Question about Philips WACS700 Shelf System

1 Answer

DMM says center not connected when it is connected with cable

I can not get the DMM software to recognize the WAC 700. Says not connected when I know that it is. It has worked before, but I installed software on new computer now having the problem. Tried reinstalling software and in installation it says it is finding the center.

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 11 Answers

Try downloading wach handler from http://www.lucia-mathias.com/wacs/ much superior to philips software

Posted on Jan 25, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Philips wireless music centre model WAC 700/05 will not eject cd or recognise. displays no cd


Philips music centre model 700/05 keep on saying booting please the other one is fine but the main unit which plays CD I have try all the trobleshooting but sill the power can't turn on how can I get the setup CD Rom

Apr 09, 2013 | Philips WACS700 Shelf System

3 Answers

CProblems onnecting Archos 700 after connecting 605 to PC


It is very possible the drivers conflict. You should try uninstalling everything to do with the one you don't want. Then install the drivers/software for the 700. Also what software are you using and what version?
Thanks,
Lee

Sep 21, 2008 | Archos AV700 Digital Media Player

1 Answer

Wac 7000


Hi, I had the same problem when upgrading to windows 8.

My solution was to load the original software on then remove it through programmes and features I believe the windows registry will still hold some of the older registry files needed for it to work. I then went to the Philips site and download the software for a later model I chose the WAC7500 system as some of the newer models require a activation code.

P.S Don't know if this might be part of the solution as well, when the original software was installed I did try to get it to work with the programme compatibility modes before uninstalling.

Jul 17, 2012 | Philips WACS700 Shelf System

1 Answer

My compaq presario f768wm isnt recognizing my cd/dvd rom. my camera quit working and also it says it can't find my audio output device.


Hi,
For that problem, Try first replace that internal DVD-rom drive other good internal DVD-rom drive. if not Also Detected or recognize.
Try this second solution. insert external USB type DVD-ROM. if not recognize also, Your operating system Have internal software device data corrupted. You need to reinstall operating System like windows xp, windows 7 (OS) etc.. to fix data Corrupted of operating system device for hardware software.
Please see sample external DVD-rom USB type.

jimmyverdade_79.jpg

Just let me know if not yet working your Compaq Presario 700 series DVD-rom Drive.
Thanks for using Fixya.



Aug 19, 2011 | Compaq Presario 700 Series DVD-Rom Drive...

1 Answer

Where is the location of crankshaft sensor in VW passat,1995,2,8?


OPERATION
The crankshaft position sensor detects gaps in the sensor ring corresponding to TDC of each cylinder. The sensor uses a permanent magnet, core and coil. The changing gap causes the magnetic field near the sensor to change. This in turn varies the voltage signal to the ECM. The ECM uses the signals for ignition timing and fuel synchronization.
TESTING
Audi A4 2.8L
  1. Disconnect the electrical harness connector.
  2. Switch the DMM to its resistance range and connect it between the CKP sensor connector terminals 1 and 2 , using jumper wires from VW 1594 test kit. The DMM should show approximately 1,000 ohms.
  3. If the specified value is not obtained, replace the crankshaft position sensor.
  4. If the specified value is obtained, connect the DMM between terminal 1 and 3 (GND), then between terminals 2 and 3 (GND). The DMM should show infinite ohms (open).
  5. If the specified value is not obtained, replace the crankshaft position sensor.
  6. If the specified value is obtained, check the wiring for continuity or short between crankshaft position sensor and ECM, using a wiring diagram.
  7. Connect a VAG 1598/19 test box to the ECM harness connector.
  8. Check the CKP sensor shielding for continuity by connecting a DMM between terminal 3 and engine ground (GND). The DMM should show a maximum of 1 ohm.
  9. Check the wiring for continuity between the CKP sensor connector terminal 1 and the test box socket A9 , then between the CKP sensor connector terminal 2 and test box socket A10 . There should be a maximum of 1 ohm.
  10. If the specified values are not obtained, check and eliminate any short or open circuits in the wiring.
  11. If the wiring is OK, replace ECM.

Passat 2.8L
  1. Disconnect the harness connector from the crankshaft position sensor.
  2. Switch the DMM to its ohms range.
  3. Connect the DMM to terminals 1 and 2 of CKP sensor harness, using adaptor leads from VW 1594 adaptor kit.
  4. Resistance between terminals 1 and 2 must be 500-700 ohms.
  5. Connect the DMM to terminals 1 and 2 , then 1 and 3 of the CKP sensor harness, using adaptor leads from VW 1594 adaptor kit.
  6. The resistance must be infinite ohms.

REMOVAL & INSTALLATION
  1. Disconnect the electrical connector from the sensor.
  2. Remove the crankshaft sensor retaining bolt and remove the sensor.
  3. Replace the O-ring and lightly lubricate it with clean engine oil.
Installation is reverse of removal.

---
To remove the sensor:

  • Disconnect the wiring harness.
  • Unbolt the sensor mounting bolt.
If the crankshaft timing sensor or the camshaft reference sensor is removed, follow this procedure when the sensor is replaced:
  • Thoroughly clean the sensor tip and install a new spacer on the sensor tip. New sensors should be supplied with the spacer installed.
fr_24.15.gif

Spacer on crankshaft timing sensor and camshaft position sensor.

  • Install the sensor until the spacer lightly touches the sensor ring, and tighten the sensor mounting bolt 105 in.lb.
---
Look for the sensor on the axis of the crankshaft near either end of the engine.

Good luck on locating this sensor.

Jan 17, 2011 | Volkswagen Passat Cars & Trucks

3 Answers

My adaptor is not recognized in my USB ports I installed the router and it completes all of its connection checks. I am trying to install the adaptor on a remote computer (in the basement) and that...


Here's what you can do since this is a USB wireless adapter, first connect the USB adapter on a different USB port on the computer better if you connect it on the back USB port of the computer tower and check if the computer will recognize it and if its recognize you can already continue with the software installation , but if not you can restart first the computer and check if the adapter will be recognized if still not the next thing to do here just to know if the adapter is good or bad is to connect it on a different computer and just to check if it will be recognized once its connected to a USB port , because a device should be automatically will be recognized by a computer once you connect it so if its still not recognized by a different computer adapter is bad...

Dec 15, 2009 | Computers & Internet

1 Answer

Wacs700


I take it you have use Wac DMM and given it the folder where your music is stored...

All you have to do is rip your CD to that folder and then upload it.

Aug 12, 2008 | Philips WACS700 Shelf System

4 Answers

Problems installing new software


have you checked to make sure the gps is in data transfer mode? menu/active setup/ data transfer

Dec 06, 2007 | Magellan RoadMate 700 GPS Receiver

Not finding what you are looking for?
Philips WACS700 Shelf System Logo

Related Topics:

542 people viewed this question

Ask a Question

Usually answered in minutes!

Top Philips Audio Players & Recorders Experts

Gyula Lacz

Level 3 Expert

486 Answers

 Grubhead
Grubhead

Level 3 Expert

5601 Answers

The Knight
The Knight

Level 3 Expert

75957 Answers

Are you a Philips Audio Player and Recorder Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...