Put the phone to your ear and press any digit---you should hear a short burst of tone--if not you may be analogue pulsing which takes forever wait wait wait or change your phone to send tones instead.do this or check this in the menu for whatever kind of phone you are using....i hope this helps
a 6ya Technician can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US. click here to Talk to a Technician (only for users in the US for now) and get all the help you need. Goodluck!
- If you need clarification, ask it in the comment box above.
- Better answers use proper spelling and grammar.
- Provide details, support with references or personal experience.
Tell us some more! Your answer needs to include more details to help people.You can't post answers that contain an email address.Please enter a valid email address.The email address entered is already associated to an account.Login to postPlease use English characters only.
Tip: The max point reward for answering a question is 15.
try changing phone to tone dialing . one phone line has been setup for Decadic dialing and the other line may be setup for tone dialing.
If tone dialing is working on one line but not the other then get phone company to change the dialing type on the phone line.
Dual tone multi frequency is the technical name for tone dialing and is more efficient than decadic dialing or pulse dialing.
Is there a dial tone? And have you tried another phone? If there is a dial tone make sure the phone is set for tone dialing. There will either be a switch on the side of phone for pulse or tone, set for tone. or go into the menu and look for it there...
Either button mapping or no dial tone at the system cabinet. If your desplay sas CO1 and you have no dial tone, go to the sytsem cabinet ans swap the modular plugs for CO1 and CO2. If the No Dial Tone moves, "mus be sumpin wrong wit yo lines".
Here's what the manual says:
Changing the Dial Mode (Tone or Pulse Dialing)
Your phone can communicate with the telephone network in two different
ways: tone dialing or pulse dialing. These days, most phone networks use a
method called tone dialing, so your phone comes programmed for tone dialing.
If your phone company uses pulse dialing, you need to change your phone's
dial mode. If you don't get a dial tone or can't connect to the telephone
network, follow the steps below to modify your phone?s settings:
With the phone in standby, press and hold [cid/menu].
Press [vol/ / ] to move the pointer to select DIAL.
Press [select/channel] to set the phone to pulse dialing.
Return the handset to the base. The handset communicates the new
setting to the base, and the base activates the setting on any other
Hope this helps out.
This problem can
be due to the software not handling a certain dial tone rather than a
specific hardware fault. Around the world there is a variance in the
signal quality of the dial tone which causes a report of no dial tone
detection. Disable the dial tone detection to prevent the system from
trying to detect a dial tone.
Disabling dial tone detection for modems: Windows XP
Select Control Panel
Click Switch to Classic View to change the control panel view
Click Phone and Modem Options
Select the Modem Tab
Select the installed modem (Example: Lucent Technologies Soft Modem AMR)
Click the Properties button
Select the Modem tab in the Properties window
Click Wait for dial tone before dialing to remove the check from the checkbox
Select the Advanced tab
Add X3 to the Extra initialization commands field in the Extra Settings box
Click OK twice
Select Switch to Category View to change back the control panel view
Close Control Panel
if this does not work trying re-installing modem drivers.
The problem is possibly the keypad on the phone. Try another phone , preferrably a standard corded phone. If you still cannot break the dial tone, then the problem is with the telephone line (phone company)
If the 900MHZ phone is Model 26928M programming for rotary dial usually goes like below, can't hurt to try on any model.
This adjustment allows you to select tone (touch-tone) or pulse (rotary) mode dialing. The phone is pre-set for
touch-tone use. To set to tone or pulse dialing:
1. Press and hold the program button for two seconds. You will hear a beep.
2. Press the *tone button to select Tone Dialing or press #pause to select Pulse Dialing.
3. Press the program button again. You will hear a confirmation tone.