Question about Schwinn Bicycle Accessories

1 Answer

Instruction for schwinn bike odometer

For size 700 wheel.What number do I set into the computer.I lost my instructions

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.


    An expert that hasĀ over 10 points.


    An expert whose answer gotĀ voted for 2 times.

  • Contributor
  • 1 Answer

Find the circumference of the tire (measure the radius and multiply by 2 PI or 6.28) and convert it to millimeters--thats the number you put into the computer. I think you should get about 2154 mm depending on your tire inflation, but that doesnt make that much difference.

Posted on May 21, 2009

Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

2 Answers

The wheel size chart in the instruction manual does not include a tyre size of 700 x 54c (29 x 2.1) so I can't set it. Can you advise the setting requied?

It's in the manual. Measure the wheel size and enter it manually.

There's a picture of how to determine the circumference by rolling the wheel one revolution and measuring it. Be as accurate as you can (to the mm).

4. Wheel size BIKE 1

• Press MODE to change to BIKE 1.

• Press SET briefly and the first digit flashes.

• Set the value by pressing RESET, change to the next digit by pressing MODE.
• Bike 1 is always the bike with the handlebar holder WS 1

Feb 05, 2011 | Sigma Sport BC1106 Dts Wireless Bike...

1 Answer

I HAVE TWICE POSTED MY PROBLEM ALRAEDY IN THE LAST COUPLE OF HOURS,. i HAVE A N ECHO Wireless Computer W1 - in changing this between bikes I have somehow manges to lose the setting up instructions, I am...

Go back to where you bought it and see if they have an extra set of directions. If, they don't maybe they can call the manufacturer of Echo. Or you neighborhood bike shop mechanic may know the numbers for your wheel size.

Aug 22, 2010 | Bicycle Accessories

1 Answer


um take it to bike shop there had to work ay um or just play around with it and look at instructions

Nov 14, 2009 | Cadence Cat Eye Strada Computer

1 Answer

Wheel size

2105mm should get you very close.

Aug 13, 2009 | Sigma Sport BC1106 Dts Wireless Bike...

1 Answer

Cant remember what seting my schwinn speedometer is suposto be at can some one help?

If its model sw 654 like my wifes'You need to first determine the circumference of your front wheel.Try this,with the valve stem at total bottom of the tire ,on the front wheel where you have the sensor mounted,make a mark on a sidewalk.Then slowly move the bike in a straight line, untill the valve,again meets the surface of the sidewalk.With these two marks, measure with a tape measure, on my wifes 26 inch front tire its 82.25 inches.Take these measurements,multiply 25.4[the number in millimeters in an inch} write this number down! Now on model 654 odometer,hold down both the left and right side buttons,there seems to be only one button,but there is two,hold it in for aprox,5 seconds.and this resets the entire unit.The first thing it asks for,is this figure,a four digit number,in millimeters,on my wifes tire it is 2089milllimeters.Enter these numbers in a right to left fashion.Its tricky ,but it is a good unit,in the end if you can't figure it out,buy a new one ,and this time save the instructions,unlike myself!

Jun 11, 2009 | Bicycle Accessories

1 Answer

Wheel setting

700 x 25 = 2146

You should be all set :)

May 04, 2009 | Sigma Sport BC1106 Dts Wireless Bike...

6 Answers

Lost manual to Bell wireless bicycle computer

Here are some things the book doesn't tell you:
You have to completely reset the speedometer and lose your odometer to reset the MPH. Hold both buttons for 3 secs to get reset. (Remember to use the left button to walk through the setup process and use the right button to change the settings.) First set the wheel size using Ideluna's settings above on this page (right button to change the setting and left button to go to next number). Next is MPH/KPH, after wheel size setting, push left button again and km flashes. Push right button to change the setting to MI. Next is TIME. Push left button and you'll see the time. Hold down left button till 24hr appears. Push right button to change to 12hr. Then push left button to go to flashing hour. Change with right button. Then left button to go to flashing minute. Right button to change minute, hold down to change minutes fast. Now you are set up. Now the process changes, use the right button to walk through the menu and use the left button to reset. Don't push both buttons anymore unless you want to reset everything again. If you want to reset something just hold the left button down until 0. When you are in SCAN mode, push the right button to go to Time, To go back to SCAN once, hold the right button down - It will scan everything once and return to TIME. To go to ODO, push right button once, push again for DST, push again for MXS, push again for AVS, push again for TM, push again for SCAN to stay in SCAN.

Mar 24, 2009 | Bicycle Accessories

Not finding what you are looking for?
Bicycle Accessories Logo

Related Topics:

3,176 people viewed this question

Ask a Question

Usually answered in minutes!

Top Schwinn Bicycle Accessories Experts

Carl Marquardt
Carl Marquardt

Level 1 Expert

29 Answers


Level 3 Expert

2598 Answers

D. E. Hev

Level 3 Expert

1059 Answers

Are you a Schwinn Bicycle Accessory Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides