)
1 If possible, press EJECT on the front panel and remove the tape.
2 Press TIMER RESET on the rear panel with a pencil or a ball point pen.
3 If a tape is not loaded, press POWER to turn the power on. If a tape is loaded, wait about 1 minute
until the tape protecting function is completed, then press POWER.
3 You may also try the following procedure if the above steps did not resolve the problem (All settings will
be reset to the default settings.).
1 Press POWER on the front panel continuously for about 8 seconds until the current time display on
the front panel shows "- : - -."
2 If a tape is not loaded, press POWER to turn the power on. If a tape is loaded, the tape protecting
function will work and "99" will appear on the front panel display to begin count down. Wait about 1
minute until it reaches "00" to show the tape protecting function is completed, then press POWER.
If the problem with your VCR persists, contact your Mitsubishi dealer for assistance.

Im looking for error codes.

Mar 10, 2008 | VCRs

1 Answer

Cannot eject VHS tape from Sony SLV-X811

I had a similar problem with a Panasonic VCR. It would not eject the tape and gave an error code. I found that the door does not quite fully open, so that the top of the tape hits the door and cannot eject. If I turn off and then turn on the VCR the error code disappears. Then I press the eject button and simultaneously hold the door fully open with one finger until the tape starts to eject and clears the door.

Feb 29, 2008 | VCRs

3 Answers


Got pets or young ones? This problem just smacks of having something lodged inside. Could also have come from a label coming off inside, too...accordianman

Jan 19, 2008 | Zenith VCS442 VHS VCR

Not finding what you are looking for?
Emerson EWV403 VHS VCR Logo

Related Topics:

97 people viewed this question

Ask a Question

Usually answered in minutes!

Top Emerson VCRs Experts


Level 3 Expert

4518 Answers

Donald DCruz
Donald DCruz

Level 3 Expert

17129 Answers

alexander woolfolk
alexander woolfolk

Level 2 Expert

276 Answers

Are you an Emerson VCR Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides