Question about Makita 6935fdwdex 14.4v Impact Driver Drill

1 Answer

I have a Makita 6935 FDWDE. I need to separate the two halves for repairs but I can't figure out how. I have all current drawings but it doesn't really show anything.   Any help would be appreciated.

Posted by on


1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 20 achievements.


    An expert that got 10 achievements.


    An expert that got 5 achievements.

  • Makita Master
  • 1,995 Answers

Beware that if all the screws are removed try to open with a sharp knife between the housing and if not worked then knock him open with hammer around rapping , because of heat (melting) problems

Posted on Oct 12, 2016


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

Makita 9901 belt sander. How to separate the shell halves so I can replace the cord? I’ve got all the possible obvious bolts removed but something else is holding it. Hidden bolt, clips???

Have a close look for plugs covering hidden screws. Most power tools now have security screws in them to stop people opening them up. You may need to buy a set of special screwdriver bits to get these out.

Sep 30, 2018 | Makita Tools & Hardware - Others

1 Answer

98 buick century needs new alternator, i have alternator off 94 oldsmobile cutlass

Yes it is compatible. The only difference could be in the "clock position", that is if the wiring plug is not in the same position as your current alternator. If that is a problem, the bolts can be removed and the case halves rotated into the correct position. If you must separate the case halves, you will have to push the brushes back into their holder and insert a thin rod(a heavy paper clip will do) to keep them retracted in order to put the halves back together again. Don't forget to pull the paper clip out after reassembly.

Mar 02, 2018 | Buick Cars & Trucks

1 Answer

How do I wire up a switch on a 110 volt mlt100 makita tablesaw

You can still find inline switch for cords, but make sure they can handle the amperage. A 15A rating should be fine. Don't use a lamp-cord switch, because they are usually rated for much lower current.
Some people go to the trouble of mounting an electrical junction box on their machine and routing the cord through it with a light switch. Once again, the light switch must have a higher current rating of 10 or 15 amps, depending on the current-draw of your machine.

Feb 16, 2017 | Makita Saws

1 Answer

Can i bypass the switch on a makita skill saw

OMG, absolutely NOT!

I know a guy without 3 fingers due to one of those on a construction site. He said he never felt a thing.

Buy a new switch.

  • Makita Canada Inc. Makita Canada: The best in class for cordless power tool technology. A leader in power tool technology for the professional.
  • Makita Saw Parts ' Great Selection ' Great Prices ... Fix your Makita Saw today with parts, diagrams, accessories and repair advice from eReplacement Parts! Worldwide shipping, no hassle returns.
  • images of makita saw parts th?id=oip.m79ac54922c7af758ce5909fe9cde9163o0&w=87&h=105&c=7&rs=1&qlt=90&pid=3.1&rm=2th?id=oip.m8226e4e7540d1403e6b34f0609fee8ado0&w=87&h=105&c=7&rs=1&qlt=90&pid=3.1&rm=2th?id=oip.mc9c1b6c779ab4de644cda35842865ffbo0&w=87&h=105&c=7&rs=1&qlt=90&pid=3.1&rm=2th?id=oip.mfb5ac75b7411568957f4d7028521f0b4o0&w=80&h=105&c=7&rs=1&qlt=90&pid=3.1&rm=2th?id=oip.mdd935730eb9fe8614bf23952794b8ca9o0&w=87&h=105&c=7&rs=1&qlt=90&pid=3.1&rm=2th?id=oip.md1140885e7ec8b5124cabfe71fdb3085o0&w=87&h=105&c=7&rs=1&qlt=90&pid=3.1&rm=2 See more images of makita saw parts
  • Makita Power Tool Parts - Makita Parts - eReplacementParts We have the genuine Makita parts and tool repair help you need to get your power tools running like new again.
  • Makita Parts - Tool Replacement Parts ' Tool Parts Direct > Brands Makita Tool Parts - Shop Makita parts online at Tool Parts Direct. Over 38,000 Makita replacement parts and schematics available.
  • Related searches for makita saw parts
  • Makita Tool Parts :: Makita Saws - Tool Parts Canada ... Please choose your tool from Makita Benchtop line below view parts breakdown
  • Makita Saw Parts ' Sears PartsDirect > All Brands > Makita Parts Shop the best selection of Makita saws repair parts and accessories at Sears PartsDirect. Find replacement parts for any Makita saws repair project.
  • Makita - Authorized Factory Service Centers Makita Authorized Service Centers meet our high-quality ... Genuine quality Makita replacement parts; Most tools repaired within 3 days; Maximum Repair Cost Program;
  • Makita Saw Parts ' eBay 9k= Find great deals on eBay for Makita Saw Parts in Corded Circular Saws. Shop with confidence.
  • PARTS - Makita UK Parts . Ask Makita ' Find a dealer. Part search Search for tool drawing: Filter: 1 - 2 - 3 - 4 ... Contact Makita! 01908 211678. Monday - Friday 8am to 5:30pm.
  • Makita Tool Parts - Tool Parts Canada - Parts that makes ... Please Choose Makita category Below Which Matches Your Tool
  • Jun 20, 2016 | Makita Saws

    1 Answer

    How to reassemble bhp451?

