Question about Lexmark E232 Laser Printer

1 Answer

My lexmark 232 shows the light "toner low/replace pc kit". how do i do that?

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Lexmark Master
  • 4,338 Answers

The Photoconductor Kit designed for use with Lexmark E230, E232, E232T, E238, E330, E332, E332N/TN, E240, E340 and E342. Yields 30,000 pages.

Have you printed 30,000 pages on this unit? If not perform the following reset:

Procedure for E-232 is:
1. press and hold Start
2. turn on the printer
- this is service mode -
- by pressing the Start you can print Printer Settings Configuration sheet -

3. press and release Cancel 4 time
4. Press and hold Start while all lights start cycle
5. press and hold Cancel untill all the light cycle
6. turn the printer off to exit the menus

If I could be of further assistance, let me know. If this helps or solves the issue, please rate it.
Thanks, Joe

Posted on Dec 20, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do I replace pc kit on Lexmark X 264dn


The PC kit is removed by grapping the handle on the toner cartridge and pulling up and out. Then press the grey button under the toner handle to remove the toner cartridge from the PC (photo conductor) unit. Install new PC unit in printer and install the toner into the PC unit. Check instructions with PC unit for reset instructions for the page counter.

Sep 22, 2014 | Lexmark X 264dn - multifunction Laser...

2 Answers

Grinding noise


could be the laser unit on top of the printer out of whack -i have the same fault also

Jun 29, 2012 | Lexmark E120n Laser Printer

1 Answer

Hello - my Lexmark E120 will print a test page, but won't print anything that I send to it. I just get an error message. There is a green light next to the 'lightbulb' on the printer. The...


The light next to the lightbulb on the printer Toner low/replace PC kit. The printer is ready to receive and process data. In addition, the toner in the toner cartridge is getting low.


Solution:

? Press continue button to clear message and continue processing job.

? Remove the toner cartridge. Gently shake the toner cartridge from side to side and front to back several times to redistribute the toner, and reinsert it. Repeat this procedure multiple times. If the print remains faded, replace the toner cartridge.

For further assistance, please contact Lexmark Technical Support

Sep 12, 2011 | Lexmark E120n Laser Printer

1 Answer

The printer toner light is continuously flashing even after putting in a new cartridge


After installing a new cartridge and the blinking light is on Toner Low, it means that the photoconductor is almost full and should be replaced soon. Press and release the Continue button (green button) to clear the light sequence and continue processing the print job. If the light is still blinking, replace the photoconductor kit.

For further assistance, please call Lexmark Technical Support.

Jun 14, 2011 | Lexmark E260D - QTY 4 - LMB OFFER Laser...

1 Answer

2 buttons of the lexmarkE260D are glowing> the


The light is second to the right is Toner Low. If ! and toner low displays a flashing light it means that the photoconductor kit is full and must be replaced. The printer will not print any more pages until the photoconductor kit is replaced.


Press and release Continue button to print a photoconductor kit instruction page. If the light is still blinking, replace the photoconductor kit.

For further assistance, please call Lexmark Technical Support.

Apr 12, 2011 | Lexmark E260D - QTY 4 - LMB OFFER Laser...

1 Answer

My toner cartridge was recently replaced (we use the proper cartridges, not refills) and within about 3 weeks (sooner than last time) the "toner low" light is flashing. The print quality is still perfect....


Whenever you replace the photoconductor kit, you will also need to manually reset the photoconductor page counter. Visit the Lexmark website at http://bit.ly/8YJwFU, for the instructions on how to reset the pc page count. You can also contact Lexmark technical support or your authorized service provider for additional assistance.

Sep 24, 2010 | Lexmark E250dn Laser Printer

1 Answer

Replaced toner and maintenance kit -keep getting yellow lights on exclamation and toner


If the toner and the exclamation lights are blinking yellow after replacing the toner and maintenance kit, then you will need to reset the photoconductor counter. But if the exclamation and the toner lights are steady on yellow, then that means there is something wrong with the toner.

Jul 27, 2010 | Lexmark E260dn Laser Printer

1 Answer

The printer reports states low pc kit. I have changed the kit and toner and it still is binking.


After replacing the kit and toner, you will need to reset the printer's page count. Simply press and hold the CANCEL button while the printer is on and the front cover open until all lights are flashing. Hope this helps.

Jul 05, 2010 | Lexmark E260dn Laser Printer

1 Answer

Lexmark e250dn printer, toner light is flashing, new cartridge


Could be photoconductor at end of life.

You shoul still be able to do a printer test print (press the arrow button).

Look on the printed pagesfor Toner AND Photoconductor.

These show as OK when new or very low count, and 100% when fully used.

If the toner is showing as 100% when you've just replaced it, either the chip is faulty, the wrong one, or if the cartridge is a remanufactured one possibly nor been replaced.

Jan 19, 2009 | Lexmark E250dn Laser Printer

1 Answer

Toner light still blinking orange after new toner installed. Rebooted printer, light still blinking.


It means you need to replace the photoconductor kit (the bit the toner fits into) reset information is supplied with the new photoconductor kit.

Oct 15, 2008 | Lexmark E232 Laser Printer

Not finding what you are looking for?
Lexmark E232 Laser Printer Logo

823 people viewed this question

Ask a Question

Usually answered in minutes!

Top Lexmark Printers & Copiers Experts

Roopesh S
Roopesh S

Level 2 Expert

228 Answers

Sanath Kumar V

Level 3 Expert

684 Answers

Les Dickinson
Les Dickinson

Level 3 Expert

18297 Answers

Are you a Lexmark Printer and Copier Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...