Question about Samsung Color Fixed Security Camera Sod-14c

1 Answer

Samsung survalance cam sod12c

I need to know how to figure out the wire diagram. so i can change the plug to rca and power

Posted by on

  • hadi_assad Dec 20, 2008

    just need to what wires are positive and negative

  • Anonymous Dec 21, 2008

    that doesn;t work

×

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Scholar:

    An expert who has written 20 answers of more than 400 characters.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 141 Answers

Check on the electronic board inside the camera, you will probably see a few condensator with a "-" on it, just follow the connection and your negatif wire will be connected to it...
cheers

Posted on Dec 20, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

6 PIN DIN to RCA Converter Cable with power for security camera


WHOA we'll kinda hard when there are 50 different camera co out there need the camera co name and camera model

Jan 27, 2014 | Surveillance Cameras

1 Answer

Wire diagram


I can't seem to find a pin out, it you post what wires are there I can help you figure out the most likely pinout without damage to the device--Good Luck.

Feb 01, 2013 | Samsung Weather Resistant Security Camera...

1 Answer

Where would I find the wiring diagram for a Samsung Security Camera SOC-a101? It is a 6 prong plug and I need to connect a PS2 connector to it.


I have a Samsung soc-a101 digital color security camera, wires corroded off male plug to camera what is the wiring sequence to the plug? wires are: red 12 volt looking at pin's front side not back of plug, from plastic tab pointed up red is on right top terminal, audio is top left terminal which I assume is white wire, then I have a clear plastic covered wire and the bare stranded wire. what terminals go to these wires I assume the bare wire goes to the metal ring of the plug as it had a wire soldered to it just don't know which! this leaves the bottom pins on the left and right set of two and the two bottom pins! Can you help? remember I am looking at the front not back where the wires are soldered. Thanks.

Dec 07, 2012 | Samsung Soc-a101 Hi-res Outdoor Bullet...

1 Answer

Dome camra wire connection with bnc


Preparation
Before installing your RCA camera scout the area and confirm that you will be able to run the cable from your surveillance digital video recorder (SDVR) to your camera. You may want to use RG59 Siamese cable, which is a single cable system with three wires: a coaxial cable for the video and a positive and negative wire to provide power to the camera. If you are installing your camera outside, place it at least 10 feet high to minimize tampering, or put your camera in a dome or other protective housing.
Coax Cable
BNC connector
BNC connectors and cable image by Albert Lozano from Fotolia.com
BNC connector
If you use Siamese cable to wire your RCA camera, you will run the cable first, and then install a BNC (bayonet Neill-Concelman--named for the inventors) connector on each end of the cable. BNC connectors vary by manufacture; install the BNC connectors according to the connector instructions. To get a general overview of the process, see the Resources section for a video on installing BNC connectors.
Power Wires
Plug with standard lamp-type cord
element electric power black image by Leonid Nyshko from Fotolia.com
Plug with standard lamp-type cord
Your camera came with a power supply with an integrated power wire; the power supply plugs into a standard wall outlet and the other end plugs into your camera. The cord is probably not long enough, in which case you will have to cut it and splice the Siamese in the middle to deliver power to your camera. The power supply wire is designed like a standard lamp cord and must be cut in half and split. One of the wires will be marked with a stripe, a series of dashes, a rib on the insulator or some other marking (just like a lamp cord). The marking indicates that this is the positive wire. After cutting the supply cord, connect the portion with the camera plug on it to the Siamese cable at your camera and then connect the power supply portion to the other end of the Siamese cable near your SDVR. The positive (marked) power supply wire should be connected to the red Siamese wire and the other wire connected to the black Siamese wire. While many people use wire nuts to connect the wires, connecting the wires with a wire beanie (see Resources) will provide a higher quality installation.
Plug-and-Play
Plug-and-play cables make it easier for homeowners to install their cameras. These cables incorporate all three wires into one cable system and come with connectors preinstalled so that you will not have to install connectors or cut wires. This is slightly more costly than assembling your own cable, but it will save you time and you will not have to purchase special tools to install the connectors. Run your plug-and-play cable and connect it by following the instructions which come with your cable. See the Resources section for a video on installing plug-and-play cables.

Dec 16, 2010 | Dome (8) Cctv Dome Color Ccd Night Vision...

2 Answers

Need to determine wiring connections from camera to dvr for Samsung SSC DVR


Hi


Thanks for using FixYa. Please see the link to hook up DVR with camera---

Hookup Camera with DVR

Please do accept the solution if the issue is resolved or post a comment for further assistance.


Thanks
Rylee

Jun 16, 2010 | Samsung SSC DVR Digital Video Recorder...

2 Answers

Micromark wiring diagram


hi have the same issue found it to be red power black negative yellow video white audio and bare wire is the shared ground for the yellow and white hope this helps

Feb 09, 2010 | Swann Communications DVR4-Pro-Net...

1 Answer

Need wiring map for RJ11 conector for Samsung SOD-14C camera


Well good news and bad news if u just got shot ends easy cut end off and copy other end with new rj11 6 pin phone jack.. what im trying to do is give camera secondary 12v power and use the wire in the jack to splice into RCA type connector to work with my old dvr

Sep 12, 2009 | Samsung Color Fixed Security Camera...

1 Answer

I'VE BEEN GIVEN A PANASONIC WV-BL-204 VIDEO SURVALENCE CAMERA NOT SURE IF IT HOOKS TO A VCR DOES ANYONE HAVE A PICTURE OF HOW IT HOOKS UP


Hi, yes, you  can hook this camera up to a VCR. You need a BNC to RCA adaptor and a RCA cable. You can purchase these items at Radio Shack. Just connect the VIDEO OUT, which is a BNC connector to your yellow VIDEO IN RCA jack on the VCR. If you dont see video, then you might have to switch the 1st dip switch to enable the iris on the lens to open and let light through. Here is the manual:
http://www.cctvpros.com/files/14580.pdf

Mar 22, 2009 | Panasonic WV-CP244 Fixed Color Camera

1 Answer

Need wiring map for RJ11 conector for Samsung SOD-14C camera


I guess this is an ongoing issue with Samsung cameras. Did anyone EVER figure this one out?

Jan 20, 2009 | Samsung Color Fixed Security Camera...

Not finding what you are looking for?
Samsung Color Fixed Security Camera Sod-14c Logo

962 people viewed this question

Ask a Question

Usually answered in minutes!

Top Samsung Surveillance Cameras Experts

kakima

Level 3 Expert

96417 Answers

Bill

Level 1 Expert

30 Answers

Cindy Wells

Level 3 Expert

4755 Answers

Are you a Samsung Surveillance Camera Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...