    Here is a drawing

    Make sure you locate the magnet surrounding the motor in the housing correctly otherwise you will not be able to close the two halves of the outer case. You don't say how far you have taken it apart.

    Jun 08, 2012 | Makita Drills

    1 Answer

    How to dismantle a makita HP electrical hammer drill, want to replace the brushes

    Check out the split drawing on this page.
    If your makita does not have any outside accessible brush caps, you need to dismantle it.
    lay it on the side, where the side with the screws securing the to halves together is facing up.
    Remove all screws (some may be hidden under labels etc.) Gently pry the halves apart, locate the brushes disconnect their leads if any, and remove. Install new brushes and make sure the move freely, and that they are springloaded when in place. Gently rotate the rotor to ensure everything is ok . Reassemble and test drill. If the brushes leaves long streaks of noticeably large sparks, something has gone wrong or the rotor was damaged in the first place, causing excessive wear.

    Sep 13, 2010 | Makita HP1620F Electric Hammer Drills

    1 Answer

    How do I replace the power cord for a makita palm sander? Specifically once all the visible screws are removed how does one separate the two body havles?

    without knowing what the model number is you also have to remove the pad assembly and usually you will find some there if all removed you can GENTLY pry the cover halves apart. Go to with you model number and you can download a breakdown for this tool.

    Mar 14, 2010 | Makita Tools & Hardware - Others

    2 Answers

    Can't separate case to replace broken switch

    Have you removed the front housing? It has 4 screws that go into the handle halves and must be removed. As far as internal clips there are none. If you removed the front sometimes the handles stick together and you have to hold each piece and gently pull apart. Hope this helps

    Sep 26, 2008 | Makita 12V Cordless Impact Driver -...

    1 Answer

    Battery charger just flashes to say the battery has to cool down but will not start charging.tried another charger same thing happens but does not show that the batteries are faulty!

    Unfortunately, Makita’s li-ion battery packs have a design flaw. After having the same problem with my two batteries, I took it apart and saw the problem immediately. You see each battery pack has ten li-ion battery cells and a circuit board with a memory chip witch holds the charging history of the battery pack. But that memory chip constantly draws power from 2 of the 10 batteries. The current it draws is very small but if you consider it over 6 month or more, the power drain becomes very significant. You end up with a battery pack with 8 still fully charged battery cells and 2 drained battery cells. When you put this battery pack in the charger, it detects weak battery cells, assumes they are defective and refuses to charge. To avoid this problem you should charge your battery pack often, even if you haven't used it, every two months should be ok.
    I suspect that Makita doesn’t make these battery packs, they make power tools, good ones too. But Makita should definitely have a few words with their supplier before they become a liability!

    Jul 03, 2008 | Makita Tools 18V 1/2" Lxt Lithium - Ion...

    1 Answer

    My old KOSS TD/60 Stereophones have a broken cable right near the earphone entry point. How can I open the earphone to repair or replace the cable?

    I figured that that the earphones were pretty old, so if my 'repair' didn't work I would just replace them with new ones. There is a groove filled with acoustic foam that runs right around each earcup that terminates at the cord's entry point. After removing the headband yoke by carefully popping it out of each earcup I simply gripped both sides of the earcup and applied outward pressure until the front and back halves separated. Fortunately they are held together by plastic clips that snap apart. Once I had located the fault in the cable and repaired it the earcup halves easily snapped back into place. I now have a functioning set of headphones again!

    Apr 22, 2008 | Audio Players & Recorders

    Not finding what you are looking for?
    Makita 6935fdwdex 14.4v Impact Driver Drill Logo

    Related Topics:

    109 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Makita Tools & Hardware - Others Experts

    Jim Thurston

    Level 3 Expert

    672 Answers

    Mike Squire

    Level 2 Expert

    420 Answers

    John Trevino

    Level 3 Expert

    1395 Answers

    Are you a Makita Tool and Hardware - Other Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides