Question about Philips Magnavox 27MS343S 27" TV
I have 2 different models of Magnavox DVD players. 1 is a dvd/vcr combo (Model MDV540VR/17, I think). I just recently purchased Model ZC352MW8. The remotes seem to interfere with each other even though they are in separate rooms.
Is there something I can do to modify the signals for one or the other?
The codes will be the same regardless. Modification of the signals is not possible.
Posted on Dec 17, 2017
A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Posted on Jan 02, 2017
SOURCE: Magnavox combo vcr dvd
What you're describing is common when the center LED has failed / gone out. If you're really good at taking a unit like this apart and putting it back together - and not too bad with a solder stick you could attempt this one yourself... It is a pretty intensive repair but not difficult for a good shop just time consuming. The part isn't too expensive either, just an infared LED... In fact, we've run a bit short on stock once in awhile and bought one of the off the shelf versions from Radio Shack which worked just fine. Good Luck Bill
Posted on Jun 12, 2007
SOURCE: jumbo universal remote
I found that on the back of the 2205 it said that the unit was made by Funai. I looked in the Innovage book and found that the codes for Funai DVD are 231 and 233. 233 worked on mine. Good luck.
Posted on Jan 06, 2008
SOURCE: my tv shuts off
I picked one up in the trash 2004 model 27MDTR20/17. I turn it on and it shuts off. I opened the back and pulled the DVD/VHS board out. I removed a metal cover on the VHS housing (three screws). There was a broken clear plastic rod and one of the gear stop plastic cords (on the left side) was ripped where it attached to the front metal bracket through a hole in the plastic tab. The plastic chord has a piece of white felt like material attached to it. I epoxied the plastic rod back and put a piece of tape over the broken plastic end of the cord. The tape was folded over the edge of the plastic and then wrapped back on itself. I trimmed the outline with a scissor and poked a new hole in the end where the original hole was under the tape. I attached the chord back to the metal bracket. The problem was still there, the power would go off after a few seconds and the VHS gear train would make a slight motion like it was getting stuck. I then removed the mounting screws on the VHS housing and lifted it off the board slightly (ther are 2 screws that need to be removed from the far side also). There is a small gear under the right side of the board that was not aligned with another gear. The alignment is between a pin on one gear and a hole on the other. After I aligned them I reassembled the unit. The power stays on now only if I leave a tape in it but the DVD and VHS seem to work. My problem now is that I can only select AUX and channel 2! On well thats my next battle. Good luck.
Posted on Dec 17, 2008
Tips for a great answer:
Feb 23, 2014 | Magnavox DV200MW8 DVD Player VCR Combo
Feb 12, 2011 | One For All URC-4021 Remote Control
May 22, 2010 | Philips 19MDTR20/99 19 in. TV/VCR/DVD...
Feb 15, 2010 | Philips Magnavox DVD/VCR Dual Player
Dec 28, 2009 | Philips Magnavox MWR20V6 DVD Recorder/VCR
Sep 27, 2009 | Philips Magnavox MWR20V6 DVD Recorder/VCR
May 04, 2009 | GoVideo Go Video DVD/VCR Combo
Feb 04, 2009 | Philips Magnavox MWR20V6 DVD Recorder/VCR
Jun 16, 2007 | Jensen JER-422 Universal Remote Control
22 people viewed this question
Usually answered in minutes!