Question about Fantom Vacums Cyclone XT Upright Vacuum

1 Answer

How do i replace the belt in the Fantom Cyclone XT vacuum

I have a fantom cyclone xt vacuum. i have tried everything and i could not find the screws. when i turn the brushes on, they turn on and off, almost like theres a loose wire.

Posted by on

  • TDFLOWING Apr 09, 2009

    HOW DO YOU GET THE BULB OUT TO REPLACE THE BELT THANKS TERESA

×

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Expert
  • 373 Answers

Remove the covers over the headlights and under the shiny foul. there are two screws. there are two tabs that hold down the cover over the wheels, they just pop on/off with a click.
on my xt. i had to remove the rolling brush and clean out all the hair that was stuck in the bearings. remove the screw holding down the motor and belt. pry out the roller brush to get to the bearings. there was some serious hair ball in there.
reassembled mine and it works perfectly now :)

Posted on Feb 18, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Fantom F11063 Cyclone Vaccum


I think the manual can help you in replugging the wires

How did you pull out the wires from circuit board ?
Is it with professional help or through some other means



Sep 18, 2008 | Fantom Vacums Cyclone XT Upright Vacuum

1 Answer

How do you open it where the brush is located.


Remove the 2 lens caps where the headlights are.
Push and twist the two lights out, these are spring loaded.
There should be 2 screws, one under each headlight.

Once the screws are removed it should be easy to take the top cover off so that you can get to the brush.

Good luck.

Nov 06, 2010 | Fantom Vacums Cyclone XT Upright Vacuum

1 Answer

I have a Fantom Thunder Vacuum. Missed placed my book. How do you replace the belt on the brush?


depending on your model, and I am going from memory on this one. I have not seen this model in a while.

1 headlight on the unit:
there are 2 screws on the back of the cover for the brush. Just above the wheels. Remove those two screws and the cover will come off.

2 headlights on the unit:
use a small screwdriver to remove the headlight lens covers, remove both of the light bulbs, and then the two screws are under the lights. there MAY be 2 more screws again at the back of the unit above the 2 rear wheels to remove as well. again the cover should come off and you will have full access to the belt/brush under there.

Nov 04, 2010 | Fantom Vacums Cyclone XT Upright Vacuum

2 Answers

Replace belt on fantom cyclone vacuum? the manual does not decribe replacing the roller belt - i can't get it open to expose the belt


On my 10-year-old model, the two screws securing the cover are under the two llight bulbs. Pry off the clear plastic covers, take out the bulbs and screws, and the cover lifts off.

Dec 01, 2009 | Fantom Vacums Cyclone XT Upright Vacuum

1 Answer

Remove brush motor


first pry out the lens over the headlights. under the foil are two screws holding the top cover on. just lift carefully and the back of the cover pops off. the motor is easily removed, just one screw holds it in place.

Jun 02, 2009 | Fantom Vacums Cyclone XT Upright Vacuum

1 Answer

Brush wont spin


Sound like it has a bad belt . I would check it and replace if bad .

Feb 22, 2009 | Fantom Vacums Cyclone XT Upright Vacuum

1 Answer

I am trying to get to the belt on my fantom cyclone xt, although I am unable to see any screws to remove. I took the rubber bumper off thinking this would be of some help although nothing there either. Can...


remove the lens covers, bulbs and the foil. under the foil are two screws. remove the screws and the cover lifts off. the motor for the belt is held in with one screw.

Jan 03, 2009 | Fantom Vacums Cyclone XT Upright Vacuum

Not finding what you are looking for?
Fantom Vacums Cyclone XT Upright Vacuum Logo

Related Topics:

1,089 people viewed this question

Ask a Question

Usually answered in minutes!

Top Fantom Vacums Vacuums Experts

Roger Potts

Level 3 Expert

694 Answers

Les Dickinson
Les Dickinson

Level 3 Expert

18375 Answers

Mike Cairns
Mike Cairns

Level 3 Expert

3053 Answers

Are you a Fantom Vacums Vacuum Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...