Question about Dishwashers

1 Answer

Kenmore 74362 My model# is 665.74362400 this unit is only just over one year old. My problem is it shut down and the quick rinse light started blinking. I have tried some of the button-reset procedures that were on some other responses but to no avell I even left it unplugged for a while. Any impute would be appreciated. I have a Kenmore Dishwasher Model #74362. After we run a cycle for a normal wash and heated dry the dishes are all very dirty and greasy. It is as if they were never washed. They actually come out worse then they were put in. I always rinse before putting in because I usually run a cycle once a week. Now all the dishwasher soap is caked up in the dispenser. My dishwasher is only 3 years old. What should I do?

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

I had the same issue and you will never beleive the solution.
Steps to follow:
1) run one full cycle with no dishes or soap
2) run one full cycle with a dishwasher cleaner like Jetdry
3) run one full cycle with a gallon of white vinager
4) never put soap in the extra in and only fill the main soap bin half way.

should work fine from here on out, but never fill main bin more then half way when you do dishes. also run the hot water in the sink until the water is very hot before starting the dish washer.

Posted on Jan 12, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Kenmore Elite 665.15929001 Dishwasher, flashing Sani-Rinse light, won't start


Kenmore is **** with a double PP go buy a Maytag or GE and throw it threw the appliance dept like the Discount tire guy did on TV. I have asked the same question on 4 different blog's and no answer. The question to where they were actually built is unavailable. They only warranty products for 1 year and their disclaimer's add up to when you walk out the door. They are just JUNK! sorry I do not know the answer, first you will pay the repair man then end up buying a new one anyway. Same as me..Peace!

Nov 14, 2012 | Dishwashers

1 Answer

We have a Kenmore dishwaher model#665.15772990 the no heat dry light was flashing and we could not get it to reset. So we replaced the board. It has been 1 month and now the quick rinse light is flashing....


sometimes it is because of a stuck button, push-tap the buttons
and see if it does anything otherwise sorry.
here's a link if you need it.
http://www.applianceblog.com/mainforums/threads/38660-kenmore-665-15632000-blinking-quick-rinse-light-after-replacing-control-board

Dec 31, 2017 | Kenmore Dishwashers

1 Answer

My Kenmore dishwasher starts to fill and then stops


I've got the same dishwasher....mine is 2 years old and used only 3 times a week and now the motor is burnt out. I understand that this unit is a Frigidaire and is one of the worst ..quality speaking. I guess that why they only provide an one year warranty. Unfortunately, we got a LEMON

Oct 04, 2009 | Kenmore Dishwashers

1 Answer

I replaced the igniter (glow bar)on our Kenmore


IF THE UNIT IS 14 YEARS OLD BE CAREFUL THE GAS VALVE MAY BE GETTING TO THE POINT WHERE IT IS NOT SHUTTING OFF AS QUICK AS IT USE TOO, YES THIS WOULD CONCERN ME ,YOU DON'T KNOW IF ONES OF THESE TIMES THE GAS VALVE MAY NOT SHUT AND GAS BUILD UP COULD BE POSSIBLE ,NOT A GOOD THING. PLEASE BE CAREFUL

Aug 31, 2009 | Kenmore 33464 / 33465 / 33469 Gas Single...

1 Answer

Kenmore dishwasher 16764 Quick Rinse Light won't go off


you can try reseating the ribbon cable on the board however i strongly believe you have a stuck key and the key panel will need to be replaced.

Feb 02, 2009 | Kenmore 16764 Dishwasher

1 Answer

Blinking quick rinse and lock on lights


Try holding down the "lock" button.It may be the way to unlock the problem.

May 26, 2008 | Kenmore 16602 / 16604 / 16609 Built-in...

1 Answer

Kenmore 74362


The blinking buttons indicate the buttons are bad. The console will have to be replaced.

May 14, 2007 | Kenmore 16919 Built-in Dishwasher

2 Answers

My Kenmore diswasher gets stuck between the quick rinse and drying cycle


I am having the same issue as described above. I think it is either the timer, thermostat (temp assure), or thermostat (temp boost) that needs replacing. The dial gets stucks in both the wash temp boost cycle and rinse temp boost cycle. However, I don't have a picture of the temp assure or boost part. Does anyone know how to fix this? Thanks. -Bill

Aug 31, 2006 | Kenmore 16602 / 16604 / 16609 Built-in...

Not finding what you are looking for?
Dishwashers Logo

Related Topics:

282 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dishwashers Experts

Donald DCruz
Donald DCruz

Level 3 Expert

17130 Answers

Marvin
Marvin

Level 3 Expert

81400 Answers

Brad Brown

Level 3 Expert

17446 Answers

Are you a Dishwasher Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...