Question about Indesit W 123 Front Load Washer

1 Answer

Indesit WIE167 washing machine, displaying F03,

We have checked the filter and for blocked pipes but no luck

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 135 Answers

Error code f03 relates to the thermistor on the heating element.
This can be a faulty thermistor or bad contact between it and the control board.
Worst case scenario is a fault with the board which would mean a replacement.
Hope this helps & thanks for using Fixya

Posted on Dec 20, 2008

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Why is my air con leaking out the front of it I want to get to the overflow pipe inside but dont know how to remove the front caseing other than the filter part


Check where the condensate pipe goes onto the ground first as sometime spiders or wasps will block the end of the pipe. It is unlikely that the pipe is blocked inside although as you have seen the water does flow out inside..

Feb 29, 2016 | Filter Heating & Cooling

1 Answer

It is spinning but not pumping out water


Drainage problems can be caused by:
a) Blocked Filter chamber
b) Blocked Sump
c) Blocked Drain Pipe
d) Failed Pump

You can check the sump and drain pipe are not blocked by disconnecting the drain pipe from the undersink trap or waste pipe and lowering to a bowl on the floor. The water should drain out into this bowl under gravity if there are no blockages. If this drains then you can should check the filter chamber if it is accessible on your washing machine (not all are). I would recommend you unplug the machine or take the fuse out of the switched socket before doing this. Drain the drum as above before doing this or you will get a gush of water coming out. You will usually have to remove a cover from the bottom of your machine to get to the filter chamber and twist it ant-clockwise to unscrew it. Check for any coins buttons etc trapped in there. If there is nothing there check the impeller will turn relatively easily by hand. If you still can't find the problem you might have a faield pump and I would recommend contacting an engineer.

Apr 04, 2011 | Washing Machines

1 Answer

Wixl123 does not drain after washing ?


Drainage problems can be caused by:
a) Blocked Filter chamber
b) Blocked Sump
c) Blocked Drain Pipe

d) Blocked waste pipe
e) Failed Pump

You can check the sump and drain pipe are not blocked by disconnecting the drain pipe from the undersink trap or waste pipe and lowering to a bowl on the floor. The water should drain out into this bowl under gravity if there are no blockages. Bear in mind if you have disconnected the drain pipe from an undersink pipe if youpour the drained water down the sink it will flood into your undersink cupboard. If this drains then you check the waste pipe or undersink trap is clear. You should also check the filter chamber if it is accessible on your washing machine (not all are). I would recommend you unplug the machine or take the fuse out of the switched socket before doing this. Drain the drum as above before doing this or you will get a gush of water coming out. You will usually have to remove a cover from the bottom of your machine to get to the filter chamber and twist it ant-clockwise to unscrew it. Check for any coins buttons etc trapped in there. If there is nothing there check the impeller will turn relatively easily by hand. If you still can't find the problem you might have a faield pump and I would recommend contacting an enginee

Apr 03, 2011 | Indesit W 123 Front Load Washer

1 Answer

Wasing machine fills with water during washing and wont pump out filling the drum...


1. Empty the drum via the filter / trap at the front (there is sometimes a drain pipe near the filter - otherwise be prepared to use lots of towels to soak up the water).
2. Check / clean the filter.
3. Ensure that the drainage pipe is not blocked.
4. Check that the pipe from the pump to the waste water pipe is not kinked / blocked.
5. Check that the pipe from the drum to the pump is not blocked.
6. Does the pump sound like it's trying to work? If not, it could be that the pump is dead. Pumps can often become blocked with fluff / slime from the machine.

Good luck!

Jan 13, 2011 | Bosch Washing Machines

1 Answer

Water wont drain out of the dishwasher.I have checked the filters and all blockages.When you blow into the drain pipe it is blocked


Have you recently changed the disposal in you sink? If you have, make sure the knock out plug is removed and re-attach the drain pipe. Good Luck!

Jan 06, 2011 | Dishwashers

1 Answer

I don't think it is suctioning right


start by checking the filters on the unit. The filter cone and the little disk filter just above the cone are the perfect place to start.
Next see if there is something in the hose that may be blocking it. On this machine you can reverse **** the hose back into the canister.

look down the metal pipes for anything blocking the airflow there as well.

IF all of that is clear, and no blockage in the piping, then you may need to replace the belt on the power head. A lot of times this will stretch and not allow the unit to pick up properly.

Good luck with that.
Mark

Nov 12, 2010 | Filter Queen Majestic Canister Vacuum

1 Answer

No problem with wash and spin cycles but will not drain water after wash. Makes a ckicking noise when it should drain away


Hello,
It sounds very much like there is a blockage in the drain pump,when was the last time you checked the filter.It may be spinning ok but if the filter is blocked it may not be spinning fully or draining properly.There is also a good chance that the sump pipe and drain pipes are choked with sludge /limescale.Try the filter check first if no Joy then it will need investigating down by the pump.
Hope this is of some help.

Good Luck.

May 04, 2010 | Zanussi FJS1225W Front Load Washer

1 Answer

Water didnt pump out properly now its not coming out at all whats wrong


possible blocked pipe,while machine is full of water take the outlet pipe and lay this as low as possible into a bowl. if no water comes out then you have a blocked pipe. 1st if there is a filter remove drain plug and check filter. If no filter then you need to remove rear panel, Under the sump there is a large black hose, this goes to the pump. By removing the sump side of this hose with suitable tool you can check inside pipe. You may also need to check waste pipe aswell.

Feb 18, 2010 | Washing Machines

1 Answer

Front load washer will not fill with cold water and will just stop at the rinse cycle and buzz


Check your inlet pipe on cold water supply, When you dissconnect look inside where pipe fits onto machine you will see a small filter, if it is blocked take it out with great care and clean. always replace it. if your water supply is ok and filter is clear then it will be a faulty water valve. Good luck and feel free to give feed back ok.
John

Sep 03, 2009 | Kenmore Washing Machines

1 Answer

Won't drain!!


The washer has either a blocked or faulty pump, or a blocked filter.
Depending on the model number, the filter is either at the front bottom behind a removeable panel, or at the rear of the washer.
If you can't find a filter at the front, then remove lower rear cover of washer, remove the large black hose fastened to the bottom of the tub. Be careful, as there will be water run out.

Remove and clean plastic filter in hose.check pump is not blocked.
Refit filter and hose.
Please rate my fixya solution.
Thankyou.

Feb 07, 2009 | AEG Washing Machines

Not finding what you are looking for?
Indesit W 123 Front Load Washer Logo

617 people viewed this question

Ask a Question

Usually answered in minutes!

Top Indesit Washing Machines Experts

Gerry Harvey
Gerry Harvey

Level 3 Expert

1474 Answers

Donald DCruz
Donald DCruz

Level 3 Expert

17130 Answers

shaun taylor

Level 3 Expert

1527 Answers

Are you an Indesit Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...